PW-CEP-STD-MIB DEFINITIONS ::= BEGIN

IMPORTS
	MODULE-IDENTITY,
	OBJECT-TYPE,
	Integer32,
	Counter32,
	Unsigned32,
	Counter64,
	mib-2
		FROM SNMPv2-SMI		-- [RFC2578]
	MODULE-COMPLIANCE,
	OBJECT-GROUP
		FROM SNMPv2-CONF		-- [RFC2580]
	TEXTUAL-CONVENTION,
	TruthValue,
	RowStatus,
	StorageType,
	TimeStamp
		FROM SNMPv2-TC		-- [RFC2579]
	SnmpAdminString
		FROM SNMP-FRAMEWORK-MIB		-- [RFC3411]
	InterfaceIndexOrZero,
	InterfaceIndex
		FROM IF-MIB		-- [RFC2863]
	PerfCurrentCount,
	PerfIntervalCount
		FROM PerfHist-TC-MIB		-- [RFC3593]
	HCPerfCurrentCount,
	HCPerfIntervalCount,
	HCPerfTimeElapsed,
	HCPerfValidIntervals
		FROM HC-PerfHist-TC-MIB		-- [RFC3705]
	pwIndex
		FROM PW-STD-MIB		-- [RFC5601]
	PwCfgIndexOrzero
		FROM PW-TC-STD-MIB		-- [RFC5542]
;

-- The PW CEP MIB

pwCepStdMIB MODULE-IDENTITY
	LAST-UPDATED "201105160000Z"	-- May 16, 2011 12:00:00 AM
	ORGANIZATION "Pseudowire Emulation Edge-to-Edge (PWE3)
Working Group"
	CONTACT-INFO
		"David Zelig (Ed.)
		Email: david_zelig@pmc-sierra.com

		Ron Cohen (Ed.)
		Email: ronc@resolutenetworks.com

		Thomas D. Nadeau (Ed.)
		Email: Thomas.Nadeau@ca.com

		The PWE3 Working Group
		Email: pwe3@ietf.org (email distribution)
		http://www.ietf.org/html.charters/pwe3-charter.html"
	DESCRIPTION
		"This MIB module contains managed object definitions for
		Circuit Emulation over Packet (CEP) as in [RFC4842]:  Malis,
		A., Prayson, P., Cohen, R., and D. Zelig. 'Synchronous
		Optical Network/Synchronous Digital Hierarchy (SONET/SDH)
		Circuit Emulation over Packet (CEP)', RFC 4842.







		Copyright (c) 2011 IETF Trust and the persons identified as
		authors of the code.  All rights reserved.

		Redistribution and use in source and binary forms, with or
		without modification, is permitted pursuant to, and subject
		to the license terms contained in, the Simplified BSD
		License set forth in Section 4.c of the IETF Trust's Legal
		Provisions Relating to IETF Documents
		(http://trustee.ietf.org/license-info)."
	REVISION "201105160000Z"	-- May 16, 2011 12:00:00 AM
	DESCRIPTION
		"This MIB module published as part of RFC 6240."
	-- 1.3.6.1.2.1.200
	::= { mib-2 200 }


-- Local textual conventions

PwCepSonetEbm ::= TEXTUAL-CONVENTION
	STATUS  current
	DESCRIPTION
		"Equipped Bit Mask (EBM) used for fractional STS-1/Virtual
		Circuit 3 (VC-3).  The EBM bits are the 28 least
		significant bits out of the 32-bit value."
	SYNTAX Unsigned32


PwCepSdhVc4Ebm ::= TEXTUAL-CONVENTION
	STATUS  current
	DESCRIPTION
		"Equipped Bit Mask (EBM) used for each Tributary Unit Group
		3 (TUG-3) in fractional VC-4 circuits.  The EBM bits are
		the 30 least significant bits out of the 32-bit value."
	SYNTAX Unsigned32


PwCepSonetVtgMap ::= TEXTUAL-CONVENTION
	STATUS  current
	DESCRIPTION
		"The VT/VC types carried in the 7 VT groups (VTGs)/TUG-2s.
		The format is 28 bits in the form of an Equipped Bit Mask
		(EBM) for fractional STS-1/VC-3.  The mapping specifies the
		maximal occupancies of VT/VC within each VTG/TUG-2.  For
		example, all four bits are set to 1 in this object to
		represent a VTG carrying VT1.5/VC11s, while only three
		are set when VT2/VC12s are carried within this VTG.
		The relevant bits are the 28 least significant bits out of
		the 32-bit value."
	SYNTAX Unsigned32


PwCepFracAsyncMap ::= TEXTUAL-CONVENTION
	STATUS  current
	DESCRIPTION
		"The type of asynchronous mapping carried inside STS-1,
		VC-3, or TUG-3 containing TU-3 circuit."
	SYNTAX INTEGER {
			other(1),
			ds3(2),
			e3(3) }


-- Top-level components of this MIB module
-- Tables, Scalars

pwCepObjects OBJECT IDENTIFIER 
	-- 1.3.6.1.2.1.200.1
	::= { pwCepStdMIB 1 }

-- Conformance

pwCepConformance OBJECT IDENTIFIER 
	-- 1.3.6.1.2.1.200.2
	::= { pwCepStdMIB 2 }

-- CEP PW Table

pwCepTable OBJECT-TYPE
	SYNTAX  SEQUENCE OF PwCepEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"This table contains objects and parameters for managing and
		monitoring the CEP PW."
	-- 1.3.6.1.2.1.200.1.1
	::= { pwCepObjects 1 }


pwCepEntry OBJECT-TYPE
	SYNTAX  PwCepEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"Each entry represents the association of a SONET/SDH path or
		VT to a PW.  This table is indexed by the pwIndex of the
		applicable PW entry in the pwTable.

		An entry is created in this table by the agent for every
		entry in the pwTable with a pwType equal to 'cep'.

		All read-write objects in this table MAY be changed at any
		time; however, change of some objects (for example
		pwCepCfgIndex) during PW forwarding state may cause
		traffic disruption.





		Manual entries in this table SHOULD be preserved after a
		reboot.  The agent MUST ensure the integrity of those
		entries.  If the set of entries of a specific row are found
		to be inconsistent after reboot, the PW pwOperStatus MUST
		be declared as notPresent(5)."
	INDEX {
		pwIndex }
	-- 1.3.6.1.2.1.200.1.1.1
	::= { pwCepTable 1 }


PwCepEntry ::= SEQUENCE {

	pwCepType                     INTEGER,
	pwCepSonetIfIndex             InterfaceIndexOrZero,
	pwCepSonetConfigErrorOrStatus BITS,
	pwCepCfgIndex                 PwCfgIndexOrzero,
	pwCepTimeElapsed              HCPerfTimeElapsed,
	pwCepValidIntervals           HCPerfValidIntervals,
	pwCepIndications              BITS,
	pwCepLastEsTimeStamp          TimeStamp,
	pwCepPeerCepOption            Unsigned32 }


pwCepType OBJECT-TYPE
	SYNTAX  INTEGER {
			spe(1),
			vt(2),
			fracSpe(3) }
	MAX-ACCESS read-write
	STATUS  current
	DESCRIPTION
		"Specifies the sub-type of CEP PW.  Currently only
		structured types are supported:

		'spe'(1)      : SONET STS-Nc signals.
		'vt' (2)      : SONET VT-x (x=1.5,2,3,6) signals.
		'fracSpe' (3) : SONET fractional STS-1 or SDH fractional
		                VC-3 or VC-4 carrying tributaries or
		                asynchronous signals.

		Support of 'vt' mode or 'fracSpe' mode is optional."
	DEFVAL { spe }
	-- 1.3.6.1.2.1.200.1.1.1.1
	::= { pwCepEntry 1 }


pwCepSonetIfIndex OBJECT-TYPE
	SYNTAX  InterfaceIndexOrZero
	MAX-ACCESS read-write
	STATUS  current
	DESCRIPTION
		"This is a unique index within the ifTable.  It represents
		the interface index for the SONET path for SPE emulation
		([RFC3592], Section 3.3), an interface index for the SONET
		VT ([RFC3592], Section 3.4) if the VT to be emulated is
		extracted from a SONET signal or locally mapped from a
		physical interface.

		A value of zero indicates an interface index that has yet
		to be determined.

		Once set, if the SONET ifIndex is (for some reason) later
		removed, the agent MAY delete the associated PW rows
		(e.g., this pwCepTableEntry).  If the agent does not
		delete the rows, it is RECOMMENDED that the agent set this
		object to zero."
	-- 1.3.6.1.2.1.200.1.1.1.2
	::= { pwCepEntry 2 }


pwCepSonetConfigErrorOrStatus OBJECT-TYPE
	SYNTAX  BITS {
			other(0),
			timeslotInUse(1),
			timeslotMisuse(2),
			peerDbaIncompatible(3),   	-- Status only
			peerEbmIncompatible(4),
			peerRtpIncompatible(5),
			peerAsyncIncompatible(6),
			peerDbaAsymmetric(7),     	-- Status only
			peerEbmAsymmetric(8),
			peerRtpAsymmetric(9),
			peerAsyncAsymmetric(10) }
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"This object reports a configuration mismatch inside
		the local node or between the local node and the peer node.
		Some bits indicate an error, and some are simply status
		reports that do not affect the forwarding process.

		'timeslotInUse'(1) is set when another CEP PW has already
		reserved a timeslot (or timeslots) that this CEP PW is
		attempting to reserve.





		'timeslotMisuse'(2) is set when the stated timeslot this
		PW is trying to use is not legal, for example, if
		specifying a starting timeslot of 45 for a SONET path of
		an STS-12c width.

		The peerZZZIncompatible bits are set if the local
		configuration is not compatible with the peer configuration
		as available from the CEP option received from the peer
		through the signaling process and the local node cannot
		support such asymmetric configuration.

		The peerZZZAsymmetric bits are set if the local
		configuration is not compatible with the peer configuration
		as available from the CEP option received from the peer
		through the signaling process, but the local node can
		support such asymmetric configuration."
	REFERENCE
		"Malis, A., et al., 'Synchronous Optical Network/Synchronous
		Digital Hierarchy (SONET/SDH) Circuit Emulation over Packet
		(CEP)', RFC 4842, Section 12."
	-- 1.3.6.1.2.1.200.1.1.1.3
	::= { pwCepEntry 3 }


pwCepCfgIndex OBJECT-TYPE
	SYNTAX  PwCfgIndexOrzero
	MAX-ACCESS read-write
	STATUS  current
	DESCRIPTION
		"Index to CEP configuration table below.  Multiple CEP PWs
		MAY share a single pwCepCfgEntry.

		The value 0 indicates that no entries are available."
	-- 1.3.6.1.2.1.200.1.1.1.4
	::= { pwCepEntry 4 }


pwCepTimeElapsed OBJECT-TYPE
	SYNTAX  HCPerfTimeElapsed
	UNITS	"seconds"
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The number of seconds, including partial seconds,
		that have elapsed since the beginning of the current
		measurement period.  If, for some reason such as an
		adjustment in the system's time-of-day clock, the
		current interval exceeds the maximum value, the
		agent will return the maximum value."
	-- 1.3.6.1.2.1.200.1.1.1.5
	::= { pwCepEntry 5 }


pwCepValidIntervals OBJECT-TYPE
	SYNTAX  HCPerfValidIntervals
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The number (n) of previous 15-minute intervals for which
		data was collected.

		An agent with CEP capability MUST be capable of supporting
		at least 4 intervals.  The RECOMMENDED default value for
		n is 32, and n MUST NOT exceed 96."
	-- 1.3.6.1.2.1.200.1.1.1.6
	::= { pwCepEntry 6 }


pwCepIndications OBJECT-TYPE
	SYNTAX  BITS {
			missingPkt(0),
			ooRngDropped(1),
			jtrBfrUnder(2),
			pktMalformed(3),
			lops(4),
			cepRdi(5),
			cepAis(6),
			badHdrStack(7),
			cepNeFailure(8),
			cepFeFailure(9) }
	MAX-ACCESS read-write
	STATUS  current
	DESCRIPTION
		"Definitions:

		'missingPkt'(0) - While playing out a sequence of packets,
		at least one packet was determined to be missing based on a
		gap in the CEP sequence number.  Note: If the implementation
		supports packet reordering, detecting gaps SHOULD take
		place as they are played out, not as they arrive.  This
		provides time for misordered packets to arrive late.

		'ooRngDropped'(1) - At least one packet arrived outside the
		range of the jitter buffer.  This may be because the
		jitter buffer is full or the sequence number addresses
		a buffer outside the current jitter buffer range or
		an already occupied buffer within range.  Whether or not
		packet reordering is supported by the implementation, this
		indication MUST be supported.








		'jtrBfrUnder'(2) - The jitter buffer underflowed because
		not enough packets arrived as packets were being
		played out.

		'pktMalformed'(3) - Any error related to unexpected
		packet format (except bad header stack) or unexpected
		length.

		'lops'(4) - Loss of Packet Synchronization.

		'cepRdi'(5) - Circuit Emulation over Packet Remote Defect
		Indication.  Remote Defect Indication (RDI) is generated by
		the remote CEP de-packetizer when LOPS is detected.

		'cepAis'(6) - Remote CEP packetizer has detected an Alarm
		Indication Signal (AIS) on its incoming SONET stream.
		cepAis MUST NOT (in itself) cause a CEP PW down
		notification.

		'badHdrStack'(7) - Set when the number of
		CEP header extensions detected in incoming packets does
		not match the expected number.

		'cepNeFailure'(8) - Set when CEP-NE failure is currently
		declared.

		'cepFeFailure'(8) - Set when CEP-FE failure is currently
		declared.

		This object MUST hold the accumulated indications until the
		next SNMP write that clear the indication(s).

		Writing a non-zero value MUST fail.

		Currently, there is no hierarchy of CEP defects.

		The algorithm used to capture these indications
		is implementation specific."
	-- 1.3.6.1.2.1.200.1.1.1.7
	::= { pwCepEntry 7 }


pwCepLastEsTimeStamp OBJECT-TYPE
	SYNTAX  TimeStamp
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The value of sysUpTime on the most recent occasion at which
		the CEP PW entered the Errored Seconds (ES) or Severely
		Errored Seconds (SES) state."
	-- 1.3.6.1.2.1.200.1.1.1.8
	::= { pwCepEntry 8 }


pwCepPeerCepOption OBJECT-TYPE
	SYNTAX  Unsigned32
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The value of the CEP option parameter as received from the
		peer by the PW signaling protocol."
	-- 1.3.6.1.2.1.200.1.1.1.9
	::= { pwCepEntry 9 }


-- End of CEP PW Table
-- Obtain index for PW CEP Configuration Table entries

pwCepCfgIndexNext OBJECT-TYPE
	SYNTAX  PwCfgIndexOrzero
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"This object contains an appropriate value to be used
		for pwCepCfgIndex when creating entries in the
		pwCepCfgTable.  The value 0 indicates that no
		unassigned entries are available.  To obtain the
		value of pwCepCfgIndex for a new entry in the
		pwCepCfgTable, the manager issues a management
		protocol retrieval operation to obtain the current
		value of pwCepCfgIndex.  After each retrieval
		operation, the agent should modify the value to
		reflect the next unassigned index.  After a manager
		retrieves a value, the agent will determine through
		its local policy when this index value will be made
		available for reuse."
	-- 1.3.6.1.2.1.200.1.2
	::= { pwCepObjects 2 }


-- CEP PW Configuration Table

pwCepCfgTable OBJECT-TYPE
	SYNTAX  SEQUENCE OF PwCepCfgEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"This table contains a set of parameters that may be
		referenced by one or more CEP PWs by pwCepTable."
	-- 1.3.6.1.2.1.200.1.3
	::= { pwCepObjects 3 }


pwCepCfgEntry OBJECT-TYPE
	SYNTAX  PwCepCfgEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"These parameters define the characteristics of a
		CEP PW.  They are grouped here to ease Network Management
		System (NMS) burden.  Once an entry is created here, it may
		be reused by many PWs.

		By default, all the read-create objects MUST NOT be
		changed after row activation unless specifically indicated
		in the individual object description.  If the operator
		wishes to change value of a read-create object, the
		pwCepCfgRowStatus MUST be set to notInService(2).

		The agent MUST NOT allow the change of the
		pwCepCfgRowStatus from the active(1) state for
		pwCepCfgEntry, which is in use by at least one active PW.

		Manual entries in this table SHOULD be preserved after a
		reboot, the agent MUST ensure the integrity of those
		entries.  If the set of entries of a specific row are found
		to be inconsistent after reboot, the affected PWs'
		pwOperStatus MUST be declared as notPresent(5)."
	INDEX {
		pwCepCfgTableIndex }
	-- 1.3.6.1.2.1.200.1.3.1
	::= { pwCepCfgTable 1 }


PwCepCfgEntry ::= SEQUENCE {

	pwCepCfgTableIndex           Unsigned32,
	pwCepSonetPayloadLength      Unsigned32,
	pwCepCfgMinPktLength         Unsigned32,
	pwCepCfgPktReorder           TruthValue,
	pwCepCfgEnableDBA            BITS,
	pwCepCfgRtpHdrSuppress       TruthValue,
	pwCepCfgJtrBfrDepth          Unsigned32,
	pwCepCfgConsecPktsInsync     Unsigned32,
	pwCepCfgConsecMissingOutSync Unsigned32,
	pwCepCfgPktErrorPlayOutValue Unsigned32,
	pwCepCfgMissingPktsToSes     Unsigned32,
	pwCepCfgSesToUas             Unsigned32,
	pwCepCfgSecsToExitUas        Unsigned32,
	pwCepCfgName                 SnmpAdminString,
	pwCepCfgRowStatus            RowStatus,
	pwCepCfgStorageType          StorageType }


pwCepCfgTableIndex OBJECT-TYPE
	SYNTAX  Unsigned32 (1..4294967295)
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"Primary index to this table."
	-- 1.3.6.1.2.1.200.1.3.1.1
	::= { pwCepCfgEntry 1 }


pwCepSonetPayloadLength OBJECT-TYPE
	SYNTAX  Unsigned32
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"The number of SONET bytes of the Path or VT carried as
		payload within one packet.  For example, for STS-1/VC-3 SPE
		circuits, a value of 783 bytes indicates that each packet
		carries the payload equivalent to one frame.  For VT1.5/VC11
		circuits, a payload length of 104 bytes indicates that each
		packet carries payload equivalent to one VT1.5 super-frame.
		The actual payload size may be different due to bandwidth
		reduction modes, e.g., Dynamic Bandwidth Allocation (DBA)
		mode or dynamically assigned fractional SPE.  This length
		applies to inbound and outbound packets carrying user
		payload.  Although there is no control over inbound packets,
		those of illegal length are discarded and accounted for (see
		pwCepPerf...Malformed.)







		The default values are determined by the pwCepType:
		783 for pwCepType equal to spe(2) or fracSpe(3).
		For vt(3) modes, the applicable super-frame payload size
		is the default value."
	REFERENCE
		"Malis, A., et al., 'Synchronous Optical Network/Synchronous
		Digital Hierarchy (SONET/SDH) Circuit Emulation over Packet
		(CEP)', RFC 4842, Sections 5.1 and 12.1"
	-- 1.3.6.1.2.1.200.1.3.1.2
	::= { pwCepCfgEntry 2 }


pwCepCfgMinPktLength OBJECT-TYPE
	SYNTAX  Unsigned32
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"This object defines the minimum CEP packet length in
		number of bytes (including CEP header and payload).
		It applies to CEP's bandwidth-savings packets.  Currently,
		DBA is the only bandwidth-savings packet type (in the
		future, CEP may support compression).  Minimum packet
		length is necessary in some systems or networks.

		Setting zero here indicates that there is no minimum
		packet restriction."
	DEFVAL { 0 }
	-- 1.3.6.1.2.1.200.1.3.1.3
	::= { pwCepCfgEntry 3 }


pwCepCfgPktReorder OBJECT-TYPE
	SYNTAX  TruthValue
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"This object defines if reordering is applied for incoming
		packets.

		If set 'true', as inbound packets are queued in the
		jitter buffer, out-of-order packets are reordered.  The
		maximum sequence number differential (i.e., the range in
		which resequencing can occur) is dependant on the depth
		of the jitter buffer.

		If the local agent supports packet reordering, the default
		value SHOULD be set to 'true'; otherwise, this value
		SHOULD be set to 'false'."
	-- 1.3.6.1.2.1.200.1.3.1.4
	::= { pwCepCfgEntry 4 }


pwCepCfgEnableDBA OBJECT-TYPE
	SYNTAX  BITS {
			ais(0),
			unequipped(1) }
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"This object defines when DBA is applied for packets sent
		toward the PSN.

		Setting 'ais' MUST cause CEP packet payload suppression
		when AIS is detected on the associated SONET path.
		Similarly, 'unequipped' MUST cause payload suppression
		when an unequipped condition is detected on the SONET/SDH
		PATH/VT.

		During DBA condition, CEP packets will continue
		to be sent, but with indicators set in the CEP header
		instructing the remote to play all ones (for AIS) or all
		zeros (for unequipped) onto its SONET/SDH path.

		NOTE: Some implementations may not support this feature.
		In these cases, this object should be read-only."
	REFERENCE
		"Malis, A., et al., 'Synchronous Optical Network/Synchronous
		Digital Hierarchy (SONET/SDH) Circuit Emulation over Packet
		(CEP)', RFC 4842, Section 11.1."
	-- 1.3.6.1.2.1.200.1.3.1.5
	::= { pwCepCfgEntry 5 }


pwCepCfgRtpHdrSuppress OBJECT-TYPE
	SYNTAX  TruthValue
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"If this object is set to 'true', an RTP header is not
		prepended to the CEP packet."
	REFERENCE
		"Malis, A., et al., 'Synchronous Optical Network/Synchronous
		Digital Hierarchy (SONET/SDH) Circuit Emulation over Packet
		(CEP)', RFC 4842, Section 5.3."
	DEFVAL { true }
	-- 1.3.6.1.2.1.200.1.3.1.6
	::= { pwCepCfgEntry 6 }


pwCepCfgJtrBfrDepth OBJECT-TYPE
	SYNTAX  Unsigned32
	UNITS	"micro-seconds"
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"This object defines the number of microseconds
		of expected packet delay variation for this CEP PW
		over the PSN.

		The actual jitter buffer MUST be at least twice this
		value for proper operation.

		If configured to a value not supported by the
		implementation, the agent MUST reject the SNMP Set
		operation."
	REFERENCE
		"The control of jitter and wander within digital
		networks which are based on the synchronous digital
		hierarchy (SDH), ITU-T Recommendation G.825."
	-- 1.3.6.1.2.1.200.1.3.1.7
	::= { pwCepCfgEntry 7 }


--
-- The following counters work together to integrate (filter)
-- errors and the lack of errors on the CEP PW.  An error is
-- caused by a missing packet.  Missing packets can be a result
-- of packet loss in the network, (uncorrectable) packet out
-- of sequence, packet-length error, jitter-buffer overflow,
-- and jitter-buffer underflow.  The result declares whether
-- or not the CEP PW is in Loss of Packet Sync (LOPS) state.
--

pwCepCfgConsecPktsInsync OBJECT-TYPE
	SYNTAX  Unsigned32
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"Consecutive packets with sequential sequence
		numbers required to exit the LOPS state."
	REFERENCE
		"Malis, A., et al., 'Synchronous Optical Network/Synchronous
		Digital Hierarchy (SONET/SDH) Circuit Emulation over Packet
		(CEP)', RFC 4842, Section 6.2.2."
	DEFVAL { 2 }
	-- 1.3.6.1.2.1.200.1.3.1.8
	::= { pwCepCfgEntry 8 }


pwCepCfgConsecMissingOutSync OBJECT-TYPE
	SYNTAX  Unsigned32
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"Consecutive missing packets required to enter
		the LOPS state."
	REFERENCE
		"Malis, A., et al., 'Synchronous Optical Network/Synchronous
		Digital Hierarchy (SONET/SDH) Circuit Emulation over Packet
		(CEP)', RFC 4842, Section 6.2.2."
	DEFVAL { 10 }
	-- 1.3.6.1.2.1.200.1.3.1.9
	::= { pwCepCfgEntry 9 }


pwCepCfgPktErrorPlayOutValue OBJECT-TYPE
	SYNTAX  Unsigned32 (0..255)
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"This object defines the value played when inbound packets
		have over/underflowed the jitter buffer or are missing
		for any reason.  This byte pattern is sent (played) on
		the SONET path."
	DEFVAL { 255 }
	-- Play all ones, equal to AIS indications
	-- 1.3.6.1.2.1.200.1.3.1.10
	::= { pwCepCfgEntry 10 }


pwCepCfgMissingPktsToSes OBJECT-TYPE
	SYNTAX  Unsigned32
	UNITS	"seconds"
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"The number of missing packets detected (consecutive or not)
		within a 1-second window to cause a Severely Errored
		Second (SES) to be counted."
	REFERENCE
		"Malis, A., et al., 'Synchronous Optical Network/Synchronous
		Digital Hierarchy (SONET/SDH) Circuit Emulation over Packet
		(CEP)', RFC 4842, Section 10.1."
	DEFVAL { 3 }
	-- 1.3.6.1.2.1.200.1.3.1.11
	::= { pwCepCfgEntry 11 }


pwCepCfgSesToUas OBJECT-TYPE
	SYNTAX  Unsigned32
	UNITS	"seconds"
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"The number of consecutive SESs before declaring PW in
		Unavailable Seconds (UAS) state (at which point
		pwCepPerfUASs starts counting).  The SesToUas default value
		is 10 seconds.

		NOTE: Similar to [RFC3592], if the agent chooses to update
		the various performance statistics in real time, it MUST
		be prepared to retroactively reduce the ES and SES counts by
		this value and increase the UAS count by this value when it
		determines that UAS state has been entered.

		NOTE: See pwCepPerfSESs and pwCepPerfUASs."
	REFERENCE
		"Malis, A., et al., 'Synchronous Optical Network/Synchronous
		Digital Hierarchy (SONET/SDH) Circuit Emulation over Packet
		(CEP)', RFC 4842, Section 10.1."
	DEFVAL { 10 }
	-- 1.3.6.1.2.1.200.1.3.1.12
	::= { pwCepCfgEntry 12 }


pwCepCfgSecsToExitUas OBJECT-TYPE
	SYNTAX  Unsigned32
	UNITS	"seconds"
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"The number of consecutive nonSESs before declaring PW is NOT
		in UAS state (at which point pwCepPerfUASs stops counting)."
	REFERENCE
		"Malis, A., et al., 'Synchronous Optical Network/Synchronous
		Digital Hierarchy (SONET/SDH) Circuit Emulation over Packet
		(CEP)', RFC 4842, Section 10.1."
	DEFVAL { 10 }
	-- 1.3.6.1.2.1.200.1.3.1.13
	::= { pwCepCfgEntry 13 }


pwCepCfgName OBJECT-TYPE
	SYNTAX  SnmpAdminString
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"This variable contains the name of the Configuration entry.
		This name may be used to help the NMS to display the
		purpose of the entry."
	-- 1.3.6.1.2.1.200.1.3.1.14
	::= { pwCepCfgEntry 14 }


pwCepCfgRowStatus OBJECT-TYPE
	SYNTAX  RowStatus
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"For creating, modifying, and deleting this row.

		None of the read-create objects' values can be changed
		when pwCepCfgRowStatus is in the active(1) state.  Changes
		are allowed when the pwRowStatus is in notInService(2) or
		notReady(3) states only.

		If the operator needs to change one of the values for an
		active row (for example, in order to fix a mismatch in
		configuration between the local node and the peer), the
		pwCepCfgRowStatus should be first changed to
		notInService(2).  The objects may be changed now and later
		changed to active(1) in order to re-initiate the signaling
		process with the new values in effect.

		Change of status from the active(1) state or deleting a row
		SHOULD be blocked by the local agent if the row is
		referenced by any pwCepEntry those pwRowStatus
		is in the active(1) state."
	-- 1.3.6.1.2.1.200.1.3.1.15
	::= { pwCepCfgEntry 15 }


pwCepCfgStorageType OBJECT-TYPE
	SYNTAX  StorageType
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"This object indicates the storage type for this row."
	DEFVAL { nonVolatile }
	-- 1.3.6.1.2.1.200.1.3.1.16
	::= { pwCepCfgEntry 16 }


-- End of CEP PW Configuration Parameter Table
-- CEP Fractional Table

pwCepFracTable OBJECT-TYPE
	SYNTAX  SEQUENCE OF PwCepFracEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"This table contains a set of parameters for CEP PWs with
		pwCepType FRAC type."
	-- 1.3.6.1.2.1.200.1.4
	::= { pwCepObjects 4 }


pwCepFracEntry OBJECT-TYPE
	SYNTAX  PwCepFracEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"There are two options for creating an entry in this table:

		- By the Element Management System (EMS) in advance for
		  creating the PW.
		- By the agent automatically when the PW is set up.

		The first option is typically used when there is a native
		service processing (NSP) cross-connect option between the
		physical ports and the emulated (virtual ports), while the
		second MAY be used when there is a one-to-one mapping
		between the emulated signal and the physical signal."
	INDEX {
		pwCepFracIndex }
	-- 1.3.6.1.2.1.200.1.4.1
	::= { pwCepFracTable 1 }


PwCepFracEntry ::= SEQUENCE {

	pwCepFracIndex          InterfaceIndex,
	pwCepFracMode           INTEGER,
	pwCepFracConfigError    BITS,
	pwCepFracAsync          PwCepFracAsyncMap,
	pwCepFracVtgMap         PwCepSonetVtgMap,
	pwCepFracEbm            PwCepSonetEbm,
	pwCepFracPeerEbm        PwCepSonetEbm,
	pwCepFracSdhVc4Mode     INTEGER,
	pwCepFracSdhVc4Tu3Map1  PwCepFracAsyncMap,
	pwCepFracSdhVc4Tu3Map2  PwCepFracAsyncMap,
	pwCepFracSdhVc4Tu3Map3  PwCepFracAsyncMap,
	pwCepFracSdhVc4Tug2Map1 PwCepSonetVtgMap,
	pwCepFracSdhVc4Tug2Map2 PwCepSonetVtgMap,
	pwCepFracSdhVc4Tug2Map3 PwCepSonetVtgMap,
	pwCepFracSdhVc4Ebm1     PwCepSdhVc4Ebm,
	pwCepFracSdhVc4Ebm2     PwCepSdhVc4Ebm,
	pwCepFracSdhVc4Ebm3     PwCepSdhVc4Ebm,
	pwCepFracSdhVc4PeerEbm1 PwCepSdhVc4Ebm,
	pwCepFracSdhVc4PeerEbm2 PwCepSdhVc4Ebm,
	pwCepFracSdhVc4PeerEbm3 PwCepSdhVc4Ebm,
	pwCepFracRowStatus      RowStatus,
	pwCepFracStorageType    StorageType }


pwCepFracIndex OBJECT-TYPE
	SYNTAX  InterfaceIndex
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"This is the index of this table.  It is a unique
		index within the ifTable.  It represents the interface index
		for the SONET path ([RFC3592], Section 3.3) for fractional
		SPE emulation.

		It may represent an internal (virtual) interface if an NSP
		function exists between the physical interface and the
		emulation process."
	-- 1.3.6.1.2.1.200.1.4.1.1
	::= { pwCepFracEntry 1 }


pwCepFracMode OBJECT-TYPE
	SYNTAX  INTEGER {
			notApplicable(1),
			dynamic(2),
			static(3),
			staticWithEbm(4),
			staticAsync(5) }
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"Fractional mode for STS-1/VC-3 or VC-4 circuits:

		notApplicable - When this object is not applicable.
		dynamic - EBM carried within the CEP header.  Unequipped
		          VTs are removed from the payload on the fly.
		static  - EBM not carried within the CEP header.  Only VTs
		          defined in the EBM are carried within the payload.
		staticWithEbm - EBM carried within the CEP header.  Only
		          VTs defined in the EBM are carried within the
		          payload.
		staticAsync - Asynchronous E3/T3 fixed byte removal only."
	DEFVAL { dynamic }
	-- 1.3.6.1.2.1.200.1.4.1.2
	::= { pwCepFracEntry 2 }


pwCepFracConfigError OBJECT-TYPE
	SYNTAX  BITS {
			other(0),
			vtgMapEbmConflict(1),
			vtgMapAsyncConflict(2) }
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"vtgMapEbmConflict(1) is set when the configured static EBM
		does not match the configured vtgMap for fractional
		STS-1/VC-3 circuits or when the TUG2Map is in conflict with
		the static EBM for VC-4 circuits, for example, if the vtgMap
		specifies that VTG#1 carries VT2 VTs while the EBM indicate
		that four VTs are equipped within VTG#1.

		vtgMapAsyncConflict(2) is set when there is a conflict
		between the mode, the async indication, and the vtgMap
		fields.  For example, fractional mode is set to staticAsync
		while the VtgMap indicates that the STS-1/VC-3 carries VTs,
		or both async1 and Tug2Map are set in fractional VC-4
		circuits."
	-- 1.3.6.1.2.1.200.1.4.1.3
	::= { pwCepFracEntry 3 }


pwCepFracAsync OBJECT-TYPE
	SYNTAX  PwCepFracAsyncMap
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"This object defines the asynchronous payload carried
		within the STS-1/VC-3.  This object is applicable when
		pwCepFracMode equals 'staticAsync' and MUST equal to
		'other' otherwise."
	DEFVAL { other }
	-- 1.3.6.1.2.1.200.1.4.1.4
	::= { pwCepFracEntry 4 }


pwCepFracVtgMap OBJECT-TYPE
	SYNTAX  PwCepSonetVtgMap
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"This object defines the VT/VC types of the seven
		VTG/TUG-2 within the STS-1/VC-3.

		This variable should be set when 'dynamic', 'static',
		or 'staticWithEbm' fractional STS-1/VC-3 pwCepFracMode
		is selected."
	-- 1.3.6.1.2.1.200.1.4.1.5
	::= { pwCepFracEntry 5 }


pwCepFracEbm OBJECT-TYPE
	SYNTAX  PwCepSonetEbm
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"This object holds the static Equipped Bit Mask (EBM)
		for STS-1/VC-3 channel.

		This variable MAY be set when 'static' or
		'staticWithEbm' fractional STS-1/VC-3 pwCepFracMode is
		selected.

		It is possible that the configuration of other MIB modules
		will define the EBM value; in these cases, this object is
		read-only and reflects the actual EBM that would be used."
	-- 1.3.6.1.2.1.200.1.4.1.6
	::= { pwCepFracEntry 6 }


pwCepFracPeerEbm OBJECT-TYPE
	SYNTAX  PwCepSonetEbm
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"This object reports the Equipped Bit Mask (EBM) for
		STS-1/VC-3 channel as received from the peer within
		the CEP extension header."
	-- 1.3.6.1.2.1.200.1.4.1.7
	::= { pwCepFracEntry 7 }


pwCepFracSdhVc4Mode OBJECT-TYPE
	SYNTAX  INTEGER {
			notApplicable(1),
			dynamic(2),
			static(3),
			staticWithEbm(4) }
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"Fractional mode for VC-4 circuits:

		notApplicable - When this is not VC-4 circuit.
		dynamic - EBM carried within the CEP header.  Unequipped
		          VTs are removed from the payload on the fly.
		static  - EBM not carried within the CEP header.  Only VTs
		          defined in the EBM are carried within the payload.
		staticWithEbm - EBM carried within the CEP header.  Only
		          VTs defined in the EBM are carried within the
		          payload."
	DEFVAL { notApplicable }
	-- 1.3.6.1.2.1.200.1.4.1.8
	::= { pwCepFracEntry 8 }


pwCepFracSdhVc4Tu3Map1 OBJECT-TYPE
	SYNTAX  PwCepFracAsyncMap
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"The type of asynchronous mapping carried inside STS-1,
		VC-3, or TUG-3 containing TU-3 circuit."
	DEFVAL { other }
	-- 1.3.6.1.2.1.200.1.4.1.9
	::= { pwCepFracEntry 9 }


pwCepFracSdhVc4Tu3Map2 OBJECT-TYPE
	SYNTAX  PwCepFracAsyncMap
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"If the second TUG-3 within the VC-4 contains a TU-3, this
		variable must be set."
	DEFVAL { other }
	-- 1.3.6.1.2.1.200.1.4.1.10
	::= { pwCepFracEntry 10 }


pwCepFracSdhVc4Tu3Map3 OBJECT-TYPE
	SYNTAX  PwCepFracAsyncMap
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"If the third TUG-3 within the VC-4 contains a TU-3, this
		variable must be set."
	DEFVAL { other }
	-- 1.3.6.1.2.1.200.1.4.1.11
	::= { pwCepFracEntry 11 }


pwCepFracSdhVc4Tug2Map1 OBJECT-TYPE
	SYNTAX  PwCepSonetVtgMap
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"The VC types of the seven TUG-2s within the first
		TUG-3 of the VC-4."
	-- 1.3.6.1.2.1.200.1.4.1.12
	::= { pwCepFracEntry 12 }


pwCepFracSdhVc4Tug2Map2 OBJECT-TYPE
	SYNTAX  PwCepSonetVtgMap
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"The VC types of the seven TUG-2s within the second
		TUG-3 of the VC-4."
	-- 1.3.6.1.2.1.200.1.4.1.13
	::= { pwCepFracEntry 13 }


pwCepFracSdhVc4Tug2Map3 OBJECT-TYPE
	SYNTAX  PwCepSonetVtgMap
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"The VC types of the seven TUG-2s within the third
		TUG-3 of the VC-4."
	-- 1.3.6.1.2.1.200.1.4.1.14
	::= { pwCepFracEntry 14 }


pwCepFracSdhVc4Ebm1 OBJECT-TYPE
	SYNTAX  PwCepSdhVc4Ebm
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"Static Equipped Bit Mask (EBM) for the first TUG-3
		within the VC-4.

		This variable should be set when 'static' or
		'staticWithEbm' fractional VC-4 pwCepFracMode is
		selected.







		It is possible that the EBM that would be used is
		available based on configuration of other MIB modules.
		In these cases, this object is read-only and reflects the
		actual EBM that would be used."
	-- 1.3.6.1.2.1.200.1.4.1.15
	::= { pwCepFracEntry 15 }


pwCepFracSdhVc4Ebm2 OBJECT-TYPE
	SYNTAX  PwCepSdhVc4Ebm
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"Static Equipped Bit Mask (EBM) for the second TUG-3
		within the VC-4.

		This variable should be set when 'static' or
		'staticWithEbm' fractional VC-4 pwCepFracMode is
		selected.

		It is possible that the EBM that would be used is
		available based on configuration of other MIB modules.
		In these cases, this object is read-only and reflects the
		actual EBM that would be used."
	-- 1.3.6.1.2.1.200.1.4.1.16
	::= { pwCepFracEntry 16 }


pwCepFracSdhVc4Ebm3 OBJECT-TYPE
	SYNTAX  PwCepSdhVc4Ebm
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"Static Equipped Bit Mask (EBM) for the third TUG-3 within
		the VC-4.

		This variable should be set when 'Static' or
		'staticWithEbm' fractional VC-4 pwCepFracMode is
		selected.

		It is possible that the EBM that would be used is
		available based on configuration of other MIB modules.
		In these cases, this object is read-only and reflects the
		actual EBM that would be used."
	-- 1.3.6.1.2.1.200.1.4.1.17
	::= { pwCepFracEntry 17 }


pwCepFracSdhVc4PeerEbm1 OBJECT-TYPE
	SYNTAX  PwCepSdhVc4Ebm
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Equipped Bit Mask (EBM) for the first TUG-3 within
		the fractional VC-4 channel received from the peer
		within the CEP extension header."
	-- 1.3.6.1.2.1.200.1.4.1.18
	::= { pwCepFracEntry 18 }


pwCepFracSdhVc4PeerEbm2 OBJECT-TYPE
	SYNTAX  PwCepSdhVc4Ebm
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Equipped Bit Mask (EBM) for the second TUG-3 within
		the fractional VC-4 channel received from the peer
		within the CEP extension header."
	-- 1.3.6.1.2.1.200.1.4.1.19
	::= { pwCepFracEntry 19 }


pwCepFracSdhVc4PeerEbm3 OBJECT-TYPE
	SYNTAX  PwCepSdhVc4Ebm
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Equipped Bit Mask (EBM) for the third TUG-3 within
		the fractional VC-4 channel received from the peer
		within the CEP extension header."
	-- 1.3.6.1.2.1.200.1.4.1.20
	::= { pwCepFracEntry 20 }


pwCepFracRowStatus OBJECT-TYPE
	SYNTAX  RowStatus
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"For creating, modifying, and deleting this row.
		This object MAY be changed at any time."
	-- 1.3.6.1.2.1.200.1.4.1.21
	::= { pwCepFracEntry 21 }


pwCepFracStorageType OBJECT-TYPE
	SYNTAX  StorageType
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"This variable indicates the storage type for this
		object."
	DEFVAL { nonVolatile }
	-- 1.3.6.1.2.1.200.1.4.1.22
	::= { pwCepFracEntry 22 }


-- End CEP Fractional Table
-- CEP PW Performance Current Interval Table

pwCepPerfCurrentTable OBJECT-TYPE
	SYNTAX  SEQUENCE OF PwCepPerfCurrentEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"CEP bridges the SONET and packet worlds.  In the packet
		world, counts typically start from the time of service
		creation and do not stop.  In the SONET world, counts are
		kept in 15-minute intervals.  The PW CEP MIB supports both
		methods.  The current 15-minute interval counts are in
		this table.  The interval and total stats are in tables
		following this.

		This table provides per-CEP PW performance information.
		High capacity (HC) counters are required for some counts
		due to the high speeds expected with CEP services.  A SONET
		path of width 48 (STS-48c) can rollover non-HC counters in
		a few minutes."
	-- 1.3.6.1.2.1.200.1.5
	::= { pwCepObjects 5 }


pwCepPerfCurrentEntry OBJECT-TYPE
	SYNTAX  PwCepPerfCurrentEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"An entry in this table is created by the agent for every
		pwCep entry.  After 15 minutes, the contents of this table
		entry are copied to a new entry in the pwCepPerfInterval
		table, and the counts in this entry are reset to zero."
	INDEX {
		pwIndex }
	-- 1.3.6.1.2.1.200.1.5.1
	::= { pwCepPerfCurrentTable 1 }


PwCepPerfCurrentEntry ::= SEQUENCE {

	pwCepPerfCurrentDbaInPacketsHC   HCPerfCurrentCount,
	pwCepPerfCurrentDbaOutPacketsHC  HCPerfCurrentCount,
	pwCepPerfCurrentInNegPtrAdjust   PerfCurrentCount,
	pwCepPerfCurrentInPosPtrAdjust   PerfCurrentCount,
	pwCepPerfCurrentInPtrAdjustSecs  PerfCurrentCount,
	pwCepPerfCurrentOutNegPtrAdjust  PerfCurrentCount,
	pwCepPerfCurrentOutPosPtrAdjust  PerfCurrentCount,
	pwCepPerfCurrentOutPtrAdjustSecs PerfCurrentCount,
	pwCepPerfCurrentAbsPtrAdjust     Integer32,
	pwCepPerfCurrentMissingPkts      PerfCurrentCount,
	pwCepPerfCurrentPktsOoseq        PerfCurrentCount,
	pwCepPerfCurrentPktsOoRngDropped PerfCurrentCount,
	pwCepPerfCurrentJtrBfrUnderruns  PerfCurrentCount,
	pwCepPerfCurrentPktsMalformed    PerfCurrentCount,
	pwCepPerfCurrentSummaryErrors    PerfCurrentCount,
	pwCepPerfCurrentESs              PerfCurrentCount,
	pwCepPerfCurrentSESs             PerfCurrentCount,
	pwCepPerfCurrentUASs             PerfCurrentCount,
	pwCepPerfCurrentFC               PerfCurrentCount }


pwCepPerfCurrentDbaInPacketsHC OBJECT-TYPE
	SYNTAX  HCPerfCurrentCount
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Number of DBA packets received."
	-- 1.3.6.1.2.1.200.1.5.1.1
	::= { pwCepPerfCurrentEntry 1 }


pwCepPerfCurrentDbaOutPacketsHC OBJECT-TYPE
	SYNTAX  HCPerfCurrentCount
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Number of DBA packets sent."
	-- 1.3.6.1.2.1.200.1.5.1.2
	::= { pwCepPerfCurrentEntry 2 }


-- Pointer adjustment stats

pwCepPerfCurrentInNegPtrAdjust OBJECT-TYPE
	SYNTAX  PerfCurrentCount
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Number of negative pointer adjustments sent on the
		SONET path based on CEP pointer adjustments received."
	-- 1.3.6.1.2.1.200.1.5.1.3
	::= { pwCepPerfCurrentEntry 3 }


pwCepPerfCurrentInPosPtrAdjust OBJECT-TYPE
	SYNTAX  PerfCurrentCount
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Number of positive pointer adjustments sent on the
		SONET path based on CEP pointer adjustments received."
	-- 1.3.6.1.2.1.200.1.5.1.4
	::= { pwCepPerfCurrentEntry 4 }


pwCepPerfCurrentInPtrAdjustSecs OBJECT-TYPE
	SYNTAX  PerfCurrentCount
	UNITS	"seconds"
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Number of seconds in which a positive or negative pointer
		adjustment was sent on the SONET path."
	-- 1.3.6.1.2.1.200.1.5.1.5
	::= { pwCepPerfCurrentEntry 5 }


pwCepPerfCurrentOutNegPtrAdjust OBJECT-TYPE
	SYNTAX  PerfCurrentCount
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Number of negative pointer adjustments seen on the
		SONET path and encoded onto sent CEP packets."
	-- 1.3.6.1.2.1.200.1.5.1.6
	::= { pwCepPerfCurrentEntry 6 }


pwCepPerfCurrentOutPosPtrAdjust OBJECT-TYPE
	SYNTAX  PerfCurrentCount
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Number of positive pointer adjustments seen on the
		SONET path and encoded onto sent CEP packets."
	-- 1.3.6.1.2.1.200.1.5.1.7
	::= { pwCepPerfCurrentEntry 7 }


pwCepPerfCurrentOutPtrAdjustSecs OBJECT-TYPE
	SYNTAX  PerfCurrentCount
	UNITS	"seconds"
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Number of seconds in which a positive or negative pointer
		adjustment was seen on the SONET path."
	-- 1.3.6.1.2.1.200.1.5.1.8
	::= { pwCepPerfCurrentEntry 8 }


pwCepPerfCurrentAbsPtrAdjust OBJECT-TYPE
	SYNTAX  Integer32
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Indicates the relative adjustment drift between
		inbound and outbound streams.

		It is calculated as absolute value of:
		   (InPosPtrAdjust  -   InNegPtrAdjust ) -
		   (OutPosPtrAdjust  -   OutNegPtrAdjust)"
	-- 1.3.6.1.2.1.200.1.5.1.9
	::= { pwCepPerfCurrentEntry 9 }


pwCepPerfCurrentMissingPkts OBJECT-TYPE
	SYNTAX  PerfCurrentCount
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Number of missing packets (as detected via CEP header
		sequence number gaps)."
	-- 1.3.6.1.2.1.200.1.5.1.10
	::= { pwCepPerfCurrentEntry 10 }


pwCepPerfCurrentPktsOoseq OBJECT-TYPE
	SYNTAX  PerfCurrentCount
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Number of packets detected out of sequence (via CEP
		header sequence numbers) but successfully reordered.
		Note: Some implementations may not support this
		feature (see pwCepCfgPktReorder)."
	-- 1.3.6.1.2.1.200.1.5.1.11
	::= { pwCepPerfCurrentEntry 11 }


pwCepPerfCurrentPktsOoRngDropped OBJECT-TYPE
	SYNTAX  PerfCurrentCount
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Number of packets detected out of range (via CEP header
		sequence numbers) and could not be reordered or could not
		fit in the jitter buffer."
	-- 1.3.6.1.2.1.200.1.5.1.12
	::= { pwCepPerfCurrentEntry 12 }


pwCepPerfCurrentJtrBfrUnderruns OBJECT-TYPE
	SYNTAX  PerfCurrentCount
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Number of times a packet needed to be played out and the
		jitter buffer was empty."
	-- 1.3.6.1.2.1.200.1.5.1.13
	::= { pwCepPerfCurrentEntry 13 }


pwCepPerfCurrentPktsMalformed OBJECT-TYPE
	SYNTAX  PerfCurrentCount
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Number of packets detected with unexpected size or bad
		headers stack."
	-- 1.3.6.1.2.1.200.1.5.1.14
	::= { pwCepPerfCurrentEntry 14 }


pwCepPerfCurrentSummaryErrors OBJECT-TYPE
	SYNTAX  PerfCurrentCount
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"A summary of all the packet-error types above (from
		missing packets to bad length packets)."
	-- 1.3.6.1.2.1.200.1.5.1.15
	::= { pwCepPerfCurrentEntry 15 }


pwCepPerfCurrentESs OBJECT-TYPE
	SYNTAX  PerfCurrentCount
	UNITS	"seconds"
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The counter associated with the number of Errored
		Seconds encountered."
	-- 1.3.6.1.2.1.200.1.5.1.16
	::= { pwCepPerfCurrentEntry 16 }


pwCepPerfCurrentSESs OBJECT-TYPE
	SYNTAX  PerfCurrentCount
	UNITS	"seconds"
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The counter associated with the number of
		Severely Errored Seconds encountered."
	-- 1.3.6.1.2.1.200.1.5.1.17
	::= { pwCepPerfCurrentEntry 17 }


pwCepPerfCurrentUASs OBJECT-TYPE
	SYNTAX  PerfCurrentCount
	UNITS	"seconds"
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The counter associated with the number of
		Unavailable Seconds encountered."
	-- 1.3.6.1.2.1.200.1.5.1.18
	::= { pwCepPerfCurrentEntry 18 }


pwCepPerfCurrentFC OBJECT-TYPE
	SYNTAX  PerfCurrentCount
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"CEP Failure Counts (FC-CEP).  The number of CEP failure
		events.  A failure event begins when the LOPS failure
		is declared and ends when the failure is cleared.  A
		failure event that begins in one period and ends in
		another period is counted only in the period in which
		it begins."
	-- 1.3.6.1.2.1.200.1.5.1.19
	::= { pwCepPerfCurrentEntry 19 }


-- End CEP PW Performance Current Interval Table
-- CEP Performance 15-Minute Interval Table

pwCepPerfIntervalTable OBJECT-TYPE
	SYNTAX  SEQUENCE OF PwCepPerfIntervalEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"This table provides per-CEP PW performance information,
		much like the pwCepPerfCurrentTable above.  However,
		these counts represent historical 15-minute intervals.
		Typically, this table will have a maximum of 96 entries
		for a 24-hour period but is not limited to this.

		NOTE: Counter64 objects are used here; Counter32 is
		too small for OC-768 CEP PWs."
	-- 1.3.6.1.2.1.200.1.6
	::= { pwCepObjects 6 }


pwCepPerfIntervalEntry OBJECT-TYPE
	SYNTAX  PwCepPerfIntervalEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"An entry in this table is created by the agent for
		every pwCepPerfCurrentEntry that is 15 minutes old.
		The contents of the Current entry are copied to the new







		entry here.  The Current entry then resets its counts
		to zero for the next current 15-minute interval.
		pwCepIndex is found in the pwCepCfg table."
	INDEX {
		pwIndex,
		pwCepPerfIntervalNumber }
	-- 1.3.6.1.2.1.200.1.6.1
	::= { pwCepPerfIntervalTable 1 }


PwCepPerfIntervalEntry ::= SEQUENCE {

	pwCepPerfIntervalNumber           Integer32,
	pwCepPerfIntervalValidData        TruthValue,
	pwCepPerfIntervalReset            INTEGER,
	pwCepPerfIntervalTimeElapsed      HCPerfTimeElapsed,
	pwCepPerfIntervalDbaInPacketsHC   HCPerfIntervalCount,
	pwCepPerfIntervalDbaOutPacketsHC  HCPerfIntervalCount,
	pwCepPerfIntervalInNegPtrAdjust   PerfIntervalCount,
	pwCepPerfIntervalInPosPtrAdjust   PerfIntervalCount,
	pwCepPerfIntervalInPtrAdjustSecs  PerfIntervalCount,
	pwCepPerfIntervalOutNegPtrAdjust  PerfIntervalCount,
	pwCepPerfIntervalOutPosPtrAdjust  PerfIntervalCount,
	pwCepPerfIntervalOutPtrAdjustSecs PerfIntervalCount,
	pwCepPerfIntervalAbsPtrAdjust     Integer32,
	pwCepPerfIntervalMissingPkts      PerfIntervalCount,
	pwCepPerfIntervalPktsOoseq        PerfIntervalCount,
	pwCepPerfIntervalPktsOoRngDropped PerfIntervalCount,
	pwCepPerfIntervalJtrBfrUnderruns  PerfIntervalCount,
	pwCepPerfIntervalPktsMalformed    PerfIntervalCount,
	pwCepPerfIntervalSummaryErrors    PerfIntervalCount,
	pwCepPerfIntervalESs              PerfIntervalCount,
	pwCepPerfIntervalSESs             PerfIntervalCount,
	pwCepPerfIntervalUASs             PerfIntervalCount,
	pwCepPerfIntervalFC               PerfIntervalCount }


pwCepPerfIntervalNumber OBJECT-TYPE
	SYNTAX  Integer32 (1..96)
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"A number (between 1 and 96 to cover a 24-hour
		period) that identifies the interval for which the set
		of statistics is available.  The interval identified by 1
		is the most recently completed 15-minute interval, and





		the interval identified by N is the interval immediately
		preceding the one identified by N-1.  The minimum range of
		N is 1 through 4.  The default range is 1 through 32.  The
		maximum range of N is 1 through 96."
	-- 1.3.6.1.2.1.200.1.6.1.1
	::= { pwCepPerfIntervalEntry 1 }


pwCepPerfIntervalValidData OBJECT-TYPE
	SYNTAX  TruthValue
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"This variable indicates if the data for this interval
		is valid."
	-- 1.3.6.1.2.1.200.1.6.1.2
	::= { pwCepPerfIntervalEntry 2 }


pwCepPerfIntervalReset OBJECT-TYPE
	SYNTAX  INTEGER {
			reset(1),
			normal(2) }
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"Used in cases where the user knows that the errors
		within this interval should not be counted.  Writing
		'reset' sets all error counts to zero.  The value of
		0 is not used here due to issues with
		implementations."
	-- 1.3.6.1.2.1.200.1.6.1.3
	::= { pwCepPerfIntervalEntry 3 }


pwCepPerfIntervalTimeElapsed OBJECT-TYPE
	SYNTAX  HCPerfTimeElapsed
	UNITS	"seconds"
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The duration of a particular interval in seconds.
		Adjustments in the system's time-of-day clock may
		cause the interval to be greater or less than the
		normal value.  Therefore, this actual interval value
		is provided."
	-- 1.3.6.1.2.1.200.1.6.1.4
	::= { pwCepPerfIntervalEntry 4 }


pwCepPerfIntervalDbaInPacketsHC OBJECT-TYPE
	SYNTAX  HCPerfIntervalCount
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Number of DBA packets received."
	-- 1.3.6.1.2.1.200.1.6.1.5
	::= { pwCepPerfIntervalEntry 5 }


pwCepPerfIntervalDbaOutPacketsHC OBJECT-TYPE
	SYNTAX  HCPerfIntervalCount
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Number of DBA packets sent."
	-- 1.3.6.1.2.1.200.1.6.1.6
	::= { pwCepPerfIntervalEntry 6 }


-- Pointer adjustment stats

pwCepPerfIntervalInNegPtrAdjust OBJECT-TYPE
	SYNTAX  PerfIntervalCount
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Number of negative pointer adjustments sent on the
		SONET path based on CEP pointer adjustments received."
	-- 1.3.6.1.2.1.200.1.6.1.7
	::= { pwCepPerfIntervalEntry 7 }


pwCepPerfIntervalInPosPtrAdjust OBJECT-TYPE
	SYNTAX  PerfIntervalCount
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Number of positive pointer adjustments sent on the
		SONET path based on CEP pointer adjustments received."
	-- 1.3.6.1.2.1.200.1.6.1.8
	::= { pwCepPerfIntervalEntry 8 }


pwCepPerfIntervalInPtrAdjustSecs OBJECT-TYPE
	SYNTAX  PerfIntervalCount
	UNITS	"seconds"
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Number of seconds in which a positive or negative
		pointer adjustment was sent on the SONET path."
	-- 1.3.6.1.2.1.200.1.6.1.9
	::= { pwCepPerfIntervalEntry 9 }


pwCepPerfIntervalOutNegPtrAdjust OBJECT-TYPE
	SYNTAX  PerfIntervalCount
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Number of negative pointer adjustments seen on the
		SONET path and encoded onto sent CEP packets."
	-- 1.3.6.1.2.1.200.1.6.1.10
	::= { pwCepPerfIntervalEntry 10 }


pwCepPerfIntervalOutPosPtrAdjust OBJECT-TYPE
	SYNTAX  PerfIntervalCount
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Number of positive pointer adjustments seen on the
		SONET path and encoded onto sent CEP packets."
	-- 1.3.6.1.2.1.200.1.6.1.11
	::= { pwCepPerfIntervalEntry 11 }


pwCepPerfIntervalOutPtrAdjustSecs OBJECT-TYPE
	SYNTAX  PerfIntervalCount
	UNITS	"seconds"
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Number of seconds in which a positive or negative
		pointer adjustment was seen on the SONET path."
	-- 1.3.6.1.2.1.200.1.6.1.12
	::= { pwCepPerfIntervalEntry 12 }


pwCepPerfIntervalAbsPtrAdjust OBJECT-TYPE
	SYNTAX  Integer32
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The relative adjustment drift between inbound
		and outbound streams.

		It is calculated as absolute value of:
		   (InPosPtrAdjust  -   InNegPtrAdjust) -
		   (OutPosPtrAdjust  -  OutNegPtrAdjust)"
	-- 1.3.6.1.2.1.200.1.6.1.13
	::= { pwCepPerfIntervalEntry 13 }


pwCepPerfIntervalMissingPkts OBJECT-TYPE
	SYNTAX  PerfIntervalCount
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Number of missing packets (as detected via CEP header
		sequence number gaps)."
	-- 1.3.6.1.2.1.200.1.6.1.14
	::= { pwCepPerfIntervalEntry 14 }


pwCepPerfIntervalPktsOoseq OBJECT-TYPE
	SYNTAX  PerfIntervalCount
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Number of packets detected out of sequence (via CEP
		header sequence numbers) but successfully reordered.
		Note: Some implementations mat not support this
		feature (see pwCepCfgPktReorder)."
	-- 1.3.6.1.2.1.200.1.6.1.15
	::= { pwCepPerfIntervalEntry 15 }


pwCepPerfIntervalPktsOoRngDropped OBJECT-TYPE
	SYNTAX  PerfIntervalCount
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Number of packets detected out of range (via CEP
		header sequence numbers) and could not be reordered
		or could not fit in the jitter buffer."
	-- 1.3.6.1.2.1.200.1.6.1.16
	::= { pwCepPerfIntervalEntry 16 }


pwCepPerfIntervalJtrBfrUnderruns OBJECT-TYPE
	SYNTAX  PerfIntervalCount
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Number of times a packet needed to be played
		out and the jitter buffer was empty."
	-- 1.3.6.1.2.1.200.1.6.1.17
	::= { pwCepPerfIntervalEntry 17 }


pwCepPerfIntervalPktsMalformed OBJECT-TYPE
	SYNTAX  PerfIntervalCount
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Number of packets detected with unexpected size or bad
		headers stack."
	-- 1.3.6.1.2.1.200.1.6.1.18
	::= { pwCepPerfIntervalEntry 18 }


pwCepPerfIntervalSummaryErrors OBJECT-TYPE
	SYNTAX  PerfIntervalCount
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"A summary of all the packet-error types above (from
		missing packets to bad length packets)."
	-- 1.3.6.1.2.1.200.1.6.1.19
	::= { pwCepPerfIntervalEntry 19 }


pwCepPerfIntervalESs OBJECT-TYPE
	SYNTAX  PerfIntervalCount
	UNITS	"seconds"
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The counter associated with the number of Errored
		Seconds encountered."
	-- 1.3.6.1.2.1.200.1.6.1.20
	::= { pwCepPerfIntervalEntry 20 }


pwCepPerfIntervalSESs OBJECT-TYPE
	SYNTAX  PerfIntervalCount
	UNITS	"seconds"
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The counter associated with the number of
		Severely Errored Seconds encountered."
	-- 1.3.6.1.2.1.200.1.6.1.21
	::= { pwCepPerfIntervalEntry 21 }


pwCepPerfIntervalUASs OBJECT-TYPE
	SYNTAX  PerfIntervalCount
	UNITS	"seconds"
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The counter associated with the number of
		Unavailable Seconds encountered."
	-- 1.3.6.1.2.1.200.1.6.1.22
	::= { pwCepPerfIntervalEntry 22 }


pwCepPerfIntervalFC OBJECT-TYPE
	SYNTAX  PerfIntervalCount
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"CEP Failure Counts (FC-CEP).  The number of CEP failure
		events.  A failure event begins when the LOPS failure
		is declared and ends when the failure is cleared.  A
		failure event that begins in one period and ends in
		another period is counted only in the period in which
		it begins."
	-- 1.3.6.1.2.1.200.1.6.1.23
	::= { pwCepPerfIntervalEntry 23 }


-- End CEP Performance 15-Minute Interval Table
-- CEP Performance 1-Day Table

pwCepPerf1DayIntervalTable OBJECT-TYPE
	SYNTAX  SEQUENCE OF PwCepPerf1DayIntervalEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"This table provides per CEP PW performance information,
		the current day's measurement, and the previous day's
		interval.

		In the extreme case where one of the error counters has
		overflowed during the one-day interval, the error counter
		MUST NOT wrap around and MUST return the maximum value."
	-- 1.3.6.1.2.1.200.1.7
	::= { pwCepObjects 7 }


pwCepPerf1DayIntervalEntry OBJECT-TYPE
	SYNTAX  PwCepPerf1DayIntervalEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"An entry is created in this table by the agent for
		every entry in the pwCepTable and for each day
		interval up to the number of supported historical
		intervals."
	INDEX {
		pwIndex,
		pwCepPerf1DayIntervalNumber }
	-- 1.3.6.1.2.1.200.1.7.1
	::= { pwCepPerf1DayIntervalTable 1 }


PwCepPerf1DayIntervalEntry ::= SEQUENCE {

	pwCepPerf1DayIntervalNumber           Unsigned32,
	pwCepPerf1DayIntervalValidData        TruthValue,
	pwCepPerf1DayIntervalMoniSecs         HCPerfTimeElapsed,
	pwCepPerf1DayIntervalDbaInPacketsHC   Counter64,
	pwCepPerf1DayIntervalDbaOutPacketsHC  Counter64,
	pwCepPerf1DayIntervalInNegPtrAdjust   Counter32,
	pwCepPerf1DayIntervalInPosPtrAdjust   Counter32,
	pwCepPerf1DayIntervalInPtrAdjustSecs  Counter32,
	pwCepPerf1DayIntervalOutNegPtrAdjust  Counter32,
	pwCepPerf1DayIntervalOutPosPtrAdjust  Counter32,
	pwCepPerf1DayIntervalOutPtrAdjustSecs Counter32,
	pwCepPerf1DayIntervalAbsPtrAdjust     Integer32,
	pwCepPerf1DayIntervalMissingPkts      Counter32,
	pwCepPerf1DayIntervalPktsOoseq        Counter32,
	pwCepPerf1DayIntervalPktsOoRngDropped Counter32,
	pwCepPerf1DayIntervalJtrBfrUnderruns  Counter32,
	pwCepPerf1DayIntervalPktsMalformed    Counter32,
	pwCepPerf1DayIntervalSummaryErrors    Counter32,
	pwCepPerf1DayIntervalESs              Counter32,
	pwCepPerf1DayIntervalSESs             Counter32,
	pwCepPerf1DayIntervalUASs             Counter32,
	pwCepPerf1DayIntervalFC               Counter32 }


pwCepPerf1DayIntervalNumber OBJECT-TYPE
	SYNTAX  Unsigned32 (1..31)
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"History Data Interval number.  Interval 1 is the current day
		measurement period; interval 2 is the most recent previous
		day; and interval 30 is 31 days ago."
	-- 1.3.6.1.2.1.200.1.7.1.1
	::= { pwCepPerf1DayIntervalEntry 1 }


pwCepPerf1DayIntervalValidData OBJECT-TYPE
	SYNTAX  TruthValue
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"This variable indicates if the data for this interval
		is valid."
	-- 1.3.6.1.2.1.200.1.7.1.2
	::= { pwCepPerf1DayIntervalEntry 2 }


pwCepPerf1DayIntervalMoniSecs OBJECT-TYPE
	SYNTAX  HCPerfTimeElapsed
	UNITS	"seconds"
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The amount of time in the 1-day interval over which the
		performance monitoring information is actually counted.
		This value will be the same as the interval duration except
		in situations where performance monitoring data could not
		be collected for any reason or the agent clock was
		adjusted."
	-- 1.3.6.1.2.1.200.1.7.1.3
	::= { pwCepPerf1DayIntervalEntry 3 }


pwCepPerf1DayIntervalDbaInPacketsHC OBJECT-TYPE
	SYNTAX  Counter64
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Number of DBA packets received."
	-- 1.3.6.1.2.1.200.1.7.1.4
	::= { pwCepPerf1DayIntervalEntry 4 }


pwCepPerf1DayIntervalDbaOutPacketsHC OBJECT-TYPE
	SYNTAX  Counter64
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Number of DBA packets sent."
	-- 1.3.6.1.2.1.200.1.7.1.5
	::= { pwCepPerf1DayIntervalEntry 5 }


-- Pointer adjustment stats

pwCepPerf1DayIntervalInNegPtrAdjust OBJECT-TYPE
	SYNTAX  Counter32
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Number of negative pointer adjustments sent on the
		SONET path based on CEP pointer adjustments received."
	-- 1.3.6.1.2.1.200.1.7.1.6
	::= { pwCepPerf1DayIntervalEntry 6 }


pwCepPerf1DayIntervalInPosPtrAdjust OBJECT-TYPE
	SYNTAX  Counter32
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Number of positive pointer adjustments sent on the
		SONET path based on CEP pointer adjustments received."
	-- 1.3.6.1.2.1.200.1.7.1.7
	::= { pwCepPerf1DayIntervalEntry 7 }


pwCepPerf1DayIntervalInPtrAdjustSecs OBJECT-TYPE
	SYNTAX  Counter32
	UNITS	"seconds"
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Number of seconds in which a positive or negative pointer
		adjustment was sent on the SONET path."
	-- 1.3.6.1.2.1.200.1.7.1.8
	::= { pwCepPerf1DayIntervalEntry 8 }


pwCepPerf1DayIntervalOutNegPtrAdjust OBJECT-TYPE
	SYNTAX  Counter32
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Number of negative pointer adjustments seen on the
		SONET path and encoded onto sent CEP packets."
	-- 1.3.6.1.2.1.200.1.7.1.9
	::= { pwCepPerf1DayIntervalEntry 9 }


pwCepPerf1DayIntervalOutPosPtrAdjust OBJECT-TYPE
	SYNTAX  Counter32
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Number of positive pointer adjustments seen on the
		SONET path and encoded onto sent CEP packets."
	-- 1.3.6.1.2.1.200.1.7.1.10
	::= { pwCepPerf1DayIntervalEntry 10 }


pwCepPerf1DayIntervalOutPtrAdjustSecs OBJECT-TYPE
	SYNTAX  Counter32
	UNITS	"seconds"
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Number of seconds in which a positive or negative pointer
		adjustment was seen on the SONET path."
	-- 1.3.6.1.2.1.200.1.7.1.11
	::= { pwCepPerf1DayIntervalEntry 11 }


pwCepPerf1DayIntervalAbsPtrAdjust OBJECT-TYPE
	SYNTAX  Integer32
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The relative adjustment of drift between inbound
		and outbound streams.  It is calculated as absolute
		value of:
		   (InPosPtrAdjust  -   InNegPtrAdjust) -
		   (OutPosPtrAdjust  -  OutNegPtrAdjust)"
	-- 1.3.6.1.2.1.200.1.7.1.12
	::= { pwCepPerf1DayIntervalEntry 12 }


pwCepPerf1DayIntervalMissingPkts OBJECT-TYPE
	SYNTAX  Counter32
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Number of missing packets (as detected via CEP header
		sequence number gaps)."
	-- 1.3.6.1.2.1.200.1.7.1.13
	::= { pwCepPerf1DayIntervalEntry 13 }


pwCepPerf1DayIntervalPktsOoseq OBJECT-TYPE
	SYNTAX  Counter32
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Number of packets detected out of sequence (via CEP
		header sequence numbers) but successfully reordered.
		Note: Some implementations may not support this feature
		(see pwCepCfgPktReorder)."
	-- 1.3.6.1.2.1.200.1.7.1.14
	::= { pwCepPerf1DayIntervalEntry 14 }


pwCepPerf1DayIntervalPktsOoRngDropped OBJECT-TYPE
	SYNTAX  Counter32
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Number of packets detected out of range (via CEP header
		sequence numbers) and could not be reordered or could not
		fit in the jitter buffer."
	-- 1.3.6.1.2.1.200.1.7.1.15
	::= { pwCepPerf1DayIntervalEntry 15 }


pwCepPerf1DayIntervalJtrBfrUnderruns OBJECT-TYPE
	SYNTAX  Counter32
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Number of times a packet needed to be played out, and the
		jitter buffer was empty."
	-- 1.3.6.1.2.1.200.1.7.1.16
	::= { pwCepPerf1DayIntervalEntry 16 }


pwCepPerf1DayIntervalPktsMalformed OBJECT-TYPE
	SYNTAX  Counter32
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Number of packets detected with unexpected size or bad
		headers stack."
	-- 1.3.6.1.2.1.200.1.7.1.17
	::= { pwCepPerf1DayIntervalEntry 17 }


pwCepPerf1DayIntervalSummaryErrors OBJECT-TYPE
	SYNTAX  Counter32
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"A summary of all the packet-error types above (from
		missing packets to bad length packets)."
	-- 1.3.6.1.2.1.200.1.7.1.18
	::= { pwCepPerf1DayIntervalEntry 18 }


pwCepPerf1DayIntervalESs OBJECT-TYPE
	SYNTAX  Counter32
	UNITS	"seconds"
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The counter associated with the number of Errored
		Seconds encountered."
	-- 1.3.6.1.2.1.200.1.7.1.19
	::= { pwCepPerf1DayIntervalEntry 19 }


pwCepPerf1DayIntervalSESs OBJECT-TYPE
	SYNTAX  Counter32
	UNITS	"seconds"
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The counter associated with the number of Severely
		Errored Seconds.  See pwCepCfgMissingPktsToSes."
	-- 1.3.6.1.2.1.200.1.7.1.20
	::= { pwCepPerf1DayIntervalEntry 20 }


pwCepPerf1DayIntervalUASs OBJECT-TYPE
	SYNTAX  Counter32
	UNITS	"seconds"
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The counter associated with the number of
		unavailable seconds.  See pwCepCfgSesToUAS.

		NOTE: When first entering the UAS state, the number
		of SesToUas is added to this object; then, as each
		additional UAS occurs, this object increments by one.

		NOTE: Similar to [RFC3592], if the agent chooses to update
		the various performance statistics in real time, it must
		be prepared to retroactively reduce the ES and SES counts
		(by the value of pwCepCfgSesToUas) and increase the UAS
		count (by that same value) when it determines that UAS
		state has been entered."
	-- 1.3.6.1.2.1.200.1.7.1.21
	::= { pwCepPerf1DayIntervalEntry 21 }


pwCepPerf1DayIntervalFC OBJECT-TYPE
	SYNTAX  Counter32
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"CEP Failure Counts (FC-CEP).  The number of CEP failure
		events.  A failure event begins when the LOPS failure
		is declared and ends when the failure is cleared."
	-- 1.3.6.1.2.1.200.1.7.1.22
	::= { pwCepPerf1DayIntervalEntry 22 }


-- End of CEP Performance 1-Day Table
-- Conformance information

pwCepGroups OBJECT IDENTIFIER 
	-- 1.3.6.1.2.1.200.2.1
	::= { pwCepConformance 1 }

pwCepCompliances OBJECT IDENTIFIER 
	-- 1.3.6.1.2.1.200.2.2
	::= { pwCepConformance 2 }


-- Compliance statement for full compliant implementations

pwCepModuleFullCompliance MODULE-COMPLIANCE
	STATUS  current
	DESCRIPTION
		"The compliance statement for agents that support
		full CEP PW configuration through this MIB module."

	MODULE 
	MANDATORY-GROUPS {
			pwCepGroup,
			pwCepCfgGroup,
			pwCepPerfCurrentGroup,
			pwCepPerfIntervalGroup,
			pwCepPerf1DayIntervalGroup }

	GROUP pwCepFractionalGroup
	  DESCRIPTION
		"This group is only mandatory for implementations
		that support fractional SPE."
	GROUP pwCepFractionalSts1Vc3Group
	  DESCRIPTION
		"This group is only mandatory for implementations
		that support the fractional STS-1/VC-3."
	GROUP pwCepFractionalVc4Group
	  DESCRIPTION
		"This group is only mandatory for implementations
		that support the fractional VC-4."
	GROUP pwCepSignalingGroup
	  DESCRIPTION
		"This group is only mandatory for implementations
		that support the CEP PW signaling."
	OBJECT pwCepType
	  SYNTAX INTEGER {
			spe(1) }
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"The support of the value vt(2) or fracSpe(3) is
		optional.  If either of these options are
		supported, read-write access is not required."
	OBJECT pwCepSonetPayloadLength
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required for implementations
		that support only the default values (which are
		based on the pwCepType)."
	OBJECT pwCepCfgMinPktLength
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required for implementations
		that support only a single predefined value."
	OBJECT pwCepCfgEnableDBA
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required for implementations
		that support only a single predefined value."
	OBJECT pwCepCfgRtpHdrSuppress
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required for implementations
		that do not support RTP header for CEP
		connections."
	OBJECT pwCepCfgConsecPktsInsync
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required for implementations
		that support only a single predefined value."
	OBJECT pwCepCfgConsecMissingOutSync
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required for implementations
		that support only a single predefined value."
	OBJECT pwCepCfgPktErrorPlayOutValue
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required for implementations
		that support only a single predefined value."
	OBJECT pwCepCfgMissingPktsToSes
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required for implementations
		that support only a single predefined value."
	OBJECT pwCepCfgSesToUas
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required for implementations
		that support only a single predefined value."
	OBJECT pwCepCfgSecsToExitUas
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required for implementations
		that support only a single predefined value."
	OBJECT pwCepCfgName
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT pwCepCfgRowStatus
	  SYNTAX RowStatus {
			active(1),
			notInService(2),
			notReady(3) }
	  WRITE-SYNTAX RowStatus {
			active(1),
			notInService(2),
			createAndGo(4),
			destroy(6) }
	  DESCRIPTION 
		"Support for createAndWait is not required."
	OBJECT pwCepFracMode
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required for implementations
		that support only a single predefined value."
	OBJECT pwCepFracAsync
	  SYNTAX PwCepFracAsyncMap {
			other(1) }
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Support for ds3(2) or e3(3) and read-write access
		is not required if the implementations do not
		support these options."
	OBJECT pwCepFracVtgMap
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required for implementations
		that support only a single predefined value."
	OBJECT pwCepFracEbm
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required for implementations
		where the EBM is derived from configuration in
		other MIB modules."
	OBJECT pwCepFracSdhVc4Mode
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required for implementations
		that support only a single predefined value."
	OBJECT pwCepFracSdhVc4Tu3Map1
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required for implementations
		that support only a single predefined value."
	OBJECT pwCepFracSdhVc4Tu3Map2
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required for implementations
		that support only a single predefined value."
	OBJECT pwCepFracSdhVc4Tu3Map3
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required for implementations
		that support only a single predefined value."
	OBJECT pwCepFracSdhVc4Tug2Map1
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required for implementations
		that support only a single predefined value."
	OBJECT pwCepFracSdhVc4Tug2Map2
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required for implementations
		that support only a single predefined value."
	OBJECT pwCepFracSdhVc4Tug2Map3
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required for implementations
		that support only a single predefined value."
	OBJECT pwCepFracSdhVc4Ebm1
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required for implementations
		where the EBM is derived from configuration in
		other MIB modules."
	OBJECT pwCepFracSdhVc4Ebm2
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required for implementations
		where the EBM is derived from configuration in
		other MIB modules."
	OBJECT pwCepFracSdhVc4Ebm3
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required for implementations
		where the EBM is derived from configuration in
		other MIB modules."
	OBJECT pwCepFracRowStatus
	  SYNTAX RowStatus {
			active(1),
			notInService(2),
			notReady(3) }
	  WRITE-SYNTAX RowStatus {
			active(1),
			notInService(2),
			createAndGo(4),
			destroy(6) }
	  DESCRIPTION 
		"Support for createAndWait is not required."
	-- 1.3.6.1.2.1.200.2.2.1
	::= { pwCepCompliances 1 }


-- Compliance requirement for read-only compliant implementations

pwCepModuleReadOnlyCompliance MODULE-COMPLIANCE
	STATUS  current
	DESCRIPTION
		"The compliance statement for agents that provide
		read-only support for the PW CEP MIB Module.  Such
		devices can be monitored but cannot be configured
		using this MIB module."

	MODULE 
	MANDATORY-GROUPS {
			pwCepGroup,
			pwCepCfgGroup,
			pwCepPerfCurrentGroup,
			pwCepPerfIntervalGroup,
			pwCepPerf1DayIntervalGroup }

	GROUP pwCepFractionalGroup
	  DESCRIPTION
		"This group is only mandatory for implementations
		that support fractional SPE."
	GROUP pwCepFractionalSts1Vc3Group
	  DESCRIPTION
		"This group is only mandatory for implementations
		that support the fractional STS-1/VC-3."
	GROUP pwCepFractionalVc4Group
	  DESCRIPTION
		"This group is only mandatory for implementations
		that support the fractional VC-4."
	GROUP pwCepSignalingGroup
	  DESCRIPTION
		"This group is only mandatory for implementations
		that support the CEP PW signaling."
	OBJECT pwCepType
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT pwCepSonetIfIndex
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT pwCepCfgIndex
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT pwCepSonetPayloadLength
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT pwCepCfgMinPktLength
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT pwCepCfgEnableDBA
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT pwCepCfgRtpHdrSuppress
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT pwCepCfgJtrBfrDepth
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT pwCepCfgConsecPktsInsync
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT pwCepCfgConsecMissingOutSync
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT pwCepCfgPktErrorPlayOutValue
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT pwCepCfgMissingPktsToSes
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT pwCepCfgSesToUas
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT pwCepCfgSecsToExitUas
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT pwCepCfgRowStatus
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT pwCepCfgStorageType
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT pwCepFracMode
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT pwCepFracAsync
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT pwCepFracVtgMap
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT pwCepFracEbm
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT pwCepFracSdhVc4Mode
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT pwCepFracSdhVc4Tu3Map1
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT pwCepFracSdhVc4Tu3Map2
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT pwCepFracSdhVc4Tu3Map3
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT pwCepFracSdhVc4Tug2Map1
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT pwCepFracSdhVc4Tug2Map2
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT pwCepFracSdhVc4Tug2Map3
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT pwCepFracSdhVc4Ebm1
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT pwCepFracSdhVc4Ebm2
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT pwCepFracSdhVc4Ebm3
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT pwCepFracRowStatus
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT pwCepFracStorageType
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	-- 1.3.6.1.2.1.200.2.2.2
	::= { pwCepCompliances 2 }

-- Units of conformance

pwCepGroup OBJECT-GROUP
	OBJECTS {
		pwCepType,
		pwCepSonetIfIndex,
		pwCepSonetConfigErrorOrStatus,
		pwCepCfgIndex,
		pwCepTimeElapsed,
		pwCepValidIntervals,
		pwCepIndications,
		pwCepLastEsTimeStamp }
	STATUS  current
	DESCRIPTION
		"Collection of objects for basic CEP PW config and
		status."
	-- 1.3.6.1.2.1.200.2.1.1
	::= { pwCepGroups 1 }

pwCepSignalingGroup OBJECT-GROUP
	OBJECTS {
		pwCepPeerCepOption }
	STATUS  current
	DESCRIPTION
		"Collection of objects required if the network element
		support CEP connections signaling."
	-- 1.3.6.1.2.1.200.2.1.2
	::= { pwCepGroups 2 }

pwCepCfgGroup OBJECT-GROUP
	OBJECTS {
		pwCepCfgIndexNext,
		pwCepSonetPayloadLength,
		pwCepCfgMinPktLength,
		pwCepCfgPktReorder,
		pwCepCfgEnableDBA,
		pwCepCfgRtpHdrSuppress,
		pwCepCfgJtrBfrDepth,
		pwCepCfgConsecPktsInsync,
		pwCepCfgConsecMissingOutSync,
		pwCepCfgPktErrorPlayOutValue,
		pwCepCfgMissingPktsToSes,
		pwCepCfgSesToUas,
		pwCepCfgSecsToExitUas,
		pwCepCfgName,
		pwCepCfgRowStatus,
		pwCepCfgStorageType }
	STATUS  current
	DESCRIPTION
		"Collection of detailed objects needed to
		configure CEP PWs."
	-- 1.3.6.1.2.1.200.2.1.3
	::= { pwCepGroups 3 }

pwCepPerfCurrentGroup OBJECT-GROUP
	OBJECTS {
		pwCepPerfCurrentDbaInPacketsHC,
		pwCepPerfCurrentDbaOutPacketsHC,
		pwCepPerfCurrentInNegPtrAdjust,
		pwCepPerfCurrentInPosPtrAdjust,
		pwCepPerfCurrentInPtrAdjustSecs,
		pwCepPerfCurrentOutNegPtrAdjust,
		pwCepPerfCurrentOutPosPtrAdjust,
		pwCepPerfCurrentOutPtrAdjustSecs,
		pwCepPerfCurrentAbsPtrAdjust,
		pwCepPerfCurrentMissingPkts,
		pwCepPerfCurrentPktsOoseq,
		pwCepPerfCurrentPktsOoRngDropped,
		pwCepPerfCurrentJtrBfrUnderruns,
		pwCepPerfCurrentPktsMalformed,
		pwCepPerfCurrentSummaryErrors,
		pwCepPerfCurrentESs,
		pwCepPerfCurrentSESs,
		pwCepPerfCurrentUASs,
		pwCepPerfCurrentFC }
	STATUS  current
	DESCRIPTION
		"Collection of statistics objects for CEP PWs."
	-- 1.3.6.1.2.1.200.2.1.4
	::= { pwCepGroups 4 }

pwCepPerfIntervalGroup OBJECT-GROUP
	OBJECTS {
		pwCepPerfIntervalValidData,
		pwCepPerfIntervalReset,
		pwCepPerfIntervalTimeElapsed,
		pwCepPerfIntervalDbaInPacketsHC,
		pwCepPerfIntervalDbaOutPacketsHC,
		pwCepPerfIntervalInNegPtrAdjust,
		pwCepPerfIntervalInPosPtrAdjust,
		pwCepPerfIntervalInPtrAdjustSecs,
		pwCepPerfIntervalOutNegPtrAdjust,
		pwCepPerfIntervalOutPosPtrAdjust,
		pwCepPerfIntervalOutPtrAdjustSecs,
		pwCepPerfIntervalAbsPtrAdjust,
		pwCepPerfIntervalMissingPkts,
		pwCepPerfIntervalPktsOoseq,
		pwCepPerfIntervalPktsOoRngDropped,
		pwCepPerfIntervalJtrBfrUnderruns,
		pwCepPerfIntervalPktsMalformed,
		pwCepPerfIntervalSummaryErrors,
		pwCepPerfIntervalESs,
		pwCepPerfIntervalSESs,
		pwCepPerfIntervalUASs,
		pwCepPerfIntervalFC }
	STATUS  current
	DESCRIPTION
		"Collection of statistics objects for CEP PWs."
	-- 1.3.6.1.2.1.200.2.1.5
	::= { pwCepGroups 5 }

pwCepPerf1DayIntervalGroup OBJECT-GROUP
	OBJECTS {
		pwCepPerf1DayIntervalValidData,
		pwCepPerf1DayIntervalMoniSecs,
		pwCepPerf1DayIntervalDbaInPacketsHC,
		pwCepPerf1DayIntervalDbaOutPacketsHC,
		pwCepPerf1DayIntervalInNegPtrAdjust,
		pwCepPerf1DayIntervalInPosPtrAdjust,
		pwCepPerf1DayIntervalInPtrAdjustSecs,
		pwCepPerf1DayIntervalOutNegPtrAdjust,
		pwCepPerf1DayIntervalOutPosPtrAdjust,
		pwCepPerf1DayIntervalOutPtrAdjustSecs,
		pwCepPerf1DayIntervalAbsPtrAdjust,
		pwCepPerf1DayIntervalMissingPkts,
		pwCepPerf1DayIntervalPktsOoseq,
		pwCepPerf1DayIntervalPktsOoRngDropped,
		pwCepPerf1DayIntervalJtrBfrUnderruns,
		pwCepPerf1DayIntervalPktsMalformed,
		pwCepPerf1DayIntervalSummaryErrors,
		pwCepPerf1DayIntervalESs,
		pwCepPerf1DayIntervalSESs,
		pwCepPerf1DayIntervalUASs,
		pwCepPerf1DayIntervalFC }
	STATUS  current
	DESCRIPTION
		"Collection of statistics objects for CEP PWs."
	-- 1.3.6.1.2.1.200.2.1.6
	::= { pwCepGroups 6 }

pwCepFractionalGroup OBJECT-GROUP
	OBJECTS {
		pwCepFracRowStatus,
		pwCepFracStorageType }
	STATUS  current
	DESCRIPTION
		"Collection of fractional SPE objects.  These objects
		are optional and should be supported only if
		fractional SPE is supported within the network
		element."
	-- 1.3.6.1.2.1.200.2.1.7
	::= { pwCepGroups 7 }

pwCepFractionalSts1Vc3Group OBJECT-GROUP
	OBJECTS {
		pwCepFracMode,
		pwCepFracConfigError,
		pwCepFracAsync,
		pwCepFracVtgMap,
		pwCepFracEbm,
		pwCepFracPeerEbm }
	STATUS  current
	DESCRIPTION
		"Collection of fractional STS-1/VC3 objects.  These
		objects are optional and should be supported only if
		fractional STS-1/VC3 is supported within the network
		element."
	-- 1.3.6.1.2.1.200.2.1.8
	::= { pwCepGroups 8 }

pwCepFractionalVc4Group OBJECT-GROUP
	OBJECTS {
		pwCepFracSdhVc4Mode,
		pwCepFracSdhVc4Tu3Map1,
		pwCepFracSdhVc4Tu3Map2,
		pwCepFracSdhVc4Tu3Map3,
		pwCepFracSdhVc4Tug2Map1,
		pwCepFracSdhVc4Tug2Map2,
		pwCepFracSdhVc4Tug2Map3,
		pwCepFracSdhVc4Ebm1,
		pwCepFracSdhVc4Ebm2,
		pwCepFracSdhVc4Ebm3,
		pwCepFracSdhVc4PeerEbm1,
		pwCepFracSdhVc4PeerEbm2,
		pwCepFracSdhVc4PeerEbm3 }
	STATUS  current
	DESCRIPTION
		"Collection of fractional VC4 objects.  These objects
		are optional and should be supported only if
		fractional VC4 is supported within the network
		element."
	-- 1.3.6.1.2.1.200.2.1.9
	::= { pwCepGroups 9 }

END
