OSPFV3-MIB DEFINITIONS ::= BEGIN

IMPORTS
	MODULE-IDENTITY,
	OBJECT-TYPE,
	NOTIFICATION-TYPE,
	mib-2,
	Counter32,
	Gauge32,
	Integer32,
	Unsigned32
		FROM SNMPv2-SMI
	TEXTUAL-CONVENTION,
	TruthValue,
	RowStatus,
	TimeStamp
		FROM SNMPv2-TC
	MODULE-COMPLIANCE,
	OBJECT-GROUP,
	NOTIFICATION-GROUP
		FROM SNMPv2-CONF
	InterfaceIndex
		FROM IF-MIB
	InetAddressType,
	InetAddress,
	InetAddressPrefixLength,
	InetAddressIPv6
		FROM INET-ADDRESS-MIB
	Metric,
	BigMetric,
	Status,
	HelloRange,
	DesignatedRouterPriority
		FROM OSPF-MIB;

ospfv3MIB MODULE-IDENTITY
	LAST-UPDATED "200908130000Z"	-- Aug 13, 2009 12:00:00 AM
	ORGANIZATION "IETF OSPF Working Group"
	CONTACT-INFO
		"WG E-Mail: ospf@ietf.org
		WG Chairs: Acee Lindem
		           acee@redback.com

		           Abhay Roy
		           akr@cisco.com

		Editors:   Dan Joyal
		           Nortel
		           600 Technology Park Drive
		           Billerica, MA  01821, USA
		           djoyal@nortel.com

		           Vishwas Manral
		           IP Infusion
		           Almora, Uttarakhand
		           India
		           vishwas@ipinfusion.com"
	DESCRIPTION
		"The MIB module for OSPF version 3.

		 Copyright (c) 2009 IETF Trust and the persons
		 identified as authors of the code.  All rights
		 reserved.

		 Redistribution and use in source and binary forms, with
		 or without modification, are permitted provided that
		 the following conditions are met:

		 - Redistributions of source code must retain the above
		   copyright notice, this list of conditions and the
		   following disclaimer.

		- Redistributions in binary form must reproduce the
		  above copyright notice, this list of conditions and
		  the following disclaimer in the documentation and/or
		  other materials provided with the distribution.

		- Neither the name of Internet Society, IETF or IETF
		  Trust, nor the names of specific contributors, may be
		  used to endorse or promote products derived from this
		  software without specific prior written permission.

		  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND
		  CONTRIBUTORS 'AS IS' AND ANY EXPRESS OR IMPLIED
		  WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
		  WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
		  PARTICULAR PURPOSE ARE DISCLAIMED.  IN NO EVENT SHALL
		  THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY
		  DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
		  CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
		  PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
		  USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
		  HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
		  IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
		  NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE
		  USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
		  POSSIBILITY OF SUCH DAMAGE.

		  This version of this MIB module is part of RFC 5643;
		  see the RFC itself for full legal notices."
	REVISION "200908130000Z"	-- Aug 13, 2009 12:00:00 AM
	DESCRIPTION
		"Initial version, published as RFC 5643"
	-- 1.3.6.1.2.1.191
	::= { mib-2 191 }


-- Textual conventions

Ospfv3UpToRefreshIntervalTC ::= TEXTUAL-CONVENTION
	DISPLAY-HINT "d"
	STATUS  current
	DESCRIPTION
		"The values one might be able to configure for
		variables bounded by the Refresh Interval."
	REFERENCE
		"OSPF Version 2, Appendix B, Architectural Constants"
	SYNTAX Unsigned32 (1..1800)


Ospfv3DeadIntervalRangeTC ::= TEXTUAL-CONVENTION
	DISPLAY-HINT "d"
	STATUS  current
	DESCRIPTION
		"The range, in seconds, of dead interval value."
	REFERENCE
		"OSPF for IPv6, Appendix C.3, Router Interface
		Parameters"
	SYNTAX Unsigned32 (1..65535)


Ospfv3RouterIdTC ::= TEXTUAL-CONVENTION
	DISPLAY-HINT "d"
	STATUS  current
	DESCRIPTION
		"A 32-bit, unsigned integer uniquely identifying the
		router in the Autonomous System.  To ensure
		uniqueness, this may default to the value of one of
		the router's IPv4 host addresses if IPv4 is
		configured on the router."
	REFERENCE
		"OSPF for IPv6, Appendix C.1, Global Parameters"
	SYNTAX Unsigned32 (1..4294967295)


Ospfv3LsIdTC ::= TEXTUAL-CONVENTION
	DISPLAY-HINT "d"
	STATUS  current
	DESCRIPTION
		"A unique 32-bit identifier of the piece of the
		routing domain that is being described by a link
		state advertisement.  In contrast to OSPFv2, the
		Link State ID (LSID) has no addressing semantics."
	REFERENCE
		"OSPF Version 2, Section 12.1.4, Link State ID"
	SYNTAX Unsigned32 (1..4294967295)


Ospfv3AreaIdTC ::= TEXTUAL-CONVENTION
	DISPLAY-HINT "d"
	STATUS  current
	DESCRIPTION
		"An OSPFv3 Area Identifier.  A value of zero
		identifies the backbone area."
	REFERENCE
		"OSPF for IPv6, Appendix C.3 Router Interface
		Parameters"
	SYNTAX Unsigned32 (0..4294967295)


Ospfv3IfInstIdTC ::= TEXTUAL-CONVENTION
	DISPLAY-HINT "d"
	STATUS  current
	DESCRIPTION
		"An OSPFv3 Interface Instance ID."
	REFERENCE
		"OSPF for IPv6, Appendix C.3, Router Interface
		Parameters"
	SYNTAX Unsigned32 (0..255)


Ospfv3LsaSequenceTC ::= TEXTUAL-CONVENTION
	DISPLAY-HINT "d"
	STATUS  current
	DESCRIPTION
		"The sequence number field is a signed 32-bit
		integer.  It is used to detect old and duplicate
		link state advertisements.  The space of
		sequence numbers is linearly ordered.  The
		larger the sequence number, the more recent the
		advertisement."
	REFERENCE
		"OSPF Version 2, Section 12.1.6, LS sequence
		number"
	SYNTAX Integer32


Ospfv3LsaAgeTC ::= TEXTUAL-CONVENTION
	DISPLAY-HINT "d"
	STATUS  current
	DESCRIPTION
		"The age of the link state advertisement in
		seconds.  The high-order bit of the LS age
		field is considered the DoNotAge bit for
		support of on-demand circuits."
	REFERENCE
		"OSPF Version 2, Section 12.1.1, LS age;
		Extending OSPF to Support Demand Circuits,
		Section 2.2, The LS age field"
	SYNTAX Unsigned32 (0..3600 | 32768..36368)


-- Top-level structure of MIB

ospfv3Notifications OBJECT IDENTIFIER 
	-- 1.3.6.1.2.1.191.0
	::= { ospfv3MIB 0 }

ospfv3Objects OBJECT IDENTIFIER 
	-- 1.3.6.1.2.1.191.1
	::= { ospfv3MIB 1 }

ospfv3Conformance OBJECT IDENTIFIER 
	-- 1.3.6.1.2.1.191.2
	::= { ospfv3MIB 2 }

-- OSPFv3 General Variables
-- These parameters apply globally to the Router's
-- OSPFv3 Process.

ospfv3GeneralGroup OBJECT IDENTIFIER 
	-- 1.3.6.1.2.1.191.1.1
	::= { ospfv3Objects 1 }

ospfv3RouterId OBJECT-TYPE
	SYNTAX  Ospfv3RouterIdTC
	MAX-ACCESS read-write
	STATUS  current
	DESCRIPTION
		"A 32-bit unsigned integer uniquely identifying
		the router in the Autonomous System.  To ensure
		uniqueness, this may default to the 32-bit
		unsigned integer representation of one of
		the router's IPv4 interface addresses (if IPv4
		is configured on the router).

		This object is persistent, and when written, the
		entity SHOULD save the change to non-volatile
		storage."
	REFERENCE
		"OSPF for IPv6, Appendix C.1, Global Parameters"
	-- 1.3.6.1.2.1.191.1.1.1
	::= { ospfv3GeneralGroup 1 }


ospfv3AdminStatus OBJECT-TYPE
	SYNTAX  Status
	MAX-ACCESS read-write
	STATUS  current
	DESCRIPTION
		"The administrative status of OSPFv3 in the
		router.  The value 'enabled' denotes that the
		OSPFv3 Process is active on at least one
		interface; 'disabled' disables it on all
		interfaces.

		This object is persistent, and when written, the
		entity SHOULD save the change to non-volatile
		storage."
	-- 1.3.6.1.2.1.191.1.1.2
	::= { ospfv3GeneralGroup 2 }


ospfv3VersionNumber OBJECT-TYPE
	SYNTAX  INTEGER {
			version3(3) }
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The version number of OSPF for IPv6 is 3."
	-- 1.3.6.1.2.1.191.1.1.3
	::= { ospfv3GeneralGroup 3 }


ospfv3AreaBdrRtrStatus OBJECT-TYPE
	SYNTAX  TruthValue
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"A flag to denote whether this router is an area
		border router.  The value of this object is true (1)
		when the router is an area border router."
	REFERENCE
		"OSPF Version 2, Section 3, Splitting the AS into
		Areas"
	-- 1.3.6.1.2.1.191.1.1.4
	::= { ospfv3GeneralGroup 4 }


ospfv3ASBdrRtrStatus OBJECT-TYPE
	SYNTAX  TruthValue
	MAX-ACCESS read-write
	STATUS  current
	DESCRIPTION
		"A flag to note whether this router is
		configured as an Autonomous System border router.

		This object is persistent, and when written, the
		entity SHOULD save the change to non-volatile
		storage."
	REFERENCE
		"OSPF Version 2, Section 3.3, Classification of
		routers"
	-- 1.3.6.1.2.1.191.1.1.5
	::= { ospfv3GeneralGroup 5 }


ospfv3AsScopeLsaCount OBJECT-TYPE
	SYNTAX  Gauge32
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The number of AS-scope (e.g., AS-External) link state
		advertisements in the link state database."
	-- 1.3.6.1.2.1.191.1.1.6
	::= { ospfv3GeneralGroup 6 }


ospfv3AsScopeLsaCksumSum OBJECT-TYPE
	SYNTAX  Unsigned32
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The 32-bit unsigned sum of the LS checksums of
		the AS-scoped link state advertisements
		contained in the link state database.  This sum
		can be used to determine if there has been a
		change in a router's link state database or
		to compare the link state database of two
		routers."
	-- 1.3.6.1.2.1.191.1.1.7
	::= { ospfv3GeneralGroup 7 }


ospfv3OriginateNewLsas OBJECT-TYPE
	SYNTAX  Counter32
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The number of new link state advertisements
		that have been originated.  This number is
		incremented each time the router originates a new
		LSA.

		Discontinuities in the value of this counter
		can occur at re-initialization of the management
		system and at other times as indicated by the
		value of ospfv3DiscontinuityTime."
	-- 1.3.6.1.2.1.191.1.1.8
	::= { ospfv3GeneralGroup 8 }


ospfv3RxNewLsas OBJECT-TYPE
	SYNTAX  Counter32
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The number of link state advertisements
		received that are determined to be new
		instantiations.  This number does not include
		newer instantiations of self-originated link state
		advertisements.

		Discontinuities in the value of this counter
		can occur at re-initialization of the management
		system and at other times as indicated by the
		value of ospfv3DiscontinuityTime."
	-- 1.3.6.1.2.1.191.1.1.9
	::= { ospfv3GeneralGroup 9 }


ospfv3ExtLsaCount OBJECT-TYPE
	SYNTAX  Gauge32
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The number of External (LS type 0x4005) in the
		link state database."
	-- 1.3.6.1.2.1.191.1.1.10
	::= { ospfv3GeneralGroup 10 }


ospfv3ExtAreaLsdbLimit OBJECT-TYPE
	SYNTAX  Integer32 (-1..2147483647)
	MAX-ACCESS read-write
	STATUS  current
	DESCRIPTION
		"The maximum number of non-default
		AS-external-LSA entries that can be stored in the
		link state database.  If the value is -1, then
		there is no limit.

		When the number of non-default AS-external-LSAs
		in a router's link state database reaches
		ospfv3ExtAreaLsdbLimit, the router enters Overflow
		state.  The router never holds more than
		ospfv3ExtAreaLsdbLimit non-default AS-external-LSAs
		in its database.  ospfv3ExtAreaLsdbLimit MUST be set
		identically in all routers attached to the OSPFv3
		backbone and/or any regular OSPFv3 area (i.e.,
		OSPFv3 stub areas and not-so-stubby-areas (NSSAs)
		are excluded).

		This object is persistent, and when written, the
		entity SHOULD save the change to non-volatile
		storage."
	-- 1.3.6.1.2.1.191.1.1.11
	::= { ospfv3GeneralGroup 11 }


ospfv3ExitOverflowInterval OBJECT-TYPE
	SYNTAX  Unsigned32
	UNITS	"seconds"
	MAX-ACCESS read-write
	STATUS  current
	DESCRIPTION
		"The number of seconds that, after entering
		Overflow state, a router will attempt to leave
		Overflow state.  This allows the router to again
		originate non-default, AS-External-LSAs.  When
		set to 0, the router will not leave Overflow
		state until restarted.

		This object is persistent, and when written, the
		entity SHOULD save the change to non-volatile
		storage."
	-- 1.3.6.1.2.1.191.1.1.12
	::= { ospfv3GeneralGroup 12 }


ospfv3DemandExtensions OBJECT-TYPE
	SYNTAX  TruthValue
	MAX-ACCESS read-write
	STATUS  current
	DESCRIPTION
		"The router's support for demand circuits.
		The value of this object is true (1) when
		demand circuits are supported.

		This object is persistent, and when written, the
		entity SHOULD save the change to non-volatile
		storage."
	REFERENCE
		"OSPF Version 2; Extending OSPF to Support Demand
		Circuits"
	-- 1.3.6.1.2.1.191.1.1.13
	::= { ospfv3GeneralGroup 13 }


ospfv3ReferenceBandwidth OBJECT-TYPE
	SYNTAX  Unsigned32
	UNITS	"kilobits per second"
	MAX-ACCESS read-write
	STATUS  current
	DESCRIPTION
		"Reference bandwidth in kilobits per second for
		calculating default interface metrics.  The
		default value is 100,000 KBPS (100 MBPS).

		This object is persistent, and when written, the
		entity SHOULD save the change to non-volatile
		storage."
	REFERENCE
		"OSPF Version 2, Appendix C.3, Router interface
		parameters"
	DEFVAL { 100000 }
	-- 1.3.6.1.2.1.191.1.1.14
	::= { ospfv3GeneralGroup 14 }


ospfv3RestartSupport OBJECT-TYPE
	SYNTAX  INTEGER {
			none(1),
			plannedOnly(2),
			plannedAndUnplanned(3) }
	MAX-ACCESS read-write
	STATUS  current
	DESCRIPTION
		"The router's support for OSPF graceful restart.
		Options include no restart support, only planned





		restarts, or both planned and unplanned restarts.

		This object is persistent, and when written, the
		entity SHOULD save the change to non-volatile
		storage."
	REFERENCE
		"Graceful OSPF Restart, Appendix B.1, Global
		Parameters (Minimum subset)"
	-- 1.3.6.1.2.1.191.1.1.15
	::= { ospfv3GeneralGroup 15 }


ospfv3RestartInterval OBJECT-TYPE
	SYNTAX  Ospfv3UpToRefreshIntervalTC
	UNITS	"seconds"
	MAX-ACCESS read-write
	STATUS  current
	DESCRIPTION
		"Configured OSPF graceful restart timeout interval.

		This object is persistent, and when written, the
		entity SHOULD save the change to non-volatile
		storage."
	REFERENCE
		"Graceful OSPF Restart, Appendix B.1, Global
		Parameters (Minimum subset)"
	DEFVAL { 120 }
	-- 1.3.6.1.2.1.191.1.1.16
	::= { ospfv3GeneralGroup 16 }


ospfv3RestartStrictLsaChecking OBJECT-TYPE
	SYNTAX  TruthValue
	MAX-ACCESS read-write
	STATUS  current
	DESCRIPTION
		"Indicates if strict LSA checking is enabled for
		graceful restart.  A value of true (1) indicates that
		strict LSA checking is enabled.

		This object is persistent, and when written,
		the entity SHOULD save the change to non-volatile
		storage."
	REFERENCE
		"Graceful OSPF Restart, Appendix B.2, Global
		Parameters (Optional)"
	DEFVAL { true }
	-- 1.3.6.1.2.1.191.1.1.17
	::= { ospfv3GeneralGroup 17 }


ospfv3RestartStatus OBJECT-TYPE
	SYNTAX  INTEGER {
			notRestarting(1),
			plannedRestart(2),
			unplannedRestart(3) }
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The current status of OSPF graceful restart capability."
	-- 1.3.6.1.2.1.191.1.1.18
	::= { ospfv3GeneralGroup 18 }


ospfv3RestartAge OBJECT-TYPE
	SYNTAX  Ospfv3UpToRefreshIntervalTC
	UNITS	"seconds"
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Remaining time in the current OSPF graceful restart
		interval."
	-- 1.3.6.1.2.1.191.1.1.19
	::= { ospfv3GeneralGroup 19 }


ospfv3RestartExitReason OBJECT-TYPE
	SYNTAX  INTEGER {
			none(1),
			inProgress(2),
			completed(3),
			timedOut(4),
			topologyChanged(5) }
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Describes the outcome of the last attempt at a
		graceful restart.

		none:            no restart has yet been attempted.
		inProgress:      a restart attempt is currently underway.
		completed:       the last restart completed successfully.
		timedOut:        the last restart timed out.
		topologyChanged: the last restart was aborted due to
		                 a topology change."
	-- 1.3.6.1.2.1.191.1.1.20
	::= { ospfv3GeneralGroup 20 }


ospfv3NotificationEnable OBJECT-TYPE
	SYNTAX  TruthValue
	MAX-ACCESS read-write
	STATUS  current
	DESCRIPTION
		"This object provides a coarse level of control
		over the generation of OSPFv3 notifications.

		If this object is set to true (1), then it enables
		the generation of OSPFv3 notifications.  If it is
		set to false (2), these notifications are not
		generated.





		This object is persistent, and when written, the
		entity SHOULD save the change to non-volatile
		storage."
	-- 1.3.6.1.2.1.191.1.1.21
	::= { ospfv3GeneralGroup 21 }


ospfv3StubRouterSupport OBJECT-TYPE
	SYNTAX  TruthValue
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The router's support for stub router functionality.  An
		object value of true (1) indicates that stub router
		functionality is supported."
	REFERENCE
		"OSPF Stub Router Advertisement"
	-- 1.3.6.1.2.1.191.1.1.22
	::= { ospfv3GeneralGroup 22 }


ospfv3StubRouterAdvertisement OBJECT-TYPE
	SYNTAX  INTEGER {
			doNotAdvertise(1),
			advertise(2) }
	MAX-ACCESS read-write
	STATUS  current
	DESCRIPTION
		"This object controls the advertisement of
		stub LSAs by the router.  The value
		doNotAdvertise (1) will result in the advertisement
		of standard LSAs and is the default value.

		This object is persistent, and when written,
		the entity SHOULD save the change to non-volatile
		storage."
	REFERENCE
		"OSPF Stub Router Advertisement, Section 2, Proposed
		Solution"
	DEFVAL { doNotAdvertise }
	-- 1.3.6.1.2.1.191.1.1.23
	::= { ospfv3GeneralGroup 23 }


ospfv3DiscontinuityTime OBJECT-TYPE
	SYNTAX  TimeStamp
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The value of sysUpTime on the most recent occasion
		at which any one of this MIB's counters suffered
		a discontinuity.






		If no such discontinuities have occurred since the last
		re-initialization of the local management subsystem,
		then this object contains a zero value."
	-- 1.3.6.1.2.1.191.1.1.24
	::= { ospfv3GeneralGroup 24 }


ospfv3RestartTime OBJECT-TYPE
	SYNTAX  TimeStamp
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The value of sysUpTime on the most recent occasion
		at which the ospfv3RestartExitReason was updated."
	-- 1.3.6.1.2.1.191.1.1.25
	::= { ospfv3GeneralGroup 25 }


-- The OSPFv3 Area Data Structure contains information
-- regarding the various areas.  The interfaces and
-- virtual links are configured as part of these areas.
-- Area 0, by definition, is the backbone area.

ospfv3AreaTable OBJECT-TYPE
	SYNTAX  SEQUENCE OF Ospfv3AreaEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"Information describing the configured
		parameters and cumulative statistics of the router's
		attached areas.  The interfaces and
		virtual links are configured as part of these areas.
		Area 0, by definition, is the backbone area."
	REFERENCE
		"OSPF Version 2, Section 6, The Area Data
		Structure"
	-- 1.3.6.1.2.1.191.1.2
	::= { ospfv3Objects 2 }


ospfv3AreaEntry OBJECT-TYPE
	SYNTAX  Ospfv3AreaEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"Information describing the configured
		parameters and cumulative statistics of one of the
		router's attached areas.

		The information in this table is persistent,
		and when written, the entity SHOULD save the a
		change to non-volatile storage."
	INDEX {
		ospfv3AreaId }
	-- 1.3.6.1.2.1.191.1.2.1
	::= { ospfv3AreaTable 1 }


Ospfv3AreaEntry ::= SEQUENCE {

	ospfv3AreaId                         Ospfv3AreaIdTC,
	ospfv3AreaImportAsExtern             INTEGER,
	ospfv3AreaSpfRuns                    Counter32,
	ospfv3AreaBdrRtrCount                Gauge32,
	ospfv3AreaAsBdrRtrCount              Gauge32,
	ospfv3AreaScopeLsaCount              Gauge32,
	ospfv3AreaScopeLsaCksumSum           Unsigned32,
	ospfv3AreaSummary                    INTEGER,
	ospfv3AreaRowStatus                  RowStatus,
	ospfv3AreaStubMetric                 BigMetric,
	ospfv3AreaNssaTranslatorRole         INTEGER,
	ospfv3AreaNssaTranslatorState        INTEGER,
	ospfv3AreaNssaTranslatorStabInterval Unsigned32,
	ospfv3AreaNssaTranslatorEvents       Counter32,
	ospfv3AreaStubMetricType             INTEGER,
	ospfv3AreaTEEnabled                  TruthValue }


ospfv3AreaId OBJECT-TYPE
	SYNTAX  Ospfv3AreaIdTC
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"A 32-bit unsigned integer uniquely identifying an area.
		Area ID 0 is used for the OSPFv3 backbone."
	REFERENCE
		"OSPF Version 2, Appendix C.2, Area parameters"
	-- 1.3.6.1.2.1.191.1.2.1.1
	::= { ospfv3AreaEntry 1 }


ospfv3AreaImportAsExtern OBJECT-TYPE
	SYNTAX  INTEGER {
			importExternal(1),   	-- normal area
			importNoExternal(2), 	-- stub area
			importNssa(3)       	-- not-so-stubby-area
			}
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"Indicates whether an area is a stub area, NSSA, or
		standard area.  AS-scope LSAs are not imported into stub
		areas or NSSAs.  NSSAs import AS-External data as NSSA
		LSAs that have Area-scope."
	REFERENCE
		"OSPF Version 2, Appendix C.2, Area parameters"
	DEFVAL { importExternal }
	-- 1.3.6.1.2.1.191.1.2.1.2
	::= { ospfv3AreaEntry 2 }


ospfv3AreaSpfRuns OBJECT-TYPE
	SYNTAX  Counter32
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The number of times that the intra-area route
		table has been calculated using this area's
		link state database.  This is typically done
		using Dijkstra's algorithm.

		Discontinuities in the value of this counter
		can occur at re-initialization of the management
		system and at other times as indicated by the
		value of ospfv3DiscontinuityTime."
	-- 1.3.6.1.2.1.191.1.2.1.3
	::= { ospfv3AreaEntry 3 }


ospfv3AreaBdrRtrCount OBJECT-TYPE
	SYNTAX  Gauge32
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The total number of area border routers
		reachable within this area.  This is initially zero,
		and is calculated in each Shortest Path First (SPF)
		pass."
	DEFVAL { 0 }
	-- 1.3.6.1.2.1.191.1.2.1.4
	::= { ospfv3AreaEntry 4 }


ospfv3AreaAsBdrRtrCount OBJECT-TYPE
	SYNTAX  Gauge32
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The total number of Autonomous System border
		routers reachable within this area.  This is
		initially zero, and is calculated in each SPF
		pass."
	DEFVAL { 0 }
	-- 1.3.6.1.2.1.191.1.2.1.5
	::= { ospfv3AreaEntry 5 }


ospfv3AreaScopeLsaCount OBJECT-TYPE
	SYNTAX  Gauge32
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The total number of Area-scope link state
		advertisements in this area's link state
		database."
	DEFVAL { 0 }
	-- 1.3.6.1.2.1.191.1.2.1.6
	::= { ospfv3AreaEntry 6 }


ospfv3AreaScopeLsaCksumSum OBJECT-TYPE
	SYNTAX  Unsigned32
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The 32-bit unsigned sum of the Area-scope link state
		advertisements' LS checksums contained in this
		area's link state database.  The sum can be used
		to determine if there has been a change in a
		router's link state database or to compare the
		link state database of two routers."
	-- 1.3.6.1.2.1.191.1.2.1.7
	::= { ospfv3AreaEntry 7 }


ospfv3AreaSummary OBJECT-TYPE
	SYNTAX  INTEGER {
			noAreaSummary(1),
			sendAreaSummary(2) }
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"The variable ospfv3AreaSummary controls the
		import of Inter-Area LSAs into stub and
		NSSA areas.  It has no effect on other areas.






		If it is noAreaSummary, the router will neither
		originate nor propagate Inter-Area LSAs into the
		stub or NSSA area.  It will only advertise a
		default route.

		If it is sendAreaSummary, the router will both
		summarize and propagate Inter-Area LSAs."
	DEFVAL { sendAreaSummary }
	-- 1.3.6.1.2.1.191.1.2.1.8
	::= { ospfv3AreaEntry 8 }


ospfv3AreaRowStatus OBJECT-TYPE
	SYNTAX  RowStatus
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"This object permits management of the table by
		facilitating actions such as row creation,
		construction, and destruction.

		The value of this object has no effect on
		whether other objects in this conceptual row can be
		modified."
	-- 1.3.6.1.2.1.191.1.2.1.9
	::= { ospfv3AreaEntry 9 }


ospfv3AreaStubMetric OBJECT-TYPE
	SYNTAX  BigMetric
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"The metric value advertised for the default route
		into stub and NSSA areas.  By default, this equals the
		least metric among the interfaces to other areas."
	-- 1.3.6.1.2.1.191.1.2.1.10
	::= { ospfv3AreaEntry 10 }


ospfv3AreaNssaTranslatorRole OBJECT-TYPE
	SYNTAX  INTEGER {
			always(1),
			candidate(2) }
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"Indicates an NSSA border router's policy to
		perform NSSA translation of NSSA-LSAs into
		AS-External-LSAs."
	DEFVAL { candidate }
	-- 1.3.6.1.2.1.191.1.2.1.11
	::= { ospfv3AreaEntry 11 }


ospfv3AreaNssaTranslatorState OBJECT-TYPE
	SYNTAX  INTEGER {
			enabled(1),
			elected(2),
			disabled(3) }
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Indicates if and how an NSSA border router is
		performing NSSA translation of NSSA-LSAs into
		AS-External-LSAs.  When this object is set to
		'enabled', the NSSA border router's
		ospfv3AreaNssaTranslatorRole has been set to 'always'.
		When this object is set to 'elected', a candidate
		NSSA border router is translating NSSA-LSAs into
		AS-External-LSAs.  When this object is set to
		'disabled', a candidate NSSA Border router is NOT
		translating NSSA-LSAs into AS-External-LSAs."
	-- 1.3.6.1.2.1.191.1.2.1.12
	::= { ospfv3AreaEntry 12 }


ospfv3AreaNssaTranslatorStabInterval OBJECT-TYPE
	SYNTAX  Unsigned32
	UNITS	"seconds"
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"The stability interval defined as the number of
		seconds after an elected translator determines its
		services are no longer required that it should
		continue to perform its translation duties."
	DEFVAL { 40 }
	-- 1.3.6.1.2.1.191.1.2.1.13
	::= { ospfv3AreaEntry 13 }


ospfv3AreaNssaTranslatorEvents OBJECT-TYPE
	SYNTAX  Counter32
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Indicates the number of Translator state changes
		that have occurred since the last start-up of the
		OSPFv3 routing process.

		Discontinuities in the value of this counter
		can occur at re-initialization of the management
		system and at other times as indicated by the
		value of ospfv3DiscontinuityTime."
	-- 1.3.6.1.2.1.191.1.2.1.14
	::= { ospfv3AreaEntry 14 }


ospfv3AreaStubMetricType OBJECT-TYPE
	SYNTAX  INTEGER {
			ospfv3Metric(1),   	-- OSPF Metric
			comparableCost(2), 	-- external type 1
			nonComparable(3)  	-- external type 2
			}
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"This variable assigns the type of metric
		advertised as a default route."
	DEFVAL { ospfv3Metric }
	-- 1.3.6.1.2.1.191.1.2.1.15
	::= { ospfv3AreaEntry 15 }


ospfv3AreaTEEnabled OBJECT-TYPE
	SYNTAX  TruthValue
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"Indicates whether or not traffic engineering
		is enabled in the area.  The object is set
		to the value true (1) to enable traffic engineering.
		Traffic engineering is disabled by default."
	DEFVAL { false }
	-- 1.3.6.1.2.1.191.1.2.1.16
	::= { ospfv3AreaEntry 16 }


-- OSPFv3 AS-Scope Link State Database

ospfv3AsLsdbTable OBJECT-TYPE
	SYNTAX  SEQUENCE OF Ospfv3AsLsdbEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"The OSPFv3 Process's AS-scope link state database
		(LSDB).  The LSDB contains the AS-scope link state
		advertisements from throughout the areas that the
		device is attached to."
	-- 1.3.6.1.2.1.191.1.3
	::= { ospfv3Objects 3 }


ospfv3AsLsdbEntry OBJECT-TYPE
	SYNTAX  Ospfv3AsLsdbEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"A single AS-scope link state advertisement."
	INDEX {
		ospfv3AsLsdbType,
		ospfv3AsLsdbRouterId,
		ospfv3AsLsdbLsid }
	-- 1.3.6.1.2.1.191.1.3.1
	::= { ospfv3AsLsdbTable 1 }


Ospfv3AsLsdbEntry ::= SEQUENCE {

	ospfv3AsLsdbType          Unsigned32,
	ospfv3AsLsdbRouterId      Ospfv3RouterIdTC,
	ospfv3AsLsdbLsid          Ospfv3LsIdTC,
	ospfv3AsLsdbSequence      Ospfv3LsaSequenceTC,
	ospfv3AsLsdbAge           Ospfv3LsaAgeTC,
	ospfv3AsLsdbChecksum      Integer32,
	ospfv3AsLsdbAdvertisement OCTET STRING,
	ospfv3AsLsdbTypeKnown     TruthValue }


ospfv3AsLsdbType OBJECT-TYPE
	SYNTAX  Unsigned32 (0..4294967295)
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"The type of the link state advertisement.
		Each link state type has a separate
		advertisement format.  AS-scope LSAs not recognized
		by the router may be stored in the database."
	-- 1.3.6.1.2.1.191.1.3.1.1
	::= { ospfv3AsLsdbEntry 1 }


ospfv3AsLsdbRouterId OBJECT-TYPE
	SYNTAX  Ospfv3RouterIdTC
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"The 32-bit number that uniquely identifies the
		originating router in the Autonomous System."
	REFERENCE
		"OSPF Version 2, Appendix C.1, Global parameters"
	-- 1.3.6.1.2.1.191.1.3.1.2
	::= { ospfv3AsLsdbEntry 2 }


ospfv3AsLsdbLsid OBJECT-TYPE
	SYNTAX  Ospfv3LsIdTC
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"The Link State ID is an LS type-specific field
		containing a unique identifier;
		it identifies the piece of the routing domain
		that is being described by the advertisement.
		In contrast to OSPFv2, the LSID has no
		addressing semantics."
	-- 1.3.6.1.2.1.191.1.3.1.3
	::= { ospfv3AsLsdbEntry 3 }


-- Note that the OSPF sequence number is a 32-bit signed
-- integer.  It starts with the value '80000001'h
-- or -'7FFFFFFF'h, and increments until '7FFFFFFF'h.
-- Thus, a typical sequence number will be very negative.

ospfv3AsLsdbSequence OBJECT-TYPE
	SYNTAX  Ospfv3LsaSequenceTC
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The sequence number field is a signed 32-bit
		integer.  It is used to detect old and duplicate
		link state advertisements.  The space of
		sequence numbers is linearly ordered.  The
		larger the sequence number, the more recent the
		advertisement."
	REFERENCE
		"OSPF Version 2, Section 12.1.6, LS sequence
		number"
	-- 1.3.6.1.2.1.191.1.3.1.4
	::= { ospfv3AsLsdbEntry 4 }


ospfv3AsLsdbAge OBJECT-TYPE
	SYNTAX  Ospfv3LsaAgeTC
	UNITS	"seconds"
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"This field is the age of the link state
		advertisement in seconds.  The high-order bit
		of the LS age field is considered the DoNotAge
		bit for support of on-demand circuits."
	REFERENCE
		"OSPF Version 2, Section 12.1.1, LS age;
		Extending OSPF to Support Demand Circuits,
		Section 2.2, The LS age field."
	-- 1.3.6.1.2.1.191.1.3.1.5
	::= { ospfv3AsLsdbEntry 5 }


ospfv3AsLsdbChecksum OBJECT-TYPE
	SYNTAX  Integer32
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"This field is the checksum of the complete
		contents of the advertisement, excepting the
		age field.  The age field is excepted so that
		an advertisement's age can be incremented
		without updating the checksum.  The checksum
		used is the same that is used for ISO
		connectionless datagrams; it is commonly
		referred to as the Fletcher checksum."
	REFERENCE
		"OSPF Version 2, Section 12.1.7, LS checksum"
	-- 1.3.6.1.2.1.191.1.3.1.6
	::= { ospfv3AsLsdbEntry 6 }


ospfv3AsLsdbAdvertisement OBJECT-TYPE
	SYNTAX  OCTET STRING (SIZE (1..65535))
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The entire link state advertisement, including
		its header."
	-- 1.3.6.1.2.1.191.1.3.1.7
	::= { ospfv3AsLsdbEntry 7 }


ospfv3AsLsdbTypeKnown OBJECT-TYPE
	SYNTAX  TruthValue
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The value true (1) indicates that the LSA type
		is recognized by this router."
	-- 1.3.6.1.2.1.191.1.3.1.8
	::= { ospfv3AsLsdbEntry 8 }


--  OSPFv3 Area-Scope Link State Database

ospfv3AreaLsdbTable OBJECT-TYPE
	SYNTAX  SEQUENCE OF Ospfv3AreaLsdbEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"The OSPFv3 Process's Area-scope LSDB.
		The LSDB contains the Area-scope link state
		advertisements from throughout the area that the
		device is attached to."
	-- 1.3.6.1.2.1.191.1.4
	::= { ospfv3Objects 4 }


ospfv3AreaLsdbEntry OBJECT-TYPE
	SYNTAX  Ospfv3AreaLsdbEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"A single Area-scope link state advertisement."
	INDEX {
		ospfv3AreaLsdbAreaId,
		ospfv3AreaLsdbType,
		ospfv3AreaLsdbRouterId,
		ospfv3AreaLsdbLsid }
	-- 1.3.6.1.2.1.191.1.4.1
	::= { ospfv3AreaLsdbTable 1 }


Ospfv3AreaLsdbEntry ::= SEQUENCE {

	ospfv3AreaLsdbAreaId        Ospfv3AreaIdTC,
	ospfv3AreaLsdbType          Unsigned32,
	ospfv3AreaLsdbRouterId      Ospfv3RouterIdTC,
	ospfv3AreaLsdbLsid          Ospfv3LsIdTC,
	ospfv3AreaLsdbSequence      Ospfv3LsaSequenceTC,
	ospfv3AreaLsdbAge           Ospfv3LsaAgeTC,
	ospfv3AreaLsdbChecksum      Integer32,
	ospfv3AreaLsdbAdvertisement OCTET STRING,
	ospfv3AreaLsdbTypeKnown     TruthValue }


ospfv3AreaLsdbAreaId OBJECT-TYPE
	SYNTAX  Ospfv3AreaIdTC
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"The 32-bit identifier of the Area from which the
		LSA was received."
	REFERENCE
		"OSPF Version 2, Appendix C.2, Area parameters"
	-- 1.3.6.1.2.1.191.1.4.1.1
	::= { ospfv3AreaLsdbEntry 1 }


ospfv3AreaLsdbType OBJECT-TYPE
	SYNTAX  Unsigned32 (0..4294967295)
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"The type of the link state advertisement.
		Each link state type has a separate
		advertisement format.  Area-scope LSAs unrecognized
		by the router are also stored in this database."
	-- 1.3.6.1.2.1.191.1.4.1.2
	::= { ospfv3AreaLsdbEntry 2 }


ospfv3AreaLsdbRouterId OBJECT-TYPE
	SYNTAX  Ospfv3RouterIdTC
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"The 32-bit number that uniquely identifies the
		originating router in the Autonomous System."
	REFERENCE
		"OSPF Version 2, Appendix C.1, Global parameters"
	-- 1.3.6.1.2.1.191.1.4.1.3
	::= { ospfv3AreaLsdbEntry 3 }


ospfv3AreaLsdbLsid OBJECT-TYPE
	SYNTAX  Ospfv3LsIdTC
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"The Link State ID is an LS type-specific field
		containing a unique identifier;
		it identifies the piece of the routing domain
		that is being described by the advertisement.
		In contrast to OSPFv2, the LSID has no
		addressing semantics."
	-- 1.3.6.1.2.1.191.1.4.1.4
	::= { ospfv3AreaLsdbEntry 4 }


-- Note that the OSPF sequence number is a 32-bit signed
-- integer.  It starts with the value '80000001'h
-- or -'7FFFFFFF'h, and increments until '7FFFFFFF'h.
-- Thus, a typical sequence number will be very negative.

ospfv3AreaLsdbSequence OBJECT-TYPE
	SYNTAX  Ospfv3LsaSequenceTC
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The sequence number field is a signed 32-bit
		integer.  It is used to detect old and
		duplicate link state advertisements.  The space
		of sequence numbers is linearly ordered.  The
		larger the sequence number, the more recent the
		advertisement."
	REFERENCE
		"OSPF Version 2, Section 12.1.6, LS sequence
		number"
	-- 1.3.6.1.2.1.191.1.4.1.5
	::= { ospfv3AreaLsdbEntry 5 }


ospfv3AreaLsdbAge OBJECT-TYPE
	SYNTAX  Ospfv3LsaAgeTC
	UNITS	"seconds"
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"This field is the age of the link state
		advertisement in seconds.  The high-order bit
		of the LS age field is considered the DoNotAge
		bit for support of on-demand circuits."
	REFERENCE
		"OSPF Version 2, Section 12.1.1, LS age;
		Extending OSPF to Support Demand Circuits,
		Section 2.2, The LS age field."
	-- 1.3.6.1.2.1.191.1.4.1.6
	::= { ospfv3AreaLsdbEntry 6 }


ospfv3AreaLsdbChecksum OBJECT-TYPE
	SYNTAX  Integer32
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"This field is the checksum of the complete
		contents of the advertisement, excepting the
		age field.  The age field is excepted so that
		an advertisement's age can be incremented
		without updating the checksum.  The checksum
		used is the same that is used for ISO
		connectionless datagrams; it is commonly
		referred to as the Fletcher checksum."
	REFERENCE
		"OSPF Version 2, Section 12.1.7, LS checksum"
	-- 1.3.6.1.2.1.191.1.4.1.7
	::= { ospfv3AreaLsdbEntry 7 }


ospfv3AreaLsdbAdvertisement OBJECT-TYPE
	SYNTAX  OCTET STRING (SIZE (1..65535))
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The entire link state advertisement, including
		its header."
	-- 1.3.6.1.2.1.191.1.4.1.8
	::= { ospfv3AreaLsdbEntry 8 }


ospfv3AreaLsdbTypeKnown OBJECT-TYPE
	SYNTAX  TruthValue
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The value true (1) indicates that the LSA type is
		recognized by this router."
	-- 1.3.6.1.2.1.191.1.4.1.9
	::= { ospfv3AreaLsdbEntry 9 }


-- OSPFv3 Link-Scope Link State Database, for non-virtual interfaces

ospfv3LinkLsdbTable OBJECT-TYPE
	SYNTAX  SEQUENCE OF Ospfv3LinkLsdbEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"The OSPFv3 Process's Link-scope LSDB for non-virtual
		interfaces.  The LSDB contains the Link-scope link
		state advertisements from the interfaces that the
		device is attached to."
	-- 1.3.6.1.2.1.191.1.5
	::= { ospfv3Objects 5 }


ospfv3LinkLsdbEntry OBJECT-TYPE
	SYNTAX  Ospfv3LinkLsdbEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"A single Link-scope link state advertisement."
	INDEX {
		ospfv3LinkLsdbIfIndex,
		ospfv3LinkLsdbIfInstId,
		ospfv3LinkLsdbType,
		ospfv3LinkLsdbRouterId,
		ospfv3LinkLsdbLsid }
	-- 1.3.6.1.2.1.191.1.5.1
	::= { ospfv3LinkLsdbTable 1 }


Ospfv3LinkLsdbEntry ::= SEQUENCE {

	ospfv3LinkLsdbIfIndex       InterfaceIndex,
	ospfv3LinkLsdbIfInstId      Ospfv3IfInstIdTC,
	ospfv3LinkLsdbType          Unsigned32,
	ospfv3LinkLsdbRouterId      Ospfv3RouterIdTC,
	ospfv3LinkLsdbLsid          Ospfv3LsIdTC,
	ospfv3LinkLsdbSequence      Ospfv3LsaSequenceTC,
	ospfv3LinkLsdbAge           Ospfv3LsaAgeTC,
	ospfv3LinkLsdbChecksum      Integer32,
	ospfv3LinkLsdbAdvertisement OCTET STRING,
	ospfv3LinkLsdbTypeKnown     TruthValue }


ospfv3LinkLsdbIfIndex OBJECT-TYPE
	SYNTAX  InterfaceIndex
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"The identifier of the link from which the LSA
		was received."
	-- 1.3.6.1.2.1.191.1.5.1.1
	::= { ospfv3LinkLsdbEntry 1 }


ospfv3LinkLsdbIfInstId OBJECT-TYPE
	SYNTAX  Ospfv3IfInstIdTC
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"The identifier of the interface instance from
		which the LSA was received."
	-- 1.3.6.1.2.1.191.1.5.1.2
	::= { ospfv3LinkLsdbEntry 2 }


ospfv3LinkLsdbType OBJECT-TYPE
	SYNTAX  Unsigned32 (0..4294967295)
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"The type of the link state advertisement.
		Each link state type has a separate
		advertisement format.  Link-scope LSAs unrecognized
		by the router are also stored in this database."
	-- 1.3.6.1.2.1.191.1.5.1.3
	::= { ospfv3LinkLsdbEntry 3 }


ospfv3LinkLsdbRouterId OBJECT-TYPE
	SYNTAX  Ospfv3RouterIdTC
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"The 32-bit number that uniquely identifies the
		originating router in the Autonomous System."
	REFERENCE
		"OSPF Version 2, Appendix C.1, Global parameters"
	-- 1.3.6.1.2.1.191.1.5.1.4
	::= { ospfv3LinkLsdbEntry 4 }


ospfv3LinkLsdbLsid OBJECT-TYPE
	SYNTAX  Ospfv3LsIdTC
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"The Link State ID is an LS type-specific field
		containing a unique identifier;
		it identifies the piece of the routing domain
		that is being described by the advertisement.
		In contrast to OSPFv2, the LSID has no
		addressing semantics.  However, in OSPFv3
		the Link State ID always contains the flooding
		scope of the LSA."
	-- 1.3.6.1.2.1.191.1.5.1.5
	::= { ospfv3LinkLsdbEntry 5 }


-- Note that the OSPF sequence number is a 32-bit signed
-- integer.  It starts with the value '80000001'h
-- or -'7FFFFFFF'h, and increments until '7FFFFFFF'h.
-- Thus, a typical sequence number will be very negative.

ospfv3LinkLsdbSequence OBJECT-TYPE
	SYNTAX  Ospfv3LsaSequenceTC
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The sequence number field is a signed 32-bit
		integer.  It is used to detect old and duplicate
		link state advertisements.  The space of
		sequence numbers is linearly ordered.  The
		larger the sequence number, the more recent the
		advertisement."
	REFERENCE
		"OSPF Version 2, Section 12.1.6, LS sequence
		number"
	-- 1.3.6.1.2.1.191.1.5.1.6
	::= { ospfv3LinkLsdbEntry 6 }


ospfv3LinkLsdbAge OBJECT-TYPE
	SYNTAX  Ospfv3LsaAgeTC
	UNITS	"seconds"
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"This field is the age of the link state
		advertisement in seconds.  The high-order bit
		of the LS age field is considered the DoNotAge
		bit for support of on-demand circuits."
	REFERENCE
		"OSPF Version 2, Section 12.1.1, LS age;
		Extending OSPF to Support Demand Circuits,
		Section 2.2, The LS age field."
	-- 1.3.6.1.2.1.191.1.5.1.7
	::= { ospfv3LinkLsdbEntry 7 }


ospfv3LinkLsdbChecksum OBJECT-TYPE
	SYNTAX  Integer32
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"This field is the checksum of the complete
		contents of the advertisement, excepting the
		age field.  The age field is excepted so that
		an advertisement's age can be incremented
		without updating the checksum.  The checksum
		used is the same that is used for ISO
		connectionless datagrams; it is commonly
		referred to as the Fletcher checksum."
	REFERENCE
		"OSPF Version 2, Section 12.1.7, LS checksum"
	-- 1.3.6.1.2.1.191.1.5.1.8
	::= { ospfv3LinkLsdbEntry 8 }


ospfv3LinkLsdbAdvertisement OBJECT-TYPE
	SYNTAX  OCTET STRING (SIZE (1..65535))
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The entire link state advertisement, including
		its header."
	-- 1.3.6.1.2.1.191.1.5.1.9
	::= { ospfv3LinkLsdbEntry 9 }


ospfv3LinkLsdbTypeKnown OBJECT-TYPE
	SYNTAX  TruthValue
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The value true (1) indicates that the LSA type is
		recognized by this router."
	-- 1.3.6.1.2.1.191.1.5.1.10
	::= { ospfv3LinkLsdbEntry 10 }


-- OSPF Host Table

ospfv3HostTable OBJECT-TYPE
	SYNTAX  SEQUENCE OF Ospfv3HostEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"The Host/Metric Table indicates what hosts are
		directly attached to the router and their
		corresponding metrics."
	REFERENCE
		"OSPF Version 2, Appendix C.7, Host route
		parameters"
	-- 1.3.6.1.2.1.191.1.6
	::= { ospfv3Objects 6 }


ospfv3HostEntry OBJECT-TYPE
	SYNTAX  Ospfv3HostEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"A metric to be advertised when a given host is
		reachable.

		The information in this table is persistent, and
		when written, the entity SHOULD save the change
		to non-volatile storage."
	INDEX {
		ospfv3HostAddressType,
		ospfv3HostAddress }
	-- 1.3.6.1.2.1.191.1.6.1
	::= { ospfv3HostTable 1 }


Ospfv3HostEntry ::= SEQUENCE {

	ospfv3HostAddressType InetAddressType,
	ospfv3HostAddress     InetAddress,
	ospfv3HostMetric      Metric,
	ospfv3HostRowStatus   RowStatus,
	ospfv3HostAreaID      Ospfv3AreaIdTC }


ospfv3HostAddressType OBJECT-TYPE
	SYNTAX  InetAddressType
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"The address type of ospfv3HostAddress.  Only IPv6
		global address type is expected."
	REFERENCE
		"OSPF Version 2, Appendix C.7, Host route
		parameters"
	-- 1.3.6.1.2.1.191.1.6.1.1
	::= { ospfv3HostEntry 1 }


ospfv3HostAddress OBJECT-TYPE
	SYNTAX  InetAddress
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"The IPv6 address of the host.  Must be an
		IPv6 global address."
	REFERENCE
		"OSPF Version 2, Appendix C.7, Host route
		parameters"
	-- 1.3.6.1.2.1.191.1.6.1.2
	::= { ospfv3HostEntry 2 }


ospfv3HostMetric OBJECT-TYPE
	SYNTAX  Metric
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"The metric to be advertised."
	REFERENCE
		"OSPF Version 2, Appendix C.7, Host route
		parameters"
	-- 1.3.6.1.2.1.191.1.6.1.3
	::= { ospfv3HostEntry 3 }


ospfv3HostRowStatus OBJECT-TYPE
	SYNTAX  RowStatus
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"This object permits management of the table by
		facilitating actions such as row creation,
		construction, and destruction.

		The value of this object has no effect on
		whether other objects in this conceptual row can be
		modified."
	-- 1.3.6.1.2.1.191.1.6.1.4
	::= { ospfv3HostEntry 4 }


ospfv3HostAreaID OBJECT-TYPE
	SYNTAX  Ospfv3AreaIdTC
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"The Area the host entry is to be found within.
		By default, the area for the subsuming OSPFv3
		interface, or Area 0 if there is no subsuming
		interface."
	REFERENCE
		"OSPF Version 2, Appendix C.2, Area parameters"
	-- 1.3.6.1.2.1.191.1.6.1.5
	::= { ospfv3HostEntry 5 }


-- OSPFv3 Interface Table

ospfv3IfTable OBJECT-TYPE
	SYNTAX  SEQUENCE OF Ospfv3IfEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"The OSPFv3 Interface Table describes the
		interfaces from the viewpoint of OSPFv3."
	REFERENCE
		"OSPF for IPv6, Appendix C.3, Router Interface
		Parameters"
	-- 1.3.6.1.2.1.191.1.7
	::= { ospfv3Objects 7 }


ospfv3IfEntry OBJECT-TYPE
	SYNTAX  Ospfv3IfEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"The OSPFv3 Interface Entry describes one
		interface from the viewpoint of OSPFv3.

		The information in this table is persistent,
		and when written, the entity SHOULD save the
		change to non-volatile storage."
	INDEX {
		ospfv3IfIndex,
		ospfv3IfInstId }
	-- 1.3.6.1.2.1.191.1.7.1
	::= { ospfv3IfTable 1 }


Ospfv3IfEntry ::= SEQUENCE {

	ospfv3IfIndex                      InterfaceIndex,
	ospfv3IfInstId                     Ospfv3IfInstIdTC,
	ospfv3IfAreaId                     Ospfv3AreaIdTC,
	ospfv3IfType                       INTEGER,
	ospfv3IfAdminStatus                Status,
	ospfv3IfRtrPriority                DesignatedRouterPriority,
	ospfv3IfTransitDelay               Ospfv3UpToRefreshIntervalTC,
	ospfv3IfRetransInterval            Ospfv3UpToRefreshIntervalTC,
	ospfv3IfHelloInterval              HelloRange,
	ospfv3IfRtrDeadInterval            Ospfv3DeadIntervalRangeTC,
	ospfv3IfPollInterval               Unsigned32,
	ospfv3IfState                      INTEGER,
	ospfv3IfDesignatedRouter           Ospfv3RouterIdTC,
	ospfv3IfBackupDesignatedRouter     Ospfv3RouterIdTC,
	ospfv3IfEvents                     Counter32,
	ospfv3IfRowStatus                  RowStatus,
	ospfv3IfDemand                     TruthValue,
	ospfv3IfMetricValue                Metric,
	ospfv3IfLinkScopeLsaCount          Gauge32,
	ospfv3IfLinkLsaCksumSum            Unsigned32,
	ospfv3IfDemandNbrProbe             TruthValue,
	ospfv3IfDemandNbrProbeRetransLimit Unsigned32,
	ospfv3IfDemandNbrProbeInterval     Unsigned32,
	ospfv3IfTEDisabled                 TruthValue,
	ospfv3IfLinkLSASuppression         TruthValue }


ospfv3IfIndex OBJECT-TYPE
	SYNTAX  InterfaceIndex
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"The interface index of this OSPFv3 interface.
		It corresponds to the interface index of the
		IPv6 interface on which OSPFv3 is configured."
	-- 1.3.6.1.2.1.191.1.7.1.1
	::= { ospfv3IfEntry 1 }


ospfv3IfInstId OBJECT-TYPE
	SYNTAX  Ospfv3IfInstIdTC
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"Enables multiple interface instances of OSPFv3
		to be run over a single link.  Each interface
		instance would be assigned a separate ID.  This ID
		has local link significance only."
	-- 1.3.6.1.2.1.191.1.7.1.2
	::= { ospfv3IfEntry 2 }


ospfv3IfAreaId OBJECT-TYPE
	SYNTAX  Ospfv3AreaIdTC
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"A 32-bit integer uniquely identifying the area
		to which the interface connects.  Area ID
		0 is used for the OSPFv3 backbone."
	DEFVAL { 0 }
	-- 1.3.6.1.2.1.191.1.7.1.3
	::= { ospfv3IfEntry 3 }


ospfv3IfType OBJECT-TYPE
	SYNTAX  INTEGER {
			broadcast(1),
			nbma(2),
			pointToPoint(3),
			pointToMultipoint(5) }
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"The OSPFv3 interface type."
	-- 1.3.6.1.2.1.191.1.7.1.4
	::= { ospfv3IfEntry 4 }


ospfv3IfAdminStatus OBJECT-TYPE
	SYNTAX  Status
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"The OSPFv3 interface's administrative status.
		The value formed on the interface; the interface
		will be advertised as an internal route to some
		area.  The value 'disabled' denotes that the
		interface is external to OSPFv3.








		Note that a value of 'disabled' for the object
		ospfv3AdminStatus will override a value of
		'enabled' for the interface."
	DEFVAL { enabled }
	-- 1.3.6.1.2.1.191.1.7.1.5
	::= { ospfv3IfEntry 5 }


ospfv3IfRtrPriority OBJECT-TYPE
	SYNTAX  DesignatedRouterPriority
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"The priority of this interface.  Used in
		multi-access networks, this field is used in
		the designated-router election algorithm.  The
		value 0 signifies that the router is not
		eligible to become the Designated Router on this
		particular network.  In the event of a tie in
		this value, routers will use their Router ID as
		a tie breaker."
	DEFVAL { 1 }
	-- 1.3.6.1.2.1.191.1.7.1.6
	::= { ospfv3IfEntry 6 }


ospfv3IfTransitDelay OBJECT-TYPE
	SYNTAX  Ospfv3UpToRefreshIntervalTC
	UNITS	"seconds"
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"The estimated number of seconds it takes to transmit
		a Link State Update packet over this interface.  LSAs
		contained in the update packet must have their age
		incremented by this amount before transmission.  This
		value should take into account the transmission and
		propagation delays of the interface."
	REFERENCE
		"OSPF for IPv6, Appendix C.3, Router Interface
		Parameters."
	DEFVAL { 1 }
	-- 1.3.6.1.2.1.191.1.7.1.7
	::= { ospfv3IfEntry 7 }


ospfv3IfRetransInterval OBJECT-TYPE
	SYNTAX  Ospfv3UpToRefreshIntervalTC
	UNITS	"seconds"
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"The number of seconds between link state
		advertisement retransmissions for adjacencies





		belonging to this interface.  This value is
		also used when retransmitting database
		description and Link State Request packets."
	DEFVAL { 5 }
	-- 1.3.6.1.2.1.191.1.7.1.8
	::= { ospfv3IfEntry 8 }


ospfv3IfHelloInterval OBJECT-TYPE
	SYNTAX  HelloRange
	UNITS	"seconds"
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"The length of time, in seconds, between the
		Hello packets that the router sends on the
		interface.  This value must be the same for all
		routers attached to a common network."
	DEFVAL { 10 }
	-- 1.3.6.1.2.1.191.1.7.1.9
	::= { ospfv3IfEntry 9 }


ospfv3IfRtrDeadInterval OBJECT-TYPE
	SYNTAX  Ospfv3DeadIntervalRangeTC
	UNITS	"seconds"
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"The number of seconds that a router's Hello
		packets have not been seen before its
		neighbors declare the router down on the interface.
		This should be some multiple of the Hello interval.
		This value must be the same for all routers attached
		to a common network."
	DEFVAL { 40 }
	-- 1.3.6.1.2.1.191.1.7.1.10
	::= { ospfv3IfEntry 10 }


ospfv3IfPollInterval OBJECT-TYPE
	SYNTAX  Unsigned32
	UNITS	"seconds"
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"The larger time interval, in seconds, between
		the Hello packets sent to an inactive,
		non-broadcast multi-access neighbor."
	DEFVAL { 120 }
	-- 1.3.6.1.2.1.191.1.7.1.11
	::= { ospfv3IfEntry 11 }


ospfv3IfState OBJECT-TYPE
	SYNTAX  INTEGER {
			down(1),
			loopback(2),
			waiting(3),
			pointToPoint(4),
			designatedRouter(5),
			backupDesignatedRouter(6),
			otherDesignatedRouter(7),
			standby(8) }
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The OSPFv3 interface state.  An interface may be
		in standby state if there are multiple interfaces
		on the link and another interface is active.  The
		interface may be in Down state if the underlying
		IPv6 interface is down or if the admin status is
		'disabled' either globally or for the interface."
	-- 1.3.6.1.2.1.191.1.7.1.12
	::= { ospfv3IfEntry 12 }


ospfv3IfDesignatedRouter OBJECT-TYPE
	SYNTAX  Ospfv3RouterIdTC
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The Router ID of the Designated Router."
	-- 1.3.6.1.2.1.191.1.7.1.13
	::= { ospfv3IfEntry 13 }


ospfv3IfBackupDesignatedRouter OBJECT-TYPE
	SYNTAX  Ospfv3RouterIdTC
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The Router ID of the Backup Designated
		Router."
	-- 1.3.6.1.2.1.191.1.7.1.14
	::= { ospfv3IfEntry 14 }


ospfv3IfEvents OBJECT-TYPE
	SYNTAX  Counter32
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The number of times this OSPFv3 interface has
		changed its state or an error has occurred.







		Discontinuities in the value of this counter
		can occur at re-initialization of the management
		system and at other times as indicated by the
		value of ospfv3DiscontinuityTime."
	-- 1.3.6.1.2.1.191.1.7.1.15
	::= { ospfv3IfEntry 15 }


ospfv3IfRowStatus OBJECT-TYPE
	SYNTAX  RowStatus
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"This object permits management of the table by
		facilitating actions such as row creation,
		construction, and destruction.

		The value of this object has no effect on
		whether other objects in this conceptual row can be
		modified."
	-- 1.3.6.1.2.1.191.1.7.1.16
	::= { ospfv3IfEntry 16 }


ospfv3IfDemand OBJECT-TYPE
	SYNTAX  TruthValue
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"Indicates whether Demand OSPFv3 procedures
		(Hello suppression to FULL neighbors and
		setting the DoNotAge flag on propagated LSAs)
		should be performed on this interface."
	DEFVAL { false }
	-- 1.3.6.1.2.1.191.1.7.1.17
	::= { ospfv3IfEntry 17 }


ospfv3IfMetricValue OBJECT-TYPE
	SYNTAX  Metric
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"The metric assigned to this interface.
		The default value of the metric is
		'Reference Bandwidth / ifSpeed'.  The value
		of the reference bandwidth can be set
		in the ospfv3ReferenceBandwidth object."
	-- 1.3.6.1.2.1.191.1.7.1.18
	::= { ospfv3IfEntry 18 }


ospfv3IfLinkScopeLsaCount OBJECT-TYPE
	SYNTAX  Gauge32
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The total number of Link-scope link state
		advertisements in this link's link state
		database."
	-- 1.3.6.1.2.1.191.1.7.1.19
	::= { ospfv3IfEntry 19 }


ospfv3IfLinkLsaCksumSum OBJECT-TYPE
	SYNTAX  Unsigned32
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The 32-bit unsigned sum of the Link-scope link state
		advertisements' LS checksums contained in this
		link's link state database.  The sum can be used
		to determine if there has been a change in a
		router's link state database or to compare the
		link state database of two routers."
	-- 1.3.6.1.2.1.191.1.7.1.20
	::= { ospfv3IfEntry 20 }


ospfv3IfDemandNbrProbe OBJECT-TYPE
	SYNTAX  TruthValue
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"Indicates whether or not neighbor probing is
		enabled to determine whether or not the neighbor
		is inactive.  Neighbor probing is disabled by
		default."
	DEFVAL { false }
	-- 1.3.6.1.2.1.191.1.7.1.21
	::= { ospfv3IfEntry 21 }


ospfv3IfDemandNbrProbeRetransLimit OBJECT-TYPE
	SYNTAX  Unsigned32
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"The number of consecutive LSA retransmissions before
		the neighbor is deemed inactive and the neighbor
		adjacency is brought down."
	DEFVAL { 10 }
	-- 1.3.6.1.2.1.191.1.7.1.22
	::= { ospfv3IfEntry 22 }


ospfv3IfDemandNbrProbeInterval OBJECT-TYPE
	SYNTAX  Unsigned32
	UNITS	"seconds"
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"Defines how often the neighbor will be probed."
	DEFVAL { 120 }
	-- 1.3.6.1.2.1.191.1.7.1.23
	::= { ospfv3IfEntry 23 }


ospfv3IfTEDisabled OBJECT-TYPE
	SYNTAX  TruthValue
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"Indicates whether or not traffic engineering
		is disabled on the interface when traffic
		engineering is enabled in the area where the
		interface is attached.  The object is set
		to the value true (1) to disable traffic engineering
		on the interface.  Traffic engineering is enabled
		by default on the interface when traffic engineering
		is enabled in the area where the interface is
		attached."
	DEFVAL { false }
	-- 1.3.6.1.2.1.191.1.7.1.24
	::= { ospfv3IfEntry 24 }


ospfv3IfLinkLSASuppression OBJECT-TYPE
	SYNTAX  TruthValue
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"Specifies whether or not link LSA origination is
		suppressed for broadcast or NBMA interface types.
		The object is set to value true (1) to suppress
		the origination."
	REFERENCE
		"OSPF for IPv6, Appendix C.3, Router Interface
		Parameters"
	DEFVAL { false }
	-- 1.3.6.1.2.1.191.1.7.1.25
	::= { ospfv3IfEntry 25 }


-- OSPFv3 Virtual Interface Table

ospfv3VirtIfTable OBJECT-TYPE
	SYNTAX  SEQUENCE OF Ospfv3VirtIfEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"Information about this router's virtual
		interfaces that the OSPFv3 Process is configured
		to carry on."
	REFERENCE
		"OSPF for IPv6, Appendix C.4, Virtual Link
		Parameters"
	-- 1.3.6.1.2.1.191.1.8
	::= { ospfv3Objects 8 }


ospfv3VirtIfEntry OBJECT-TYPE
	SYNTAX  Ospfv3VirtIfEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"Information about a single virtual interface.

		The information in this table is persistent,
		and when written, the entity SHOULD save the
		change to non-volatile storage."
	INDEX {
		ospfv3VirtIfAreaId,
		ospfv3VirtIfNeighbor }
	-- 1.3.6.1.2.1.191.1.8.1
	::= { ospfv3VirtIfTable 1 }


Ospfv3VirtIfEntry ::= SEQUENCE {

	ospfv3VirtIfAreaId            Ospfv3AreaIdTC,
	ospfv3VirtIfNeighbor          Ospfv3RouterIdTC,
	ospfv3VirtIfIndex             InterfaceIndex,
	ospfv3VirtIfInstId            Ospfv3IfInstIdTC,
	ospfv3VirtIfTransitDelay      Ospfv3UpToRefreshIntervalTC,
	ospfv3VirtIfRetransInterval   Ospfv3UpToRefreshIntervalTC,
	ospfv3VirtIfHelloInterval     HelloRange,
	ospfv3VirtIfRtrDeadInterval   Ospfv3DeadIntervalRangeTC,
	ospfv3VirtIfState             INTEGER,
	ospfv3VirtIfEvents            Counter32,
	ospfv3VirtIfRowStatus         RowStatus,
	ospfv3VirtIfLinkScopeLsaCount Gauge32,
	ospfv3VirtIfLinkLsaCksumSum   Unsigned32 }


ospfv3VirtIfAreaId OBJECT-TYPE
	SYNTAX  Ospfv3AreaIdTC
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"The transit area that the virtual link
		traverses.  By definition, this is not
		Area 0."
	-- 1.3.6.1.2.1.191.1.8.1.1
	::= { ospfv3VirtIfEntry 1 }


ospfv3VirtIfNeighbor OBJECT-TYPE
	SYNTAX  Ospfv3RouterIdTC
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"The Router ID of the virtual neighbor."
	-- 1.3.6.1.2.1.191.1.8.1.2
	::= { ospfv3VirtIfEntry 2 }


ospfv3VirtIfIndex OBJECT-TYPE
	SYNTAX  InterfaceIndex
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The local interface index assigned by the
		OSPFv3 Process to this OSPFv3 virtual interface.
		It is advertised in Hellos sent over the virtual
		link and in the router's router-LSAs."
	-- 1.3.6.1.2.1.191.1.8.1.3
	::= { ospfv3VirtIfEntry 3 }


ospfv3VirtIfInstId OBJECT-TYPE
	SYNTAX  Ospfv3IfInstIdTC
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The local Interface Instance ID assigned by the
		OSPFv3 Process to this OSPFv3 virtual interface."
	-- 1.3.6.1.2.1.191.1.8.1.4
	::= { ospfv3VirtIfEntry 4 }


ospfv3VirtIfTransitDelay OBJECT-TYPE
	SYNTAX  Ospfv3UpToRefreshIntervalTC
	UNITS	"seconds"
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"The estimated number of seconds it takes to
		transmit a Link State Update packet over this
		interface."
	DEFVAL { 1 }
	-- 1.3.6.1.2.1.191.1.8.1.5
	::= { ospfv3VirtIfEntry 5 }


ospfv3VirtIfRetransInterval OBJECT-TYPE
	SYNTAX  Ospfv3UpToRefreshIntervalTC
	UNITS	"seconds"
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"The number of seconds between link state
		advertisement retransmissions for adjacencies
		belonging to this interface.  This value is
		also used when retransmitting database
		description and Link State Request packets.  This
		value should be well over the expected
		round-trip time."
	DEFVAL { 5 }
	-- 1.3.6.1.2.1.191.1.8.1.6
	::= { ospfv3VirtIfEntry 6 }


ospfv3VirtIfHelloInterval OBJECT-TYPE
	SYNTAX  HelloRange
	UNITS	"seconds"
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"The length of time, in seconds, between the
		Hello packets that the router sends on the
		interface.  This value must be the same for the
		virtual neighbor."
	DEFVAL { 10 }
	-- 1.3.6.1.2.1.191.1.8.1.7
	::= { ospfv3VirtIfEntry 7 }


ospfv3VirtIfRtrDeadInterval OBJECT-TYPE
	SYNTAX  Ospfv3DeadIntervalRangeTC
	UNITS	"seconds"
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"The number of seconds that a router's Hello
		packets have not been seen before its
		neighbors declare the router down.  This should
		be some multiple of the Hello interval.  This
		value must be the same for the virtual
		neighbor."
	DEFVAL { 60 }
	-- 1.3.6.1.2.1.191.1.8.1.8
	::= { ospfv3VirtIfEntry 8 }


ospfv3VirtIfState OBJECT-TYPE
	SYNTAX  INTEGER {
			down(1),
			pointToPoint(4) }
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"OSPF virtual interface states.  The same encoding
		as the ospfV3IfTable is used."
	-- 1.3.6.1.2.1.191.1.8.1.9
	::= { ospfv3VirtIfEntry 9 }


ospfv3VirtIfEvents OBJECT-TYPE
	SYNTAX  Counter32
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The number of state changes or error events on
		this virtual link.

		Discontinuities in the value of this counter
		can occur at re-initialization of the management
		system and at other times as indicated by the
		value of ospfv3DiscontinuityTime."
	-- 1.3.6.1.2.1.191.1.8.1.10
	::= { ospfv3VirtIfEntry 10 }


ospfv3VirtIfRowStatus OBJECT-TYPE
	SYNTAX  RowStatus
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"This object permits management of the table by
		facilitating actions such as row creation,
		construction, and destruction.

		The value of this object has no effect on
		whether other objects in this conceptual row can be
		modified."
	-- 1.3.6.1.2.1.191.1.8.1.11
	::= { ospfv3VirtIfEntry 11 }


ospfv3VirtIfLinkScopeLsaCount OBJECT-TYPE
	SYNTAX  Gauge32
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The total number of Link-scope link state
		advertisements in this virtual link's link state
		database."
	-- 1.3.6.1.2.1.191.1.8.1.12
	::= { ospfv3VirtIfEntry 12 }


ospfv3VirtIfLinkLsaCksumSum OBJECT-TYPE
	SYNTAX  Unsigned32
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The 32-bit unsigned sum of the Link-scope link state
		advertisements' LS checksums contained in this
		virtual link's link state database.  The sum can be used
		to determine if there has been a change in a
		router's link state database or to compare the
		link state database of two routers."
	-- 1.3.6.1.2.1.191.1.8.1.13
	::= { ospfv3VirtIfEntry 13 }


-- OSPFv3 Neighbor Table

ospfv3NbrTable OBJECT-TYPE
	SYNTAX  SEQUENCE OF Ospfv3NbrEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"A table describing all neighbors in the
		locality of the OSPFv3 router."
	REFERENCE
		"OSPF Version 2, Section 10, The Neighbor Data
		Structure"
	-- 1.3.6.1.2.1.191.1.9
	::= { ospfv3Objects 9 }


ospfv3NbrEntry OBJECT-TYPE
	SYNTAX  Ospfv3NbrEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"The information regarding a single neighbor."
	REFERENCE
		"OSPF Version 2, Section 10, The Neighbor Data
		Structure"
	INDEX {
		ospfv3NbrIfIndex,
		ospfv3NbrIfInstId,
		ospfv3NbrRtrId }
	-- 1.3.6.1.2.1.191.1.9.1
	::= { ospfv3NbrTable 1 }


Ospfv3NbrEntry ::= SEQUENCE {

	ospfv3NbrIfIndex                 InterfaceIndex,
	ospfv3NbrIfInstId                Ospfv3IfInstIdTC,
	ospfv3NbrRtrId                   Ospfv3RouterIdTC,
	ospfv3NbrAddressType             InetAddressType,
	ospfv3NbrAddress                 InetAddress,
	ospfv3NbrOptions                 Integer32,
	ospfv3NbrPriority                DesignatedRouterPriority,
	ospfv3NbrState                   INTEGER,
	ospfv3NbrEvents                  Counter32,
	ospfv3NbrLsRetransQLen           Gauge32,
	ospfv3NbrHelloSuppressed         TruthValue,
	ospfv3NbrIfId                    InterfaceIndex,
	ospfv3NbrRestartHelperStatus     INTEGER,
	ospfv3NbrRestartHelperAge        Ospfv3UpToRefreshIntervalTC,
	ospfv3NbrRestartHelperExitReason INTEGER }


ospfv3NbrIfIndex OBJECT-TYPE
	SYNTAX  InterfaceIndex
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"The Local Link ID of the link over which the
		neighbor can be reached."
	-- 1.3.6.1.2.1.191.1.9.1.1
	::= { ospfv3NbrEntry 1 }


ospfv3NbrIfInstId OBJECT-TYPE
	SYNTAX  Ospfv3IfInstIdTC
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"Interface instance over which the neighbor
		can be reached.  This ID has local link
		significance only."
	-- 1.3.6.1.2.1.191.1.9.1.2
	::= { ospfv3NbrEntry 2 }


ospfv3NbrRtrId OBJECT-TYPE
	SYNTAX  Ospfv3RouterIdTC
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"A 32-bit unsigned integer uniquely identifying the
		neighboring router in the Autonomous System."
	-- 1.3.6.1.2.1.191.1.9.1.3
	::= { ospfv3NbrEntry 3 }


ospfv3NbrAddressType OBJECT-TYPE
	SYNTAX  InetAddressType
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The address type of ospfv3NbrAddress.  Only IPv6
		addresses without zone index are expected."
	-- 1.3.6.1.2.1.191.1.9.1.4
	::= { ospfv3NbrEntry 4 }


ospfv3NbrAddress OBJECT-TYPE
	SYNTAX  InetAddress
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The IPv6 address of the neighbor associated with
		the local link."
	-- 1.3.6.1.2.1.191.1.9.1.5
	::= { ospfv3NbrEntry 5 }


ospfv3NbrOptions OBJECT-TYPE
	SYNTAX  Integer32
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"A bit mask corresponding to the neighbor's
		options field."
	REFERENCE
		"OSPF for IPv6, Appendix A.2, The Options Field"
	-- 1.3.6.1.2.1.191.1.9.1.6
	::= { ospfv3NbrEntry 6 }


ospfv3NbrPriority OBJECT-TYPE
	SYNTAX  DesignatedRouterPriority
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The priority of this neighbor in the designated-
		router election algorithm.  The value 0 signifies
		that the neighbor is not eligible to become the
		Designated Router on this particular network."
	-- 1.3.6.1.2.1.191.1.9.1.7
	::= { ospfv3NbrEntry 7 }


ospfv3NbrState OBJECT-TYPE
	SYNTAX  INTEGER {
			down(1),
			attempt(2),
			init(3),
			twoWay(4),
			exchangeStart(5),
			exchange(6),
			loading(7),
			full(8) }
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The state of the relationship with this
		neighbor."
	REFERENCE
		"OSPF Version 2, Section 10.1, Neighbor states"
	-- 1.3.6.1.2.1.191.1.9.1.8
	::= { ospfv3NbrEntry 8 }


ospfv3NbrEvents OBJECT-TYPE
	SYNTAX  Counter32
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The number of times this neighbor relationship
		has changed state or an error has occurred.

		Discontinuities in the value of this counter
		can occur at re-initialization of the management
		system and at other times as indicated by the
		value of ospfv3DiscontinuityTime."
	-- 1.3.6.1.2.1.191.1.9.1.9
	::= { ospfv3NbrEntry 9 }


ospfv3NbrLsRetransQLen OBJECT-TYPE
	SYNTAX  Gauge32
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The current length of the retransmission
		queue."
	-- 1.3.6.1.2.1.191.1.9.1.10
	::= { ospfv3NbrEntry 10 }


ospfv3NbrHelloSuppressed OBJECT-TYPE
	SYNTAX  TruthValue
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Indicates whether Hellos are being suppressed
		to the neighbor."
	-- 1.3.6.1.2.1.191.1.9.1.11
	::= { ospfv3NbrEntry 11 }


ospfv3NbrIfId OBJECT-TYPE
	SYNTAX  InterfaceIndex
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The Interface ID that the neighbor advertises
		in its Hello packets on this link, that is, the
		neighbor's local interface index."
	-- 1.3.6.1.2.1.191.1.9.1.12
	::= { ospfv3NbrEntry 12 }


ospfv3NbrRestartHelperStatus OBJECT-TYPE
	SYNTAX  INTEGER {
			notHelping(1),
			helping(2) }
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Indicates whether the router is acting
		as a graceful restart helper for the neighbor."
	-- 1.3.6.1.2.1.191.1.9.1.13
	::= { ospfv3NbrEntry 13 }


ospfv3NbrRestartHelperAge OBJECT-TYPE
	SYNTAX  Ospfv3UpToRefreshIntervalTC
	UNITS	"seconds"
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Remaining time in current OSPF graceful restart
		interval, if the router is acting as a restart
		helper for the neighbor."
	-- 1.3.6.1.2.1.191.1.9.1.14
	::= { ospfv3NbrEntry 14 }


ospfv3NbrRestartHelperExitReason OBJECT-TYPE
	SYNTAX  INTEGER {
			none(1),
			inProgress(2),
			completed(3),
			timedOut(4),
			topologyChanged(5) }
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Describes the outcome of the last attempt at acting
		as a graceful restart helper for the neighbor.

		none:            no restart has yet been attempted.
		inProgress:      a restart attempt is currently underway.
		completed:       the last restart completed successfully.
		timedOut:        the last restart timed out.
		topologyChanged: the last restart was aborted due to
		                 a topology change."
	-- 1.3.6.1.2.1.191.1.9.1.15
	::= { ospfv3NbrEntry 15 }


-- OSPFv3 Configured Neighbor Table

ospfv3CfgNbrTable OBJECT-TYPE
	SYNTAX  SEQUENCE OF Ospfv3CfgNbrEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"A table describing all configured neighbors.

		The Configured Neighbors table just gives
		OSPFv3 information for sending OSPFv3 packets
		to potential neighbors and is typically used
		on NBMA and Point-to-Multipoint networks.
		Once a Hello is received from a neighbor in
		the Configured Neighbor table, an entry for
		that neighbor is created in the Neighbor table
		and adjacency state is maintained there.
		Neighbors on multi-access or Point-to-Point
		networks can use multicast addressing, so only
		Neighbor table entries are created for them."
	REFERENCE
		"OSPF Version 2, Section 10, The Neighbor Data
		Structure"
	-- 1.3.6.1.2.1.191.1.10
	::= { ospfv3Objects 10 }


ospfv3CfgNbrEntry OBJECT-TYPE
	SYNTAX  Ospfv3CfgNbrEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"The information regarding a single configured
		neighbor.

		The information in this table is persistent,
		and when written, the entity SHOULD save the
		change to non-volatile storage."
	REFERENCE
		"OSPF Version 2, Section 10, The Neighbor Data
		Structure"
	INDEX {
		ospfv3CfgNbrIfIndex,
		ospfv3CfgNbrIfInstId,
		ospfv3CfgNbrAddressType,
		ospfv3CfgNbrAddress }
	-- 1.3.6.1.2.1.191.1.10.1
	::= { ospfv3CfgNbrTable 1 }


Ospfv3CfgNbrEntry ::= SEQUENCE {

	ospfv3CfgNbrIfIndex     InterfaceIndex,
	ospfv3CfgNbrIfInstId    Ospfv3IfInstIdTC,
	ospfv3CfgNbrAddressType InetAddressType,
	ospfv3CfgNbrAddress     InetAddress,
	ospfv3CfgNbrPriority    DesignatedRouterPriority,
	ospfv3CfgNbrRowStatus   RowStatus }


ospfv3CfgNbrIfIndex OBJECT-TYPE
	SYNTAX  InterfaceIndex
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"The Local Link ID of the link over which the
		neighbor can be reached."
	-- 1.3.6.1.2.1.191.1.10.1.1
	::= { ospfv3CfgNbrEntry 1 }


ospfv3CfgNbrIfInstId OBJECT-TYPE
	SYNTAX  Ospfv3IfInstIdTC
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"Interface instance over which the neighbor
		can be reached.  This ID has local link
		significance only."
	-- 1.3.6.1.2.1.191.1.10.1.2
	::= { ospfv3CfgNbrEntry 2 }


ospfv3CfgNbrAddressType OBJECT-TYPE
	SYNTAX  InetAddressType
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"The address type of ospfv3NbrAddress.  Only IPv6
		addresses without zone index are expected."
	-- 1.3.6.1.2.1.191.1.10.1.3
	::= { ospfv3CfgNbrEntry 3 }


ospfv3CfgNbrAddress OBJECT-TYPE
	SYNTAX  InetAddress
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"The IPv6 address of the neighbor associated with
		the local link."
	-- 1.3.6.1.2.1.191.1.10.1.4
	::= { ospfv3CfgNbrEntry 4 }


ospfv3CfgNbrPriority OBJECT-TYPE
	SYNTAX  DesignatedRouterPriority
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"The priority of this neighbor in the designated-
		router election algorithm.  The value 0 signifies
		that the neighbor is not eligible to become the
		Designated Router on this particular network."
	DEFVAL { 1 }
	-- 1.3.6.1.2.1.191.1.10.1.5
	::= { ospfv3CfgNbrEntry 5 }


ospfv3CfgNbrRowStatus OBJECT-TYPE
	SYNTAX  RowStatus
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"This object permits management of the table by
		facilitating actions such as row creation,
		construction, and destruction.

		The value of this object has no effect on
		whether other objects in this conceptual row can be
		modified."
	-- 1.3.6.1.2.1.191.1.10.1.6
	::= { ospfv3CfgNbrEntry 6 }


-- OSPFv3 Virtual Neighbor Table

ospfv3VirtNbrTable OBJECT-TYPE
	SYNTAX  SEQUENCE OF Ospfv3VirtNbrEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"A table describing all virtual neighbors."
	REFERENCE
		"OSPF Version 2, Section 15, Virtual Links"
	-- 1.3.6.1.2.1.191.1.11
	::= { ospfv3Objects 11 }


ospfv3VirtNbrEntry OBJECT-TYPE
	SYNTAX  Ospfv3VirtNbrEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"Virtual neighbor information."
	INDEX {
		ospfv3VirtNbrArea,
		ospfv3VirtNbrRtrId }
	-- 1.3.6.1.2.1.191.1.11.1
	::= { ospfv3VirtNbrTable 1 }


Ospfv3VirtNbrEntry ::= SEQUENCE {

	ospfv3VirtNbrArea                    Ospfv3AreaIdTC,
	ospfv3VirtNbrRtrId                   Ospfv3RouterIdTC,
	ospfv3VirtNbrIfIndex                 InterfaceIndex,
	ospfv3VirtNbrIfInstId                Ospfv3IfInstIdTC,
	ospfv3VirtNbrAddressType             InetAddressType,
	ospfv3VirtNbrAddress                 InetAddress,
	ospfv3VirtNbrOptions                 Integer32,
	ospfv3VirtNbrState                   INTEGER,
	ospfv3VirtNbrEvents                  Counter32,
	ospfv3VirtNbrLsRetransQLen           Gauge32,
	ospfv3VirtNbrHelloSuppressed         TruthValue,
	ospfv3VirtNbrIfId                    InterfaceIndex,
	ospfv3VirtNbrRestartHelperStatus     INTEGER,
	ospfv3VirtNbrRestartHelperAge        Ospfv3UpToRefreshIntervalTC,
	ospfv3VirtNbrRestartHelperExitReason INTEGER }


ospfv3VirtNbrArea OBJECT-TYPE
	SYNTAX  Ospfv3AreaIdTC
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"The transit area Identifier."
	-- 1.3.6.1.2.1.191.1.11.1.1
	::= { ospfv3VirtNbrEntry 1 }


ospfv3VirtNbrRtrId OBJECT-TYPE
	SYNTAX  Ospfv3RouterIdTC
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"A 32-bit integer uniquely identifying the
		neighboring router in the Autonomous System."
	-- 1.3.6.1.2.1.191.1.11.1.2
	::= { ospfv3VirtNbrEntry 2 }


ospfv3VirtNbrIfIndex OBJECT-TYPE
	SYNTAX  InterfaceIndex
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The local Interface ID for the virtual link over
		which the neighbor can be reached."
	-- 1.3.6.1.2.1.191.1.11.1.3
	::= { ospfv3VirtNbrEntry 3 }


ospfv3VirtNbrIfInstId OBJECT-TYPE
	SYNTAX  Ospfv3IfInstIdTC
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The interface instance for the virtual link over
		which the neighbor can be reached."
	-- 1.3.6.1.2.1.191.1.11.1.4
	::= { ospfv3VirtNbrEntry 4 }


ospfv3VirtNbrAddressType OBJECT-TYPE
	SYNTAX  InetAddressType
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The address type of ospfv3VirtNbrAddress.  Only IPv6
		addresses without zone index are expected."
	-- 1.3.6.1.2.1.191.1.11.1.5
	::= { ospfv3VirtNbrEntry 5 }


ospfv3VirtNbrAddress OBJECT-TYPE
	SYNTAX  InetAddress
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The IPv6 address advertised by this virtual neighbor.
		It must be a global scope address."
	-- 1.3.6.1.2.1.191.1.11.1.6
	::= { ospfv3VirtNbrEntry 6 }


ospfv3VirtNbrOptions OBJECT-TYPE
	SYNTAX  Integer32
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"A bit mask corresponding to the neighbor's options
		field."
	REFERENCE
		"OSPF for IPv6, Appendix A.2, The Options Field"
	-- 1.3.6.1.2.1.191.1.11.1.7
	::= { ospfv3VirtNbrEntry 7 }


ospfv3VirtNbrState OBJECT-TYPE
	SYNTAX  INTEGER {
			down(1),
			attempt(2),
			init(3),
			twoWay(4),
			exchangeStart(5),
			exchange(6),
			loading(7),
			full(8) }
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The state of the virtual neighbor relationship."
	-- 1.3.6.1.2.1.191.1.11.1.8
	::= { ospfv3VirtNbrEntry 8 }


ospfv3VirtNbrEvents OBJECT-TYPE
	SYNTAX  Counter32
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The number of times this virtual link has
		changed its state or an error has occurred.

		Discontinuities in the value of this counter
		can occur at re-initialization of the management
		system and at other times as indicated by the
		value of ospfv3DiscontinuityTime."
	-- 1.3.6.1.2.1.191.1.11.1.9
	::= { ospfv3VirtNbrEntry 9 }


ospfv3VirtNbrLsRetransQLen OBJECT-TYPE
	SYNTAX  Gauge32
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The current length of the retransmission
		queue."
	-- 1.3.6.1.2.1.191.1.11.1.10
	::= { ospfv3VirtNbrEntry 10 }


ospfv3VirtNbrHelloSuppressed OBJECT-TYPE
	SYNTAX  TruthValue
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Indicates whether Hellos are being suppressed
		to the neighbor."
	-- 1.3.6.1.2.1.191.1.11.1.11
	::= { ospfv3VirtNbrEntry 11 }


ospfv3VirtNbrIfId OBJECT-TYPE
	SYNTAX  InterfaceIndex
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The Interface ID that the neighbor advertises
		in its Hello packets on this virtual link, that is,
		the neighbor's local Interface ID."
	-- 1.3.6.1.2.1.191.1.11.1.12
	::= { ospfv3VirtNbrEntry 12 }


ospfv3VirtNbrRestartHelperStatus OBJECT-TYPE
	SYNTAX  INTEGER {
			notHelping(1),
			helping(2) }
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Indicates whether the router is acting
		as a graceful restart helper for the neighbor."
	-- 1.3.6.1.2.1.191.1.11.1.13
	::= { ospfv3VirtNbrEntry 13 }


ospfv3VirtNbrRestartHelperAge OBJECT-TYPE
	SYNTAX  Ospfv3UpToRefreshIntervalTC
	UNITS	"seconds"
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Remaining time in the current OSPF graceful restart
		interval, if the router is acting as a restart
		helper for the neighbor."
	-- 1.3.6.1.2.1.191.1.11.1.14
	::= { ospfv3VirtNbrEntry 14 }


ospfv3VirtNbrRestartHelperExitReason OBJECT-TYPE
	SYNTAX  INTEGER {
			none(1),
			inProgress(2),
			completed(3),
			timedOut(4),
			topologyChanged(5) }
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Describes the outcome of the last attempt at acting
		as a graceful restart helper for the neighbor.

		none:            no restart has yet been attempted.
		inProgress:      a restart attempt is currently underway.
		completed:       the last restart completed successfully.
		timedOut:        the last restart timed out.
		topologyChanged: the last restart was aborted due to
		                 a topology change."
	-- 1.3.6.1.2.1.191.1.11.1.15
	::= { ospfv3VirtNbrEntry 15 }


--
-- The OSPFv3 Area Aggregate Table
--

ospfv3AreaAggregateTable OBJECT-TYPE
	SYNTAX  SEQUENCE OF Ospfv3AreaAggregateEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"The Area Aggregate Table acts as an adjunct
		to the Area Table.  It describes those address
		aggregates that are configured to be propagated
		from an area.  Its purpose is to reduce the amount
		of information that is known beyond an area's
		borders.

		A range of IPv6 prefixes specified by a
		prefix / prefix length pair.  Note that if
		ranges are configured such that one range
		subsumes another range, the most specific
		match is the preferred one."
	-- 1.3.6.1.2.1.191.1.12
	::= { ospfv3Objects 12 }


ospfv3AreaAggregateEntry OBJECT-TYPE
	SYNTAX  Ospfv3AreaAggregateEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"A single area aggregate entry.

		Information in this table is persistent, and
		when this object is written, the entity SHOULD
		save the change to non-volatile storage."
	REFERENCE
		"OSPF Version 2, Appendix C.2, Area parameters"
	INDEX {
		ospfv3AreaAggregateAreaID,
		ospfv3AreaAggregateAreaLsdbType,
		ospfv3AreaAggregatePrefixType,
		ospfv3AreaAggregatePrefix,
		ospfv3AreaAggregatePrefixLength }
	-- 1.3.6.1.2.1.191.1.12.1
	::= { ospfv3AreaAggregateTable 1 }


Ospfv3AreaAggregateEntry ::= SEQUENCE {

	ospfv3AreaAggregateAreaID       Ospfv3AreaIdTC,
	ospfv3AreaAggregateAreaLsdbType INTEGER,
	ospfv3AreaAggregatePrefixType   InetAddressType,
	ospfv3AreaAggregatePrefix       InetAddress,
	ospfv3AreaAggregatePrefixLength InetAddressPrefixLength,
	ospfv3AreaAggregateRowStatus    RowStatus,
	ospfv3AreaAggregateEffect       INTEGER,
	ospfv3AreaAggregateRouteTag     Unsigned32 }


ospfv3AreaAggregateAreaID OBJECT-TYPE
	SYNTAX  Ospfv3AreaIdTC
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"The area the Address Aggregate is to be found
		within."
	REFERENCE
		"OSPF Version 2, Appendix C.2, Area parameters"
	-- 1.3.6.1.2.1.191.1.12.1.1
	::= { ospfv3AreaAggregateEntry 1 }


ospfv3AreaAggregateAreaLsdbType OBJECT-TYPE
	SYNTAX  INTEGER {
			interAreaPrefixLsa(8195), 	-- 0x2003
			nssaExternalLsa(8199)    	-- 0x2007
			}
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"The type of the Address Aggregate.  This field
		specifies the Area LSDB type that this Address
		Aggregate applies to."
	REFERENCE
		"OSPF Version 2, Appendix A.4.1, The LSA header"
	-- 1.3.6.1.2.1.191.1.12.1.2
	::= { ospfv3AreaAggregateEntry 2 }


ospfv3AreaAggregatePrefixType OBJECT-TYPE
	SYNTAX  InetAddressType
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"The prefix type of ospfv3AreaAggregatePrefix.  Only
		IPv6 addresses are expected."
	-- 1.3.6.1.2.1.191.1.12.1.3
	::= { ospfv3AreaAggregateEntry 3 }


ospfv3AreaAggregatePrefix OBJECT-TYPE
	SYNTAX  InetAddress (SIZE (0..16))
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"The IPv6 prefix."
	REFERENCE
		"OSPF Version 2, Appendix C.2, Area parameters"
	-- 1.3.6.1.2.1.191.1.12.1.4
	::= { ospfv3AreaAggregateEntry 4 }


ospfv3AreaAggregatePrefixLength OBJECT-TYPE
	SYNTAX  InetAddressPrefixLength (3..128)
	UNITS	"bits"
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"The length of the prefix (in bits).  A prefix can
		not be shorter than 3 bits."
	REFERENCE
		"OSPF Version 2, Appendix C.2, Area parameters"
	-- 1.3.6.1.2.1.191.1.12.1.5
	::= { ospfv3AreaAggregateEntry 5 }


ospfv3AreaAggregateRowStatus OBJECT-TYPE
	SYNTAX  RowStatus
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"This object permits management of the table by
		facilitating actions such as row creation,
		construction, and destruction.

		The value of this object has no effect on
		whether other objects in this conceptual row can be
		modified."
	-- 1.3.6.1.2.1.191.1.12.1.6
	::= { ospfv3AreaAggregateEntry 6 }


ospfv3AreaAggregateEffect OBJECT-TYPE
	SYNTAX  INTEGER {
			advertiseMatching(1),
			doNotAdvertiseMatching(2) }
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"Prefixes subsumed by ranges will either trigger the
		advertisement of the indicated aggregate
		(advertiseMatching) or result in the prefix not
		being advertised at all outside the area."
	DEFVAL { advertiseMatching }
	-- 1.3.6.1.2.1.191.1.12.1.7
	::= { ospfv3AreaAggregateEntry 7 }


ospfv3AreaAggregateRouteTag OBJECT-TYPE
	SYNTAX  Unsigned32
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"This tag is advertised only in the summarized
		As-External LSA when summarizing from NSSA-LSAs to
		AS-External-LSAs."
	DEFVAL { 0 }
	-- 1.3.6.1.2.1.191.1.12.1.8
	::= { ospfv3AreaAggregateEntry 8 }


-- OSPFv3 Link-Scope Link State Database, for virtual interfaces

ospfv3VirtLinkLsdbTable OBJECT-TYPE
	SYNTAX  SEQUENCE OF Ospfv3VirtLinkLsdbEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"The OSPFv3 Process's Link-scope LSDB for virtual
		interfaces.  The LSDB contains the Link-scope link
		state advertisements from virtual interfaces."
	-- 1.3.6.1.2.1.191.1.13
	::= { ospfv3Objects 13 }


ospfv3VirtLinkLsdbEntry OBJECT-TYPE
	SYNTAX  Ospfv3VirtLinkLsdbEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"A single Link-scope link state advertisement
		for a virtual interface."
	INDEX {
		ospfv3VirtLinkLsdbIfAreaId,
		ospfv3VirtLinkLsdbIfNeighbor,
		ospfv3VirtLinkLsdbType,
		ospfv3VirtLinkLsdbRouterId,
		ospfv3VirtLinkLsdbLsid }
	-- 1.3.6.1.2.1.191.1.13.1
	::= { ospfv3VirtLinkLsdbTable 1 }


Ospfv3VirtLinkLsdbEntry ::= SEQUENCE {

	ospfv3VirtLinkLsdbIfAreaId      Ospfv3AreaIdTC,
	ospfv3VirtLinkLsdbIfNeighbor    Ospfv3RouterIdTC,
	ospfv3VirtLinkLsdbType          Unsigned32,
	ospfv3VirtLinkLsdbRouterId      Ospfv3RouterIdTC,
	ospfv3VirtLinkLsdbLsid          Ospfv3LsIdTC,
	ospfv3VirtLinkLsdbSequence      Ospfv3LsaSequenceTC,
	ospfv3VirtLinkLsdbAge           Ospfv3LsaAgeTC,
	ospfv3VirtLinkLsdbChecksum      Integer32,
	ospfv3VirtLinkLsdbAdvertisement OCTET STRING,
	ospfv3VirtLinkLsdbTypeKnown     TruthValue }


ospfv3VirtLinkLsdbIfAreaId OBJECT-TYPE
	SYNTAX  Ospfv3AreaIdTC
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"The transit area that the virtual link
		traverses.  By definition, this is not
		Area 0."
	-- 1.3.6.1.2.1.191.1.13.1.1
	::= { ospfv3VirtLinkLsdbEntry 1 }


ospfv3VirtLinkLsdbIfNeighbor OBJECT-TYPE
	SYNTAX  Ospfv3RouterIdTC
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"The Router ID of the virtual neighbor."
	-- 1.3.6.1.2.1.191.1.13.1.2
	::= { ospfv3VirtLinkLsdbEntry 2 }


ospfv3VirtLinkLsdbType OBJECT-TYPE
	SYNTAX  Unsigned32 (0..4294967295)
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"The type of the link state advertisement.
		Each link state type has a separate
		advertisement format.  Link-scope LSAs unrecognized
		by the router are also stored in this database."
	-- 1.3.6.1.2.1.191.1.13.1.3
	::= { ospfv3VirtLinkLsdbEntry 3 }


ospfv3VirtLinkLsdbRouterId OBJECT-TYPE
	SYNTAX  Ospfv3RouterIdTC
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"The 32-bit number that uniquely identifies the
		originating router in the Autonomous System."
	REFERENCE
		"OSPF Version 2, Appendix C.1, Global parameters"
	-- 1.3.6.1.2.1.191.1.13.1.4
	::= { ospfv3VirtLinkLsdbEntry 4 }


ospfv3VirtLinkLsdbLsid OBJECT-TYPE
	SYNTAX  Ospfv3LsIdTC
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"The Link State ID is an LS type-specific field
		containing a unique identifier;
		it identifies the piece of the routing domain
		that is being described by the advertisement.
		In contrast to OSPFv2, the LSID has no
		addressing semantics."
	-- 1.3.6.1.2.1.191.1.13.1.5
	::= { ospfv3VirtLinkLsdbEntry 5 }


-- Note that the OSPF sequence number is a 32-bit signed
-- integer.  It starts with the value '80000001'h
-- or -'7FFFFFFF'h, and increments until '7FFFFFFF'h.
-- Thus, a typical sequence number will be very negative.

ospfv3VirtLinkLsdbSequence OBJECT-TYPE
	SYNTAX  Ospfv3LsaSequenceTC
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The sequence number field is a signed 32-bit
		integer.  It is used to detect old and duplicate
		link state advertisements.  The space of
		sequence numbers is linearly ordered.  The
		larger the sequence number, the more recent the
		advertisement."
	REFERENCE
		"OSPF Version 2, Section 12.1.6, LS sequence
		number"
	-- 1.3.6.1.2.1.191.1.13.1.6
	::= { ospfv3VirtLinkLsdbEntry 6 }


ospfv3VirtLinkLsdbAge OBJECT-TYPE
	SYNTAX  Ospfv3LsaAgeTC
	UNITS	"seconds"
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"This field is the age of the link state
		advertisement in seconds.  The high-order bit
		of the LS age field is considered the DoNotAge
		bit for support of on-demand circuits."
	REFERENCE
		"OSPF Version 2, Section 12.1.1, LS age;
		Extending OSPF to Support Demand Circuits,
		Section 2.2, The LS age field."
	-- 1.3.6.1.2.1.191.1.13.1.7
	::= { ospfv3VirtLinkLsdbEntry 7 }


ospfv3VirtLinkLsdbChecksum OBJECT-TYPE
	SYNTAX  Integer32
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"This field is the checksum of the complete
		contents of the advertisement, excepting the
		age field.  The age field is excepted so that
		an advertisement's age can be incremented
		without updating the checksum.  The checksum
		used is the same that is used for ISO
		connectionless datagrams; it is commonly
		referred to as the Fletcher checksum."
	REFERENCE
		"OSPF Version 2, Section 12.1.7, LS checksum"
	-- 1.3.6.1.2.1.191.1.13.1.8
	::= { ospfv3VirtLinkLsdbEntry 8 }


ospfv3VirtLinkLsdbAdvertisement OBJECT-TYPE
	SYNTAX  OCTET STRING (SIZE (1..65535))
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The entire link state advertisement, including
		its header."
	-- 1.3.6.1.2.1.191.1.13.1.9
	::= { ospfv3VirtLinkLsdbEntry 9 }


ospfv3VirtLinkLsdbTypeKnown OBJECT-TYPE
	SYNTAX  TruthValue
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The value true (1) indicates that the LSA type is
		recognized by this router."
	-- 1.3.6.1.2.1.191.1.13.1.10
	::= { ospfv3VirtLinkLsdbEntry 10 }


-- The Ospfv3 Notification Table
-- The Ospfv3 Notification Table records fields that are
-- required for notifications.

ospfv3NotificationEntry OBJECT IDENTIFIER 
	-- 1.3.6.1.2.1.191.1.14
	::= { ospfv3Objects 14 }

ospfv3ConfigErrorType OBJECT-TYPE
	SYNTAX  INTEGER {
			badVersion(1),
			areaMismatch(2),
			unknownNbmaNbr(3),        	-- Router is DR eligible
			unknownVirtualNbr(4),
			helloIntervalMismatch(5),
			deadIntervalMismatch(6),
			optionMismatch(7),
			mtuMismatch(8),
			duplicateRouterId(9),
			noError(10) }
	MAX-ACCESS accessible-for-notify
	STATUS  current
	DESCRIPTION
		"Potential types of configuration conflicts.
		Used by the ospfv3ConfigError and
		ospfv3ConfigVirtError notifications."
	-- 1.3.6.1.2.1.191.1.14.1
	::= { ospfv3NotificationEntry 1 }


ospfv3PacketType OBJECT-TYPE
	SYNTAX  INTEGER {
			hello(1),
			dbDescript(2),
			lsReq(3),
			lsUpdate(4),
			lsAck(5),
			nullPacket(6) }
	MAX-ACCESS accessible-for-notify
	STATUS  current
	DESCRIPTION
		"OSPFv3 packet types."
	-- 1.3.6.1.2.1.191.1.14.2
	::= { ospfv3NotificationEntry 2 }


ospfv3PacketSrc OBJECT-TYPE
	SYNTAX  InetAddressIPv6
	MAX-ACCESS accessible-for-notify
	STATUS  current
	DESCRIPTION
		"The IPv6 address of an inbound packet that cannot
		be identified by a neighbor instance.

		Only IPv6 addresses without zone index are expected."
	-- 1.3.6.1.2.1.191.1.14.3
	::= { ospfv3NotificationEntry 3 }



-- Notification Definitions
-- The notifications need to be throttled so as to not overwhelm the
-- management agent in case of rapid changes to the OSPFv3 module.

ospfv3VirtIfStateChange NOTIFICATION-TYPE
	OBJECTS {
		ospfv3RouterId,
		ospfv3VirtIfState}
	STATUS  current
	DESCRIPTION
		"An ospfv3VirtIfStateChange notification signifies that
		there has been a change in the state of an OSPFv3 virtual
		interface.

		This notification should be generated when the interface
		state regresses (e.g., goes from Point-to-Point to Down)
		or progresses to a terminal state (i.e., Point-to-Point)."
	-- 1.3.6.1.2.1.191.0.1
	::= { ospfv3Notifications 1 }


ospfv3NbrStateChange NOTIFICATION-TYPE
	OBJECTS {
		ospfv3RouterId,
		ospfv3NbrState}
	STATUS  current
	DESCRIPTION
		"An ospfv3NbrStateChange notification signifies that
		there has been a change in the state of a
		non-virtual OSPFv3 neighbor.  This notification should be
		generated when the neighbor state regresses
		(e.g., goes from Attempt or Full to 1-Way or
		Down) or progresses to a terminal state (e.g.,
		2-Way or Full).  When a neighbor transitions
		from or to Full on non-broadcast multi-access
		and broadcast networks, the notification should be
		generated by the Designated Router.  A Designated
		Router transitioning to Down will be noted by
		ospfIfStateChange."
	-- 1.3.6.1.2.1.191.0.2
	::= { ospfv3Notifications 2 }


ospfv3VirtNbrStateChange NOTIFICATION-TYPE
	OBJECTS {
		ospfv3RouterId,
		ospfv3VirtNbrState}
	STATUS  current
	DESCRIPTION
		"An ospfv3VirtNbrStateChange notification signifies
		that there has been a change in the state of an OSPFv3
		virtual neighbor.  This notification should be generated
		when the neighbor state regresses (e.g., goes
		from Attempt or Full to 1-Way or Down) or
		progresses to a terminal state (e.g., Full)."
	-- 1.3.6.1.2.1.191.0.3
	::= { ospfv3Notifications 3 }


ospfv3IfConfigError NOTIFICATION-TYPE
	OBJECTS {
		ospfv3RouterId,
		ospfv3IfState,
		ospfv3PacketSrc,
		ospfv3ConfigErrorType,
		ospfv3PacketType}
	STATUS  current
	DESCRIPTION
		"An ospfv3IfConfigError notification signifies that a
		packet has been received on a non-virtual
		interface from a router whose configuration
		parameters conflict with this router's
		configuration parameters.  Note that the event
		optionMismatch should cause a notification only if it
		prevents an adjacency from forming."
	-- 1.3.6.1.2.1.191.0.4
	::= { ospfv3Notifications 4 }


ospfv3VirtIfConfigError NOTIFICATION-TYPE
	OBJECTS {
		ospfv3RouterId,
		ospfv3VirtIfState,
		ospfv3ConfigErrorType,
		ospfv3PacketType}
	STATUS  current
	DESCRIPTION
		"An ospfv3VirtIfConfigError notification signifies that a
		packet has been received on a virtual interface
		from a router whose configuration parameters
		conflict with this router's configuration
		parameters.  Note that the event optionMismatch
		should cause a notification only if it prevents an
		adjacency from forming."
	-- 1.3.6.1.2.1.191.0.5
	::= { ospfv3Notifications 5 }


ospfv3IfRxBadPacket NOTIFICATION-TYPE
	OBJECTS {
		ospfv3RouterId,
		ospfv3IfState,
		ospfv3PacketSrc,
		ospfv3PacketType}
	STATUS  current
	DESCRIPTION
		"An ospfv3IfRxBadPacket notification signifies that an
		OSPFv3 packet that cannot be parsed has been received on a
		non-virtual interface."
	-- 1.3.6.1.2.1.191.0.6
	::= { ospfv3Notifications 6 }


ospfv3VirtIfRxBadPacket NOTIFICATION-TYPE
	OBJECTS {
		ospfv3RouterId,
		ospfv3VirtIfState,
		ospfv3PacketType}
	STATUS  current
	DESCRIPTION
		"An ospfv3VirtIfRxBadPacket notification signifies
		that an OSPFv3 packet that cannot be parsed has been
		received on a virtual interface."
	-- 1.3.6.1.2.1.191.0.7
	::= { ospfv3Notifications 7 }


ospfv3LsdbOverflow NOTIFICATION-TYPE
	OBJECTS {
		ospfv3RouterId,
		ospfv3ExtAreaLsdbLimit}
	STATUS  current
	DESCRIPTION
		"An ospfv3LsdbOverflow notification signifies that the
		number of LSAs in the router's link state
		database has exceeded ospfv3ExtAreaLsdbLimit."
	-- 1.3.6.1.2.1.191.0.8
	::= { ospfv3Notifications 8 }


ospfv3LsdbApproachingOverflow NOTIFICATION-TYPE
	OBJECTS {
		ospfv3RouterId,
		ospfv3ExtAreaLsdbLimit}
	STATUS  current
	DESCRIPTION
		"An ospfv3LsdbApproachingOverflow notification signifies
		that the number of LSAs in the router's
		link state database has exceeded ninety percent of
		ospfv3ExtAreaLsdbLimit."
	-- 1.3.6.1.2.1.191.0.9
	::= { ospfv3Notifications 9 }


ospfv3IfStateChange NOTIFICATION-TYPE
	OBJECTS {
		ospfv3RouterId,
		ospfv3IfState}
	STATUS  current
	DESCRIPTION
		"An ospfv3IfStateChange notification signifies that there
		has been a change in the state of a non-virtual
		OSPFv3 interface.  This notification should be generated
		when the interface state regresses (e.g., goes
		from DR to Down) or progresses to a terminal
		state (i.e., Point-to-Point, DR Other, DR, or
		Backup)."
	-- 1.3.6.1.2.1.191.0.10
	::= { ospfv3Notifications 10 }


ospfv3NssaTranslatorStatusChange NOTIFICATION-TYPE
	OBJECTS {
		ospfv3RouterId,
		ospfv3AreaNssaTranslatorState}
	STATUS  current
	DESCRIPTION
		"An ospfv3NssaTranslatorStatusChange notification
		indicates that there has been a change in the router's
		ability to translate OSPFv3 NSSA LSAs into OSPFv3 External
		LSAs.  This notification should be generated when the
		Translator Status transitions from or to any defined
		status on a per-area basis."
	-- 1.3.6.1.2.1.191.0.11
	::= { ospfv3Notifications 11 }


ospfv3RestartStatusChange NOTIFICATION-TYPE
	OBJECTS {
		ospfv3RouterId,
		ospfv3RestartStatus,
		ospfv3RestartInterval,
		ospfv3RestartExitReason}
	STATUS  current
	DESCRIPTION
		"An ospfv3RestartStatusChange notification signifies that
		there has been a change in the graceful restart
		state for the router.  This notification should be
		generated when the router restart status
		changes."
	-- 1.3.6.1.2.1.191.0.12
	::= { ospfv3Notifications 12 }


ospfv3NbrRestartHelperStatusChange NOTIFICATION-TYPE
	OBJECTS {
		ospfv3RouterId,
		ospfv3NbrRestartHelperStatus,
		ospfv3NbrRestartHelperAge,
		ospfv3NbrRestartHelperExitReason}
	STATUS  current
	DESCRIPTION
		"An ospfv3NbrRestartHelperStatusChange notification
		signifies that there has been a change in the
		graceful restart helper state for the neighbor.
		This notification should be generated when the
		neighbor restart helper status transitions for a neighbor."
	-- 1.3.6.1.2.1.191.0.13
	::= { ospfv3Notifications 13 }


ospfv3VirtNbrRestartHelperStatusChange NOTIFICATION-TYPE
	OBJECTS {
		ospfv3RouterId,
		ospfv3VirtNbrRestartHelperStatus,
		ospfv3VirtNbrRestartHelperAge,
		ospfv3VirtNbrRestartHelperExitReason}
	STATUS  current
	DESCRIPTION
		"An ospfv3VirtNbrRestartHelperStatusChange
		notification signifies that there has been a
		change in the graceful restart helper state for
		the virtual neighbor.  This notification should be
		generated when the virtual neighbor restart helper status
		transitions for a virtual neighbor."
	-- 1.3.6.1.2.1.191.0.14
	::= { ospfv3Notifications 14 }

-- Conformance Information

ospfv3Groups OBJECT IDENTIFIER 
	-- 1.3.6.1.2.1.191.2.1
	::= { ospfv3Conformance 1 }

ospfv3Compliances OBJECT IDENTIFIER 
	-- 1.3.6.1.2.1.191.2.2
	::= { ospfv3Conformance 2 }


-- Compliance Statements

ospfv3FullCompliance MODULE-COMPLIANCE
	STATUS  current
	DESCRIPTION
		"The compliance statement"

	MODULE 
	MANDATORY-GROUPS {
			ospfv3BasicGroup,
			ospfv3AreaGroup,
			ospfv3IfGroup,
			ospfv3VirtIfGroup,
			ospfv3NbrGroup,
			ospfv3CfgNbrGroup,
			ospfv3VirtNbrGroup,
			ospfv3AreaAggregateGroup }

	GROUP ospfv3AsLsdbGroup
	  DESCRIPTION
		"This group is required for OSPFv3 systems that
		display their AS-scope link state database."
	GROUP ospfv3AreaLsdbGroup
	  DESCRIPTION
		"This group is required for OSPFv3 systems that
		display their Area-scope link state database."
	GROUP ospfv3LinkLsdbGroup
	  DESCRIPTION
		"This group is required for OSPFv3 systems that
		display their Link-scope link state database
		for non-virtual interfaces."
	GROUP ospfv3VirtLinkLsdbGroup
	  DESCRIPTION
		"This group is required for OSPFv3 systems that
		display their Link-scope link state database
		for virtual interfaces."
	GROUP ospfv3HostGroup
	  DESCRIPTION
		"This group is required for OSPFv3 systems that
		support attached hosts."
	GROUP ospfv3NotificationObjectGroup
	  DESCRIPTION
		"This group is required for OSPFv3 systems that
		support OSPFv3 notifications."
	GROUP ospfv3NotificationGroup
	  DESCRIPTION
		"This group is required for OSPFv3 systems that
		support OSPFv3 notifications."
	OBJECT ospfv3NbrAddressType
	  SYNTAX InetAddressType {
			ipv6(2) }
	  DESCRIPTION 
		"An implementation is only required to support IPv6
		address without zone index."
	OBJECT ospfv3NbrAddress
	  SYNTAX InetAddress (SIZE (16))
	  DESCRIPTION 
		"An implementation is only required to support IPv6
		address without zone index."
	OBJECT ospfv3VirtNbrAddressType
	  SYNTAX InetAddressType {
			ipv6(2) }
	  DESCRIPTION 
		"An implementation is only required to support IPv6
		address without zone index."
	OBJECT ospfv3VirtNbrAddress
	  SYNTAX InetAddress (SIZE (16))
	  DESCRIPTION 
		"An implementation is only required to support IPv6
		address without zone index."
	-- 1.3.6.1.2.1.191.2.2.1
	::= { ospfv3Compliances 1 }


ospfv3ReadOnlyCompliance MODULE-COMPLIANCE
	STATUS  current
	DESCRIPTION
		"When this MIB module is implemented without
		support for read-create (i.e., in read-only
		mode), the implementation can claim read-only
		compliance.  Such a device can then be monitored,
		but cannot be configured with this MIB."

	MODULE 
	MANDATORY-GROUPS {
			ospfv3BasicGroup,
			ospfv3AreaGroup,
			ospfv3IfGroup,
			ospfv3VirtIfGroup,
			ospfv3NbrGroup,
			ospfv3CfgNbrGroup,
			ospfv3VirtNbrGroup,
			ospfv3AreaAggregateGroup }

	GROUP ospfv3AsLsdbGroup
	  DESCRIPTION
		"This group is required for OSPFv3 systems that
		display their AS-scope link state database."
	GROUP ospfv3AreaLsdbGroup
	  DESCRIPTION
		"This group is required for OSPFv3 systems that
		display their Area-scope link state database."
	GROUP ospfv3LinkLsdbGroup
	  DESCRIPTION
		"This group is required for OSPFv3 systems that
		display their Link-scope link state database
		for non-virtual interfaces."
	GROUP ospfv3VirtLinkLsdbGroup
	  DESCRIPTION
		"This group is required for OSPFv3 systems that
		display their Link-scope link state database
		for virtual interfaces."
	GROUP ospfv3HostGroup
	  DESCRIPTION
		"This group is required for OSPFv3 systems that
		support attached hosts."
	GROUP ospfv3NotificationObjectGroup
	  DESCRIPTION
		"This group is required for OSPFv3 systems that
		support OSPFv3 notifications."
	GROUP ospfv3NotificationGroup
	  DESCRIPTION
		"This group is required for OSPFv3 systems that
		support OSPFv3 notifications."
	OBJECT ospfv3RouterId
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT ospfv3AdminStatus
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT ospfv3ExtAreaLsdbLimit
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT ospfv3ExitOverflowInterval
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT ospfv3DemandExtensions
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT ospfv3ReferenceBandwidth
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT ospfv3RestartSupport
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT ospfv3RestartInterval
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT ospfv3RestartStrictLsaChecking
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT ospfv3NotificationEnable
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT ospfv3StubRouterAdvertisement
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT ospfv3AreaImportAsExtern
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT ospfv3AreaSummary
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT ospfv3AreaRowStatus
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT ospfv3AreaStubMetric
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT ospfv3AreaNssaTranslatorRole
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT ospfv3AreaNssaTranslatorStabInterval
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT ospfv3AreaStubMetricType
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT ospfv3AreaTEEnabled
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT ospfv3HostMetric
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT ospfv3HostRowStatus
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT ospfv3HostAreaID
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT ospfv3IfAreaId
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT ospfv3IfType
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT ospfv3IfAdminStatus
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT ospfv3IfRtrPriority
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT ospfv3IfTransitDelay
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT ospfv3IfRetransInterval
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT ospfv3IfHelloInterval
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT ospfv3IfRtrDeadInterval
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT ospfv3IfPollInterval
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT ospfv3IfRowStatus
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT ospfv3IfDemand
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT ospfv3IfMetricValue
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT ospfv3IfDemandNbrProbe
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT ospfv3IfDemandNbrProbeRetransLimit
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT ospfv3IfDemandNbrProbeInterval
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT ospfv3IfTEDisabled
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT ospfv3IfLinkLSASuppression
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT ospfv3VirtIfTransitDelay
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT ospfv3VirtIfRetransInterval
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT ospfv3VirtIfHelloInterval
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT ospfv3VirtIfRtrDeadInterval
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT ospfv3VirtIfRowStatus
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT ospfv3CfgNbrPriority
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT ospfv3CfgNbrRowStatus
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT ospfv3AreaAggregateRowStatus
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT ospfv3AreaAggregateEffect
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	OBJECT ospfv3AreaAggregateRouteTag
	  MIN-ACCESS read-only
	  DESCRIPTION 
		"Write access is not required."
	-- 1.3.6.1.2.1.191.2.2.2
	::= { ospfv3Compliances 2 }

-- units of conformance

ospfv3BasicGroup OBJECT-GROUP
	OBJECTS {
		ospfv3RouterId,
		ospfv3AdminStatus,
		ospfv3VersionNumber,
		ospfv3AreaBdrRtrStatus,
		ospfv3ASBdrRtrStatus,
		ospfv3AsScopeLsaCount,
		ospfv3AsScopeLsaCksumSum,
		ospfv3OriginateNewLsas,
		ospfv3RxNewLsas,
		ospfv3ExtLsaCount,
		ospfv3ExtAreaLsdbLimit,
		ospfv3ExitOverflowInterval,
		ospfv3DemandExtensions,
		ospfv3ReferenceBandwidth,
		ospfv3RestartSupport,
		ospfv3RestartInterval,
		ospfv3RestartStrictLsaChecking,
		ospfv3RestartStatus,
		ospfv3RestartAge,
		ospfv3RestartExitReason,
		ospfv3NotificationEnable,
		ospfv3StubRouterSupport,
		ospfv3StubRouterAdvertisement,
		ospfv3DiscontinuityTime,
		ospfv3RestartTime }
	STATUS  current
	DESCRIPTION
		"These objects are used for managing/monitoring
		OSPFv3 global parameters."
	-- 1.3.6.1.2.1.191.2.1.1
	::= { ospfv3Groups 1 }

ospfv3AreaGroup OBJECT-GROUP
	OBJECTS {
		ospfv3AreaImportAsExtern,
		ospfv3AreaSpfRuns,
		ospfv3AreaBdrRtrCount,
		ospfv3AreaAsBdrRtrCount,
		ospfv3AreaScopeLsaCount,
		ospfv3AreaScopeLsaCksumSum,
		ospfv3AreaSummary,
		ospfv3AreaRowStatus,
		ospfv3AreaStubMetric,
		ospfv3AreaNssaTranslatorRole,
		ospfv3AreaNssaTranslatorState,
		ospfv3AreaNssaTranslatorStabInterval,
		ospfv3AreaNssaTranslatorEvents,
		ospfv3AreaStubMetricType,
		ospfv3AreaTEEnabled }
	STATUS  current
	DESCRIPTION
		"These objects are used for OSPFv3 systems
		supporting areas."
	-- 1.3.6.1.2.1.191.2.1.2
	::= { ospfv3Groups 2 }

ospfv3AsLsdbGroup OBJECT-GROUP
	OBJECTS {
		ospfv3AsLsdbSequence,
		ospfv3AsLsdbAge,
		ospfv3AsLsdbChecksum,
		ospfv3AsLsdbAdvertisement,
		ospfv3AsLsdbTypeKnown }
	STATUS  current
	DESCRIPTION
		"These objects are used for OSPFv3 systems
		that display their AS-scope link state database."
	-- 1.3.6.1.2.1.191.2.1.3
	::= { ospfv3Groups 3 }

ospfv3AreaLsdbGroup OBJECT-GROUP
	OBJECTS {
		ospfv3AreaLsdbSequence,
		ospfv3AreaLsdbAge,
		ospfv3AreaLsdbChecksum,
		ospfv3AreaLsdbAdvertisement,
		ospfv3AreaLsdbTypeKnown }
	STATUS  current
	DESCRIPTION
		"These objects are used for OSPFv3 systems
		that display their Area-scope link state database."
	-- 1.3.6.1.2.1.191.2.1.4
	::= { ospfv3Groups 4 }

ospfv3LinkLsdbGroup OBJECT-GROUP
	OBJECTS {
		ospfv3LinkLsdbSequence,
		ospfv3LinkLsdbAge,
		ospfv3LinkLsdbChecksum,
		ospfv3LinkLsdbAdvertisement,
		ospfv3LinkLsdbTypeKnown }
	STATUS  current
	DESCRIPTION
		"These objects are used for OSPFv3 systems
		that display their Link-scope link state database
		for non-virtual interfaces."
	-- 1.3.6.1.2.1.191.2.1.5
	::= { ospfv3Groups 5 }

ospfv3HostGroup OBJECT-GROUP
	OBJECTS {
		ospfv3HostMetric,
		ospfv3HostRowStatus,
		ospfv3HostAreaID }
	STATUS  current
	DESCRIPTION
		"These objects are used for OSPFv3 systems
		that support attached hosts."
	-- 1.3.6.1.2.1.191.2.1.6
	::= { ospfv3Groups 6 }

ospfv3IfGroup OBJECT-GROUP
	OBJECTS {
		ospfv3IfAreaId,
		ospfv3IfType,
		ospfv3IfAdminStatus,
		ospfv3IfRtrPriority,
		ospfv3IfTransitDelay,
		ospfv3IfRetransInterval,
		ospfv3IfHelloInterval,
		ospfv3IfRtrDeadInterval,
		ospfv3IfPollInterval,
		ospfv3IfState,
		ospfv3IfDesignatedRouter,
		ospfv3IfBackupDesignatedRouter,
		ospfv3IfEvents,
		ospfv3IfRowStatus,
		ospfv3IfDemand,
		ospfv3IfMetricValue,
		ospfv3IfLinkScopeLsaCount,
		ospfv3IfLinkLsaCksumSum,
		ospfv3IfDemandNbrProbe,
		ospfv3IfDemandNbrProbeRetransLimit,
		ospfv3IfDemandNbrProbeInterval,
		ospfv3IfTEDisabled,
		ospfv3IfLinkLSASuppression }
	STATUS  current
	DESCRIPTION
		"These interface objects are used for
		managing/monitoring OSPFv3 interfaces."
	-- 1.3.6.1.2.1.191.2.1.7
	::= { ospfv3Groups 7 }

ospfv3VirtIfGroup OBJECT-GROUP
	OBJECTS {
		ospfv3VirtIfIndex,
		ospfv3VirtIfInstId,
		ospfv3VirtIfTransitDelay,
		ospfv3VirtIfRetransInterval,
		ospfv3VirtIfHelloInterval,
		ospfv3VirtIfRtrDeadInterval,
		ospfv3VirtIfState,
		ospfv3VirtIfEvents,
		ospfv3VirtIfRowStatus,
		ospfv3VirtIfLinkScopeLsaCount,
		ospfv3VirtIfLinkLsaCksumSum }
	STATUS  current
	DESCRIPTION
		"These virtual interface objects are used for
		managing/monitoring OSPFv3 virtual interfaces."
	-- 1.3.6.1.2.1.191.2.1.8
	::= { ospfv3Groups 8 }

ospfv3NbrGroup OBJECT-GROUP
	OBJECTS {
		ospfv3NbrAddressType,
		ospfv3NbrAddress,
		ospfv3NbrOptions,
		ospfv3NbrPriority,
		ospfv3NbrState,
		ospfv3NbrEvents,
		ospfv3NbrLsRetransQLen,
		ospfv3NbrHelloSuppressed,
		ospfv3NbrIfId,
		ospfv3NbrRestartHelperStatus,
		ospfv3NbrRestartHelperAge,
		ospfv3NbrRestartHelperExitReason }
	STATUS  current
	DESCRIPTION
		"These neighbor objects are used for
		managing/monitoring OSPFv3 neighbors."
	-- 1.3.6.1.2.1.191.2.1.9
	::= { ospfv3Groups 9 }

ospfv3CfgNbrGroup OBJECT-GROUP
	OBJECTS {
		ospfv3CfgNbrPriority,
		ospfv3CfgNbrRowStatus }
	STATUS  current
	DESCRIPTION
		"These configured neighbor objects are used for
		managing/monitoring OSPFv3-configured neighbors."
	-- 1.3.6.1.2.1.191.2.1.10
	::= { ospfv3Groups 10 }

ospfv3VirtNbrGroup OBJECT-GROUP
	OBJECTS {
		ospfv3VirtNbrIfIndex,
		ospfv3VirtNbrIfInstId,
		ospfv3VirtNbrAddressType,
		ospfv3VirtNbrAddress,
		ospfv3VirtNbrOptions,
		ospfv3VirtNbrState,
		ospfv3VirtNbrEvents,
		ospfv3VirtNbrLsRetransQLen,
		ospfv3VirtNbrHelloSuppressed,
		ospfv3VirtNbrIfId,
		ospfv3VirtNbrRestartHelperStatus,
		ospfv3VirtNbrRestartHelperAge,
		ospfv3VirtNbrRestartHelperExitReason }
	STATUS  current
	DESCRIPTION
		"These virtual neighbor objects are used for
		managing/monitoring OSPFv3 virtual neighbors."
	-- 1.3.6.1.2.1.191.2.1.11
	::= { ospfv3Groups 11 }

ospfv3AreaAggregateGroup OBJECT-GROUP
	OBJECTS {
		ospfv3AreaAggregateRowStatus,
		ospfv3AreaAggregateEffect,
		ospfv3AreaAggregateRouteTag }
	STATUS  current
	DESCRIPTION
		"These area aggregate objects are required for
		aggregating OSPFv3 prefixes for summarization
		across areas."
	-- 1.3.6.1.2.1.191.2.1.12
	::= { ospfv3Groups 12 }

ospfv3VirtLinkLsdbGroup OBJECT-GROUP
	OBJECTS {
		ospfv3VirtLinkLsdbSequence,
		ospfv3VirtLinkLsdbAge,
		ospfv3VirtLinkLsdbChecksum,
		ospfv3VirtLinkLsdbAdvertisement,
		ospfv3VirtLinkLsdbTypeKnown }
	STATUS  current
	DESCRIPTION
		"These objects are used for OSPFv3 systems
		that display their Link-scope link state database
		for virtual interfaces."
	-- 1.3.6.1.2.1.191.2.1.13
	::= { ospfv3Groups 13 }

ospfv3NotificationObjectGroup OBJECT-GROUP
	OBJECTS {
		ospfv3ConfigErrorType,
		ospfv3PacketType,
		ospfv3PacketSrc }
	STATUS  current
	DESCRIPTION
		"These objects are used to record notification
		parameters."
	-- 1.3.6.1.2.1.191.2.1.14
	::= { ospfv3Groups 14 }

ospfv3NotificationGroup NOTIFICATION-GROUP
	NOTIFICATIONS {
		ospfv3VirtIfStateChange,
		ospfv3NbrStateChange,
		ospfv3VirtNbrStateChange,
		ospfv3IfConfigError,
		ospfv3VirtIfConfigError,
		ospfv3IfRxBadPacket,
		ospfv3VirtIfRxBadPacket,
		ospfv3LsdbOverflow,
		ospfv3LsdbApproachingOverflow,
		ospfv3IfStateChange,
		ospfv3NssaTranslatorStatusChange,
		ospfv3RestartStatusChange,
		ospfv3NbrRestartHelperStatusChange,
		ospfv3VirtNbrRestartHelperStatusChange }
	STATUS  current
	DESCRIPTION
		"This group is used for OSPFv3 notifications."
	-- 1.3.6.1.2.1.191.2.1.15
	::= { ospfv3Groups 15 }

END
