G9983-MIB DEFINITIONS ::= BEGIN

IMPORTS
	MODULE-IDENTITY,
	OBJECT-TYPE,
	NOTIFICATION-TYPE,
	mib-2,
	Unsigned32,
	Counter32
		FROM SNMPv2-SMI		-- RFC 2578
	TEXTUAL-CONVENTION,
	RowStatus,
	TruthValue
		FROM SNMPv2-TC		-- RFC 2579
	MODULE-COMPLIANCE,
	OBJECT-GROUP,
	NOTIFICATION-GROUP
		FROM SNMPv2-CONF		-- RFC 2580
	ifIndex,
	InterfaceIndex
		FROM IF-MIB		-- RFC 2863
	HCPerfCurrentCount,
	HCPerfIntervalCount,
	HCPerfValidIntervals,
	HCPerfInvalidIntervals,
	HCPerfTimeElapsed
		FROM HC-PerfHist-TC-MIB		-- RFC 3705
;

------------------------------------------------------------------------
g9983MIB MODULE-IDENTITY
	LAST-UPDATED "201302200000Z"	-- Feb 20, 2013 12:00:00 AM
	ORGANIZATION "IETF ADSL MIB Working Group"
	CONTACT-INFO
		"WG charter:
		  http://datatracker.ietf.org/wg/adslmib/charter/

		Mailing Lists:
		  General Discussion: adslmib@ietf.org
		  To Subscribe: adslmib-request@ietf.org
		  In Body: subscribe your_email_address






		 Chair: Menachem Dodge
		Postal: ECI Telecom, Ltd.
		        30 Hasivim St.
		        Petach-Tikva  4951169
		        Israel
		 Phone: +972-3-926-8421
		 EMail: menachemdodge1@gmail.com

		Editor: Edward Beili
		Postal: Actelis Networks, Inc.
		        25 Bazel St., P.O.B. 10173
		        Petach-Tikva  49103
		        Israel
		 Phone: +972-3-924-3491
		 EMail: edward.beili@actelis.com"
	DESCRIPTION
		"The objects in this MIB module are used to manage the
		 multi-pair bonded xDSL interfaces using time-division inverse
		 multiplexing (TDIM), as defined in ITU-T Recommendation G.998.3
		 (G.Bond/TDIM).

		 This MIB module MUST be used in conjunction with the GBOND-MIB
		 module, common to all G.Bond technologies.

		 The following references are used throughout this MIB module:

		 [G.998.3] refers to:
		   ITU-T Recommendation G.998.3: 'Multi-pair bonding using
		   time-division inverse multiplexing', January 2005.

		 [TR-159] refers to:
		   Broadband Forum Technical Report: 'Management Framework for
		   xDSL Bonding', December 2008.

		 Naming Conventions:
		   BCE    - Bonding Channel Entity
		   BTU    - Bonding Terminating Unit
		   BTU-C  - Bonding Terminating Unit, CO side
		   BTU-R  - Bonding Terminating Unit, Remote Terminal (CPE) side
		   CO     - Central Office
		   CPE    - Customer Premises Equipment
		   GBS    - Generic Bonding Sub-layer
		   GBS-C  - Generic Bonding Sub-layer, CO side
		   GBS-R  - Generic Bonding Sub-layer, Remote Terminal (CPE) side
		   SNR    - Signal to Noise Ratio







		Copyright (c) 2013 IETF Trust and the persons identified as
		authors of the code.  All rights reserved.

		Redistribution and use in source and binary forms, with or without
		modification, is permitted pursuant to, and subject to the license
		terms contained in, the Simplified BSD License set forth in Section
		4.c of the IETF Trust's Legal Provisions Relating to IETF Documents
		(http://trustee.ietf.org/license-info)."
	REVISION "201302200000Z"	-- Feb 20, 2013 12:00:00 AM
	DESCRIPTION
		"Initial version, published as RFC 6766."
	-- 1.3.6.1.2.1.210
	::= { mib-2 210 }


-- Textual Conventions

G9983SvcIndex ::= TEXTUAL-CONVENTION
	DISPLAY-HINT "d"
	STATUS  current
	DESCRIPTION
		"A unique value, greater than zero, for each service defined
		in the managed G.Bond/TDIM port.
		It is RECOMMENDED that values be assigned contiguously
		starting from 1.  The value for each service MUST remain
		constant at least from one re-initialization of the local
		management subsystem to the next re-initialization."
	SYNTAX Unsigned32 (1..255)


G9983SvcIndexList ::= TEXTUAL-CONVENTION
	DISPLAY-HINT "1d:"
	STATUS  current
	DESCRIPTION
		"This textual convention represents a continuous ordered list of
		all the services defined for the managed G.Bond/TDIM port.
		The value of this object is a concatenation of zero or more (up
		to 60) octets, where each octet contains an 8-bit
		G9983SvcIndex value, identifying a particular service.





		An octet's position reflects the associated service position
		and its priority in the G.Bond/TDIM frame, with the first octet
		being the first service of highest priority.

		A zero-length octet string is object-specific and MUST
		therefore be defined as part of the description of any object
		that uses this syntax.  Examples of the usage of a zero-length
		value might include situations where an object using this
		textual convention is irrelevant for a specific G.Bond/TDIM port
		type or where no services have been defined for this port."
	SYNTAX OCTET STRING (SIZE (0..60))


G9983SvcOrderIndex ::= TEXTUAL-CONVENTION
	DISPLAY-HINT "d"
	STATUS  current
	DESCRIPTION
		"A unique value, greater than zero, for each service defined
		in the managed G.Bond/TDIM port, showing its relative position
		inside the G.Bond/TDIM frame."
	SYNTAX Unsigned32 (1..60)


-- Sections of the module
-- Structured as recommended by RFC 4181, Appendix D

g9983Objects OBJECT IDENTIFIER 
	-- 1.3.6.1.2.1.210.1
	::= { g9983MIB 1 }

g9983Conformance OBJECT IDENTIFIER 
	-- 1.3.6.1.2.1.210.2
	::= { g9983MIB 2 }

-- Groups in the module

g9983Port OBJECT IDENTIFIER 
	-- 1.3.6.1.2.1.210.1.1
	::= { g9983Objects 1 }

-- Port Notifications group

g9983PortNotifications OBJECT IDENTIFIER 
	-- 1.3.6.1.2.1.210.1.1.0
	::= { g9983Port 0 }


g9983SvcUp NOTIFICATION-TYPE
	OBJECTS {
		g9983OperSvcIdx,
		g9983SvcIfIdx}
	STATUS  current
	DESCRIPTION
		"This notification indicates that a service, indicated by the
		g9983OperSvcIdx (mapped to a particular interface
		indicated by the g9983SvcIfIdx), in a particular
		G.Bond/TDIM port is passing traffic.

		This notification is generated (unless disabled or dropped by
		the rate-limiting mechanism) when the g9983OperSvcState
		object has left the 'down' state, while the G.Bond/TDIM port
		state (the ifOperStatus of the IF-MIB) is 'up'.

		Generation of this notification is controlled by the
		g9983PortConfSvcUpDownEnable object.

		This object maps to the TR-159 notification nServiceUp."
	REFERENCE
		"[TR-159], Section 5.5.5.7"
	-- 1.3.6.1.2.1.210.1.1.0.1
	::= { g9983PortNotifications 1 }


g9983SvcDown NOTIFICATION-TYPE
	OBJECTS {
		g9983OperSvcIdx,
		g9983SvcIfIdx}
	STATUS  current
	DESCRIPTION
		"This notification indicates that a service indicated by the
		g9983OperSvcIdx (mapped to a particular interface
		indicated by the g9983SvcIfIdx) in a particular
		G.Bond/TDIM port has stopped passing traffic.

		This notification is generated (unless disabled or dropped by
		the rate-limiting mechanism), when the g9983OperSvcState
		object has entered the 'down' state, while the G.Bond/TDIM port
		state (the ifOperStatus of the IF-MIB) is 'up'.

		Generation of this notification is controlled by the
		g9983PortConfSvcUpDownEnable object.

		This object maps to the TR-159 notification nServiceDown."
	REFERENCE
		"[TR-159], Section 5.5.5.8"
	-- 1.3.6.1.2.1.210.1.1.0.2
	::= { g9983PortNotifications 2 }

-- G.Bond/TDIM Port group

g9983PortConfTable OBJECT-TYPE
	SYNTAX  SEQUENCE OF G9983PortConfEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"Table for configuration of G.Bond/TDIM ports.  Entries in
		this table MUST be maintained in a persistent manner."
	-- 1.3.6.1.2.1.210.1.1.1
	::= { g9983Port 1 }


g9983PortConfEntry OBJECT-TYPE
	SYNTAX  G9983PortConfEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"An entry in the G.Bond/TDIM Port Configuration table.
		Each entry represents a G.Bond/TDIM port indexed by the





		ifIndex.  Additional configuration parameters are available
		via the gBondPortConfEntry of the GBOND-MIB.
		Note that a G.Bond/TDIM port runs on top of a single or
		multiple BCE port(s), which are also indexed by the ifIndex."
	INDEX {
		ifIndex }
	-- 1.3.6.1.2.1.210.1.1.1.1
	::= { g9983PortConfTable 1 }


G9983PortConfEntry ::= SEQUENCE {

	g9983PortConfFecAdminState       TruthValue,
	g9983PortConfFecWordSize         Unsigned32,
	g9983PortConfFecRedundancySize   Unsigned32,
	g9983PortConfFecInterleaverType  INTEGER,
	g9983PortConfFecInterleaverDepth Unsigned32,
	g9983PortConfAdminServices       G9983SvcIndexList,
	g9983PortConfSvcUpDownEnable     TruthValue }


g9983PortConfFecAdminState OBJECT-TYPE
	SYNTAX  TruthValue
	MAX-ACCESS read-write
	STATUS  current
	DESCRIPTION
		"A desired state of the OPTIONAL Forward Error Correction
		(FEC) function of the G.Bond/TDIM port.

		A value of 'false' indicates that the FEC function SHALL be
		disabled.  A value of 'true' indicates that the FEC function
		SHALL be enabled, if supported by the G.Bond/TDIM port, as
		indicated by the g9983PortCapFecSupported object.
		The g9983PortStatFecOperState object indicates the current
		operational state of the FEC function.

		For the GBS-R ports, the value of this object cannot be changed
		directly.  This value may be changed as a result of a write
		operation on the g9983PortCapFecSupported object of a remote
		GBS-C.

		Modifications of this object MUST be performed when the link
		is 'down'.
		Attempts to change this object MUST be rejected if the link is
		'up' or initializing, or if it is a GBS-R.

		This object maps to the TR-159/G.998.3 attribute aFECAdminState."
	REFERENCE
		"[TR-159], Section 5.5.4.5; [G.998.3], Appendix II, B-X"
	-- 1.3.6.1.2.1.210.1.1.1.1.1
	::= { g9983PortConfEntry 1 }


g9983PortConfFecWordSize OBJECT-TYPE
	SYNTAX  Unsigned32 (0 | 20..255)
	UNITS	"octets"
	MAX-ACCESS read-write
	STATUS  current
	DESCRIPTION
		"A FEC code word size, in octets, for G.Bond/TDIM ports
		supporting the FEC function.

		This object is read-write for the GBS-C ports and read-only
		for the GBS-R.

		A value of zero SHALL be returned if the FEC function is
		disabled (via g9983PortConfFecAdminState) or not supported.

		Changing of the FEC code word size MUST be performed when the
		FEC-enabled link is 'down'.  Attempts to change this object MUST
		be rejected if the link is 'up' or initializing or if the
		FEC function is disabled/not supported.

		This object maps to the TR-159/G.998.3 attribute aFECWordSize."
	REFERENCE
		"[TR-159], Section 5.5.4.7; [G.998.3], Appendix II, B-XI"
	-- 1.3.6.1.2.1.210.1.1.1.1.2
	::= { g9983PortConfEntry 2 }


g9983PortConfFecRedundancySize OBJECT-TYPE
	SYNTAX  Unsigned32 (0 | 2 | 4 | 8 | 16 | 20)
	UNITS	"octets"
	MAX-ACCESS read-write
	STATUS  current
	DESCRIPTION
		"A FEC redundancy word size, in octets, for G.Bond/TDIM
		ports supporting the FEC function.

		This object is read-write for the GBS-C ports and read-only
		for the GBS-R.

		A value of zero SHALL be returned if the FEC function is
		disabled (via g9983PortConfFecAdminState) or not supported.

		Changing of the FEC redundancy word size MUST be performed
		when the FEC-enabled link is 'down'.  Attempts to change this
		object MUST be rejected if the link is 'up' or initializing or
		if the FEC function is disabled/not supported.

		This object maps to the TR-159/G.998.3 attribute
		aFECRedundancySize."
	REFERENCE
		"[TR-159], Section 5.5.4.8; [G.998.3], Appendix II, B-XII"
	-- 1.3.6.1.2.1.210.1.1.1.1.3
	::= { g9983PortConfEntry 3 }


g9983PortConfFecInterleaverType OBJECT-TYPE
	SYNTAX  INTEGER {
			none(0),
			block(1),
			convolution(2) }
	MAX-ACCESS read-write
	STATUS  current
	DESCRIPTION
		"An Interleaver type for G.Bond/TDIM ports supporting the
		FEC function.

		This object is read-write for the GBS-C ports and read-only
		for the GBS-R.

		A value of none(0) SHALL be returned if the FEC function is
		disabled (via g9983PortConfFecAdminState) or not supported.

		Changing of the Interleaver type MUST be performed when the
		FEC-enabled link is 'down'.  Attempts to change this object MUST
		be rejected if the link is 'up' or initializing or if the FEC
		function is disabled/not supported.

		This object maps to the TR-159/G.998.3 attribute
		aFECInterleaverType."
	REFERENCE
		"[TR-159], Section 5.5.4.9; [G.998.3], Appendix II, B-XIII"
	-- 1.3.6.1.2.1.210.1.1.1.1.4
	::= { g9983PortConfEntry 4 }


g9983PortConfFecInterleaverDepth OBJECT-TYPE
	SYNTAX  Unsigned32 (0 | 1 | 2 | 3 | 4 | 6 | 8 | 12 | 16 | 24 | 32 | 48 | 96)
	MAX-ACCESS read-write
	STATUS  current
	DESCRIPTION
		"An Interleaver depth for G.Bond/TDIM ports supporting the
		FEC function.

		This object is read-write for the GBS-C ports and read-only
		for the GBS-R.

		A value of zero SHALL be returned if the FEC function is
		disabled (via g9983PortConfFecAdminState) or not supported.







		Changing of the Interleaver depth MUST be performed when the
		FEC-enabled link is 'down'.  Attempts to change this object MUST
		be rejected if the link is 'up' or initializing or if the FEC
		function is disabled/not supported.

		This object maps to the TR-159/G.998.3 attribute
		aFECInterleaverDepth."
	REFERENCE
		"[TR-159], Section 5.5.4.10; [G.998.3], Appendix II, B-XIV"
	-- 1.3.6.1.2.1.210.1.1.1.1.5
	::= { g9983PortConfEntry 5 }


g9983PortConfAdminServices OBJECT-TYPE
	SYNTAX  G9983SvcIndexList
	MAX-ACCESS read-write
	STATUS  current
	DESCRIPTION
		"Desired list of services for a G.Bond/TDIM port.  This object
		is a list of pointers to entries in the g9983SvcTable.

		The value of this object is a continuous ordered list of up to
		60 indices (g9983SvcIdx) of the active services carried
		via the G.Bond/TDIM link.  The position of a service in the
		list determines its relative priority in cases of bandwidth
		degradation -- the priority decreases towards the end of the
		list, which means that the last service in the list would be
		suspended first when the bandwidth degrades.

		This object is writable and readable for the GBS-C ports.
		It is irrelevant for the GBS-R ports -- a zero-length octet
		string SHALL be returned on an attempt to read this object, and
		an attempt to change this object MUST be rejected in this case.

		Note that the current operational service list is available
		via the g9983OperSvcTable object.

		This object for a GBS-C port MAY be modified independently of
		the link's state, i.e., in-service and out-of-service.
		Attempts to set this object to a list with a member value that
		is not the value of the index for an active entry in the
		corresponding g9983SvcTable table MUST be rejected."
	REFERENCE
		"[G.998.3], Sections 10.2.3, 13.3.4.6-13.3.4.11"
	-- 1.3.6.1.2.1.210.1.1.1.1.6
	::= { g9983PortConfEntry 6 }


g9983PortConfSvcUpDownEnable OBJECT-TYPE
	SYNTAX  TruthValue
	MAX-ACCESS read-write
	STATUS  current
	DESCRIPTION
		"Indicates whether g9983SvcUp and g9983SvcDown
		notifications should be generated for this interface.

		A value of true(1) indicates that the notifications are enabled.
		A value of false(2) indicates that the notifications are
		disabled.

		This object maps to the TR-159 attribute
		aServiceUpDownEnable."
	REFERENCE
		"[TR-159], Section 5.5.5.6"
	-- 1.3.6.1.2.1.210.1.1.1.1.7
	::= { g9983PortConfEntry 7 }


g9983PortCapTable OBJECT-TYPE
	SYNTAX  SEQUENCE OF G9983PortCapEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"Table for capabilities of G.Bond/TDIM ports.  Entries in this
		table MUST be maintained in a persistent manner."
	-- 1.3.6.1.2.1.210.1.1.2
	::= { g9983Port 2 }


g9983PortCapEntry OBJECT-TYPE
	SYNTAX  G9983PortCapEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"An entry in the G.Bond/TDIM Port Capability table.
		Each entry represents a G.Bond/TDIM port indexed by the
		ifIndex.  Additional capabilities are available via the
		gBondPortCapabilityEntry of the GBOND-MIB.
		Note that a G.Bond/TDIM port runs on top of a single
		or multiple BCE port(s), which are also indexed by the ifIndex."
	INDEX {
		ifIndex }
	-- 1.3.6.1.2.1.210.1.1.2.1
	::= { g9983PortCapTable 1 }


G9983PortCapEntry ::= SEQUENCE {

	g9983PortCapFecSupported                TruthValue,
	g9983PortCapFecMaxWordSize              Unsigned32,
	g9983PortCapFecMaxRedundancySize        Unsigned32,
	g9983PortCapFecInterleaverTypeSupported INTEGER,
	g9983PortCapFecMaxInterleaverDepth      Unsigned32 }


g9983PortCapFecSupported OBJECT-TYPE
	SYNTAX  TruthValue
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"FEC and Interleaver capability of the G.Bond/TDIM port.
		This object has a value of true(1) when the port supports the
		FEC and Interleaver function.
		A value of false(2) is returned when the port does not
		support the FEC and Interleaver function.

		This object maps to the TR-159/G.998.3 attribute
		aFECSupported."
	REFERENCE
		"[TR-159], Section 5.5.4.4; [G.998.3], Appendix II, B-VI"
	-- 1.3.6.1.2.1.210.1.1.2.1.1
	::= { g9983PortCapEntry 1 }


g9983PortCapFecMaxWordSize OBJECT-TYPE
	SYNTAX  Unsigned32 (0 | 20..255)
	UNITS	"octets"
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"A maximum supported FEC code word size, in octets, for
		G.Bond/TDIM ports supporting the FEC function.

		A value of zero SHALL be returned if the FEC function is not
		supported.

		This object maps to the TR-159 attribute aFECWordSize."
	REFERENCE
		"[TR-159], Section 5.5.4.11; [G.998.3], Appendix II, B-XI"
	-- 1.3.6.1.2.1.210.1.1.2.1.2
	::= { g9983PortCapEntry 2 }


g9983PortCapFecMaxRedundancySize OBJECT-TYPE
	SYNTAX  Unsigned32 (0 | 2 | 4 | 8 | 16 | 20)
	UNITS	"octets"
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"A maximum supported FEC redundancy word size, in octets, for
		G.Bond/TDIM ports supporting the FEC function.

		A value of zero SHALL be returned if the FEC function is not
		supported.

		This object maps to the TR-159 attribute
		aFECMaxRedundancySize."
	REFERENCE
		"[TR-159], Section 5.5.4.12; [G.998.3], Appendix II, B-XII"
	-- 1.3.6.1.2.1.210.1.1.2.1.3
	::= { g9983PortCapEntry 3 }


g9983PortCapFecInterleaverTypeSupported OBJECT-TYPE
	SYNTAX  INTEGER {
			none(0),
			block(1),
			convolution(2),
			blockConvolution(3) }
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"Supported Interleaver types for G.Bond/TDIM ports supporting
		the FEC function.

		Possible values are:
		  none             - the port does not support interleaving
		  block            - the port supports Block Interleaver
		  convolution      - the port supports Convolution Interleaver
		  blockConvolution - the port supports both Block Interleaver
		                     and Convolution Interleaver

		This object maps to the TR-159 attribute
		aFECInterleaverTypesSupported."
	REFERENCE
		"[TR-159], Section 5.5.4.13; [G.998.3], Appendix II, B-XIII"
	-- 1.3.6.1.2.1.210.1.1.2.1.4
	::= { g9983PortCapEntry 4 }


g9983PortCapFecMaxInterleaverDepth OBJECT-TYPE
	SYNTAX  Unsigned32 (0 | 1 | 2 | 3 | 4 | 6 | 8 | 12 | 16 | 24 | 32 | 48 | 96)
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"A maximum Interleaver depth for G.Bond/TDIM ports supporting
		the FEC function.

		A value of zero SHALL be returned if the Interleaver is not
		supported.

		This object maps to the TR-159 attribute
		aFECMaxInterleaverDepth."
	REFERENCE
		"[TR-159], Section 5.5.4.14; [G.998.3], Appendix II, B-XIV"
	-- 1.3.6.1.2.1.210.1.1.2.1.5
	::= { g9983PortCapEntry 5 }


g9983PortStatTable OBJECT-TYPE
	SYNTAX  SEQUENCE OF G9983PortStatEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"This table provides overall status information of G.Bond
		TDIM ports, complementing the generic status information from
		the ifTable of the IF-MIB and the gBondPortStatFltStatus of
		the GBOND-MIB.  Additional status information about connected
		BCEs is available from the relevant line MIBs.

		This table contains live data from the equipment.  As such,
		it is NOT persistent."
	-- 1.3.6.1.2.1.210.1.1.3
	::= { g9983Port 3 }


g9983PortStatEntry OBJECT-TYPE
	SYNTAX  G9983PortStatEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"An entry in the G.Bond/TDIM Port Status table.
		Each entry represents a G.Bond/TDIM port indexed by the
		ifIndex.
		Note that a G.Bond GBS port runs on top of a single
		or multiple BCE port(s), which are also indexed by the ifIndex."
	INDEX {
		ifIndex }
	-- 1.3.6.1.2.1.210.1.1.3.1
	::= { g9983PortStatTable 1 }


G9983PortStatEntry ::= SEQUENCE {

	g9983PortStatFecOperState TruthValue,
	g9983PortStatFltStatus    BITS,
	g9983PortStatCrc4Errors   Counter32,
	g9983PortStatCrc6Errors   Counter32,
	g9983PortStatCrc8Errors   Counter32 }


g9983PortStatFecOperState OBJECT-TYPE
	SYNTAX  TruthValue
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"A read-only value indicating the current operational state
		of the OPTIONAL Forward Error Correction (FEC) function for
		the G.998.3 port.
		A value of 'false' indicates that the FEC function is
		disabled.  A value of 'true' indicates that the FEC function
		is enabled (and supported).





		This object maps to the TR-159 attribute aFECOperState."
	REFERENCE
		"[TR-159], Section 5.5.4.6"
	-- 1.3.6.1.2.1.210.1.1.3.1.1
	::= { g9983PortStatEntry 1 }


g9983PortStatFltStatus OBJECT-TYPE
	SYNTAX  BITS {
			serviceDown(0),
			wrongConfig(1) }
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"G.Bond/TDIM port fault status.  This is a bitmap of possible
		conditions.  The various bit positions are:
		  serviceDown         - at least one of the services defined
		                        for this aggregation group is down
		                        (due to low rate).
		  wrongConfig         - at least one BCE at the remote GBS-R
		                        is already connected to another GBS.

		This object is intended to supplement the ifOperStatus object
		in the IF-MIB and the gBondPortStatFltStatus object in the
		GBOND-MIB."
	REFERENCE
		"[G.998.3], Section 6.3; RFC 2863, IF-MIB, ifOperStatus;
		RFC 6765, GBOND-MIB, gBondPortStatFltStatus"
	-- 1.3.6.1.2.1.210.1.1.3.1.2
	::= { g9983PortStatEntry 2 }


g9983PortStatCrc4Errors OBJECT-TYPE
	SYNTAX  Counter32
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The total number of CRC-4 errors (frame header errors) on all
		pairs in the G.Bond/TDIM port.  Simultaneous errors on M lines
		SHOULD be counted M times.

		Discontinuities in the value of this counter can occur at
		re-initialization of the management system, and at other times
		as indicated by the value of ifCounterDiscontinuityTime as
		defined in the IF-MIB.

		This object maps to the TR-159/G.998.3 attribute aCRC4Errors."
	REFERENCE
		"[TR-159], Section 5.5.4.1; [G.998.3], Appendix II, B-VII"
	-- 1.3.6.1.2.1.210.1.1.3.1.3
	::= { g9983PortStatEntry 3 }


g9983PortStatCrc6Errors OBJECT-TYPE
	SYNTAX  Counter32
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The total number of CRC-6 errors (super-frame errors) on all
		pairs in the G.Bond/TDIM port.  Simultaneous errors on M lines
		SHOULD be counted 1 time.

		Discontinuities in the value of this counter can occur at
		re-initialization of the local management subsystem, and at
		other times as indicated by the value of
		ifCounterDiscontinuityTime as defined in the IF-MIB.

		This object maps to the TR-159/G.998.3 attribute aCRC6Errors."
	REFERENCE
		"[TR-159], Section 5.5.4.2; [G.998.3], Appendix II, B-VIII"
	-- 1.3.6.1.2.1.210.1.1.3.1.4
	::= { g9983PortStatEntry 4 }


g9983PortStatCrc8Errors OBJECT-TYPE
	SYNTAX  Counter32
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"The total number of CRC-8 errors (event/message errors) on all
		pairs in the G.Bond/TDIM port.  Simultaneous errors on M lines
		SHOULD be counted M times.

		Discontinuities in the value of this counter can occur at
		re-initialization of the local management subsystem, and at
		other times as indicated by the value of
		ifCounterDiscontinuityTime as defined in the IF-MIB.

		This object maps to the TR-159/G.998.3 attribute aCRC8Errors."
	REFERENCE
		"[TR-159], Section 5.5.4.3; [G.998.3], Appendix II, B-IX"
	-- 1.3.6.1.2.1.210.1.1.3.1.5
	::= { g9983PortStatEntry 5 }


g9983OperSvcTable OBJECT-TYPE
	SYNTAX  SEQUENCE OF G9983OperSvcEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"Table of the operational services configured on a G.Bond/TDIM
		port.  This table reflects current actual service configuration,
		set by the g9983PortConfAdminServices object.  The number of
		entries (services) in this table therefore can vary between





		0, when no services are configured, and 60, for the maximum
		number of services.
		This table contains live data from the equipment.  As such,
		it is NOT persistent."
	-- 1.3.6.1.2.1.210.1.1.4
	::= { g9983Port 4 }


g9983OperSvcEntry OBJECT-TYPE
	SYNTAX  G9983OperSvcEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"An entry in the G.Bond/TDIM Port Operational Service table,
		containing the index of an active service entry in the
		g9983SvcTable.  The entry is indexed by the ifIndex,
		indicating a corresponding G.Bond/TDIM port, and by
		g9983OperSvcPosition (1..60), indicating the
		corresponding service position in the G.Bond/TDIM frame."
	INDEX {
		ifIndex,
		g9983OperSvcPosition }
	-- 1.3.6.1.2.1.210.1.1.4.1
	::= { g9983OperSvcTable 1 }


G9983OperSvcEntry ::= SEQUENCE {

	g9983OperSvcPosition G9983SvcOrderIndex,
	g9983OperSvcIdx      G9983SvcIndex,
	g9983OperSvcState    INTEGER }


g9983OperSvcPosition OBJECT-TYPE
	SYNTAX  G9983SvcOrderIndex
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"G.Bond/TDIM operational service position -- a unique index,
		indicating relative placement of the associated service
		pointed to by g9983OperSvcIdx, within the G.Bond/TDIM frame.

		There can be up to 60 services defined over a TDIM bonded
		facility.  Services with lower indices have higher priority in
		cases of bandwidth degradation.

		The value of g9983OperSvcPosition for the first
		g9983OperSvcEntry is always 1, incrementing sequentially
		for each consecutive entry, i.e., 2 for the second entry,
		3 for the third, etc.

		This objects maps to the TR-159/G.998.3 attribute aServiceID."
	REFERENCE
		"[TR-159], Section 5.5.5.1; [G.998.3], Appendix II, C-I"
	-- 1.3.6.1.2.1.210.1.1.4.1.1
	::= { g9983OperSvcEntry 1 }


g9983OperSvcIdx OBJECT-TYPE
	SYNTAX  G9983SvcIndex
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"G.Bond/TDIM operational service index -- a read-only pointer
		to an existing entry in the g9983SvcTable (value of
		g9983SvcIdx) describing a particular service."
	-- 1.3.6.1.2.1.210.1.1.4.1.2
	::= { g9983OperSvcEntry 2 }


g9983OperSvcState OBJECT-TYPE
	SYNTAX  INTEGER {
			up(1),
			down(2) }
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"G.Bond/TDIM service operational state.

		Possible values are:
		  up                  - Service is up and passing traffic.
		  down                - Service is down, due to a variety of
		                        reasons, e.g., G.Bond/TDIM port is
		                        down, current link bandwidth is too
		                        low to support a particular service,
		                        etc.
		This objects maps to the TR-159 attribute aServiceOperState."
	REFERENCE
		"[TR-159], Section 5.5.5.5"
	-- 1.3.6.1.2.1.210.1.1.4.1.3
	::= { g9983OperSvcEntry 3 }


g9983SvcTable OBJECT-TYPE
	SYNTAX  SEQUENCE OF G9983SvcEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"Table of possible services for G.Bond/TDIM ports.
		Entries in this table MUST be maintained in a persistent
		manner."
	-- 1.3.6.1.2.1.210.1.1.5
	::= { g9983Port 5 }


g9983SvcEntry OBJECT-TYPE
	SYNTAX  G9983SvcEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"An entry in the G.Bond/TDIM Port Service table, containing
		the management information applicable to a particular service,
		indexed by the g9983SvcIdx, on a G.Bond/TDIM port,
		indexed by the ifIndex."
	INDEX {
		ifIndex,
		g9983SvcIdx }
	-- 1.3.6.1.2.1.210.1.1.5.1
	::= { g9983SvcTable 1 }


G9983SvcEntry ::= SEQUENCE {

	g9983SvcIdx       G9983SvcIndex,
	g9983SvcIfIdx     InterfaceIndex,
	g9983SvcType      INTEGER,
	g9983SvcSize      Unsigned32,
	g9983SvcRowStatus RowStatus }


g9983SvcIdx OBJECT-TYPE
	SYNTAX  G9983SvcIndex
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"G.Bond/TDIM service index -- a unique index associated with
		a particular service entry."
	-- 1.3.6.1.2.1.210.1.1.5.1.1
	::= { g9983SvcEntry 1 }


g9983SvcIfIdx OBJECT-TYPE
	SYNTAX  InterfaceIndex
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"This is a unique index within the ifTable.  It represents
		the interface index of a service to be transmitted over the
		G.Bond/TDIM service instance.

		This objects maps to the TR-159 attribute aServiceIfIndex."
	REFERENCE
		"[TR-159], Section 5.5.5.2"
	-- 1.3.6.1.2.1.210.1.1.5.1.2
	::= { g9983SvcEntry 2 }


g9983SvcType OBJECT-TYPE
	SYNTAX  INTEGER {
			ds1(0),
			e1(1),
			nxds0(2),
			nxe0(3),
			ds3(4),
			e3(5),
			clock(6),
			ethernet(7),
			atm(8),
			gfpNoFCS(9),
			gfp(10) }
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"G.Bond/TDIM service type.

		Possible values are:
		  ds1            - Clear Channel DS1 (synchronous)
		  e1             - Clear Channel E1 (synchronous)
		  nxds0          - Fractional DS1 (synchronous)
		  nxe0           - Fractional E1 (synchronous)
		  ds3            - DS3 (synchronous)
		  e3             - E3 (synchronous)
		  clock          - Clock transfer (synchronous)
		  ethernet       - Ethernet (asynchronous)
		  atm            - ATM (asynchronous)
		  gfpNoFCS       - GFP encapsulated without FCS (asynchronous)
		  gfp            - GFP encapsulated with FCS (asynchronous)

		For the GBS-R ports, the value of this object cannot be
		changed directly.  This value may be changed as a result of a
		write operation on the g9983SvcType object of a remote GBS-C.

		Attempts to change this object MUST be rejected for the GBS-R
		ports.

		This object maps to the TR-159/G.998.3 attribute aServiceType."
	REFERENCE
		"[TR-159], Section 5.5.5.3; [G.998.3], Appendix II, C-II"
	-- 1.3.6.1.2.1.210.1.1.5.1.3
	::= { g9983SvcEntry 3 }


g9983SvcSize OBJECT-TYPE
	SYNTAX  Unsigned32 (0 | 20..255)
	UNITS	"octets"
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"Service size, in octets, per bonding sub-block for a specific
		service identified by g9983SvcIdx.





		For TDM (synchronous) services with variable size
		(e.g., fractional DS1/E1), this object represents the number of
		DS0/E0 channels.
		For asynchronous services (Ethernet, ATM, GFPnoFCS, or GFP),
		this object represents the maximum number of octets.
		For non-fractional TDM services (i.e., DS1, E1, DS3, E3, and
		clock), the value of this object MUST be 0.

		A GET operation returns the current value.
		A SET operation, allowed on GBS-C ports, changes the service
		size to the indicated value.  If the service type is a
		fixed-rate synchronous service (g9983SvcType is nxds0, nxe0,
		ds1, e1, ds3, e3, or clock), the operation MUST be rejected.

		This object maps to the TR-159/G.998.3 attribute aServiceSize."
	REFERENCE
		"[TR-159], Section 5.5.5.4; [G.998.3], Appendix II, C-III"
	-- 1.3.6.1.2.1.210.1.1.5.1.4
	::= { g9983SvcEntry 4 }


g9983SvcRowStatus OBJECT-TYPE
	SYNTAX  RowStatus
	MAX-ACCESS read-create
	STATUS  current
	DESCRIPTION
		"This object controls the creation, modification, or deletion
		of the associated entry in the g9983SvcTable per the
		semantics of RowStatus.

		If an 'active' entry is referenced via g9983OperSvcIdx
		or a g9983PortConfAdminServices instance, or indexes a
		g9983SvcPm*Entry, the entry MUST remain 'active'.

		An 'active' entry SHALL NOT be modified.  In order to modify an
		existing entry, it MUST be taken out of service (by setting
		this object to 'notInService'), modified, and set to 'active'
		again."
	-- 1.3.6.1.2.1.210.1.1.5.1.5
	::= { g9983SvcEntry 5 }


-------------------------------
-- Performance Monitoring group
-------------------------------

g9983PM OBJECT IDENTIFIER 
	-- 1.3.6.1.2.1.210.1.1.6
	::= { g9983Port 6 }

g9983PortPmCurTable OBJECT-TYPE
	SYNTAX  SEQUENCE OF G9983PortPmCurEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"This table contains current Performance Monitoring information
		for a G.Bond/TDIM port.  This table contains live data from the
		equipment and as such is NOT persistent."
	-- 1.3.6.1.2.1.210.1.1.6.1
	::= { g9983PM 1 }


g9983PortPmCurEntry OBJECT-TYPE
	SYNTAX  G9983PortPmCurEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"An entry in the G.Bond/TDIM Port PM table.
		Each entry represents a G.Bond/TDIM port indexed by the
		ifIndex."
	INDEX {
		ifIndex }
	-- 1.3.6.1.2.1.210.1.1.6.1.1
	::= { g9983PortPmCurTable 1 }


G9983PortPmCurEntry ::= SEQUENCE {

	g9983PortPmCur15MinValidIntervals   HCPerfValidIntervals,
	g9983PortPmCur15MinInvalidIntervals HCPerfInvalidIntervals,
	g9983PortPmCur15MinTimeElapsed      HCPerfTimeElapsed,
	g9983PortPmCur15MinCrc4s            HCPerfCurrentCount,
	g9983PortPmCur15MinCrc6s            HCPerfCurrentCount,
	g9983PortPmCur15MinCrc8s            HCPerfCurrentCount,
	g9983PortPmCur1DayValidIntervals    Unsigned32,
	g9983PortPmCur1DayInvalidIntervals  Unsigned32,
	g9983PortPmCur1DayTimeElapsed       HCPerfTimeElapsed,
	g9983PortPmCur1DayCrc4s             HCPerfCurrentCount,
	g9983PortPmCur1DayCrc6s             HCPerfCurrentCount,
	g9983PortPmCur1DayCrc8s             HCPerfCurrentCount }


g9983PortPmCur15MinValidIntervals OBJECT-TYPE
	SYNTAX  HCPerfValidIntervals
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"A read-only number of 15-minute intervals for which the
		performance data was collected.  The value of this object will
		be 96 or the maximum number of 15-minute history intervals
		collected by the implementation, unless the measurement was
		(re)started recently, in which case the value will be the
		number of complete 15-minute intervals for which there are at
		least some data.







		In certain cases, it is possible that some intervals are
		unavailable.  In this case, this object reports the maximum
		interval number for which data is available.

		This object partially maps to the TR-159 attribute
		aGroupPerf15MinValidIntervals."
	REFERENCE
		"[TR-159], Section 5.5.1.32"
	-- 1.3.6.1.2.1.210.1.1.6.1.1.1
	::= { g9983PortPmCurEntry 1 }


g9983PortPmCur15MinInvalidIntervals OBJECT-TYPE
	SYNTAX  HCPerfInvalidIntervals
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"A read-only number of 15-minute intervals for which the
		performance data was not always available.  The value will
		typically be zero, except in cases where the data for some
		intervals are not available.

		This object partially maps to the TR-159 attribute
		aGroupPerf15MinInvalidIntervals."
	REFERENCE
		"[TR-159], Section 5.5.1.33"
	-- 1.3.6.1.2.1.210.1.1.6.1.1.2
	::= { g9983PortPmCurEntry 2 }


g9983PortPmCur15MinTimeElapsed OBJECT-TYPE
	SYNTAX  HCPerfTimeElapsed
	UNITS	"seconds"
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"A read-only count of seconds that have elapsed since the
		beginning of the current 15-minute performance interval.

		This object partially maps to the TR-159 attribute
		aGroupPerfCurr15MinTimeElapsed."
	REFERENCE
		"[TR-159], Section 5.5.1.34"
	-- 1.3.6.1.2.1.210.1.1.6.1.1.3
	::= { g9983PortPmCurEntry 3 }


g9983PortPmCur15MinCrc4s OBJECT-TYPE
	SYNTAX  HCPerfCurrentCount
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"A read-only count of CRC-4 errors (frame header errors) on all
		active pairs in the G.Bond/TDIM port during the current





		15-minute performance interval.
		Simultaneous errors on M lines SHOULD be counted M times.

		Note that the total number of CRC-4 errors is indicated by the
		g9983PortStatCrc4Errors object.

		This object is inhibited during Severely Errored Seconds (SES)
		or Unavailable Seconds (UAS)."
	REFERENCE
		"[TR-159], Section 5.5.4.1"
	-- 1.3.6.1.2.1.210.1.1.6.1.1.4
	::= { g9983PortPmCurEntry 4 }


g9983PortPmCur15MinCrc6s OBJECT-TYPE
	SYNTAX  HCPerfCurrentCount
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"A read-only count of CRC-6 errors (super-frame errors) on all
		active pairs in the G.Bond/TDIM port during the current
		15-minute performance interval.
		Simultaneous errors on M lines SHOULD be counted 1 time.

		Note that the total number of CRC-6 errors is indicated by the
		g9983PortStatCrc6Errors object.

		This object is inhibited during Unavailable Seconds (UAS)."
	REFERENCE
		"[TR-159], Section 5.5.4.2"
	-- 1.3.6.1.2.1.210.1.1.6.1.1.5
	::= { g9983PortPmCurEntry 5 }


g9983PortPmCur15MinCrc8s OBJECT-TYPE
	SYNTAX  HCPerfCurrentCount
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"A read-only count of CRC-8 errors (event/message errors) on all
		active pairs in the G.Bond/TDIM port during the current
		15-minute performance interval.
		Simultaneous errors on M lines SHOULD be counted M times.

		Note that the total number of CRC-8 errors is indicated by the
		g9983PortStatCrc8Errors object.

		This object is inhibited during Unavailable Seconds (UAS)."
	REFERENCE
		"[TR-159], Section 5.5.4.3"
	-- 1.3.6.1.2.1.210.1.1.6.1.1.6
	::= { g9983PortPmCurEntry 6 }


g9983PortPmCur1DayValidIntervals OBJECT-TYPE
	SYNTAX  Unsigned32 (0..7)
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"A read-only number of 1-day intervals for which data was
		collected.  The value of this object will be 7 or the maximum
		number of 1-day history intervals collected by the
		implementation, unless the measurement was (re)started recently,
		in which case the value will be the number of complete 1-day
		intervals for which there are at least some data.
		In certain cases, it is possible that some intervals are
		unavailable.  In this case, this object reports the maximum
		interval number for which data is available."
	REFERENCE
		"[TR-159], Section 5.5.1.45"
	-- 1.3.6.1.2.1.210.1.1.6.1.1.7
	::= { g9983PortPmCurEntry 7 }


g9983PortPmCur1DayInvalidIntervals OBJECT-TYPE
	SYNTAX  Unsigned32 (0..7)
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"A read-only number of 1-day intervals for which data was
		not always available.  The value will typically be zero, except
		in cases where the data for some intervals are not available."
	REFERENCE
		"[TR-159], Section 5.5.1.46"
	-- 1.3.6.1.2.1.210.1.1.6.1.1.8
	::= { g9983PortPmCurEntry 8 }


g9983PortPmCur1DayTimeElapsed OBJECT-TYPE
	SYNTAX  HCPerfTimeElapsed
	UNITS	"seconds"
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"A read-only count of seconds that have elapsed since the
		beginning of the current 1-day performance interval."
	REFERENCE
		"[TR-159], Section 5.5.1.47"
	-- 1.3.6.1.2.1.210.1.1.6.1.1.9
	::= { g9983PortPmCurEntry 9 }


g9983PortPmCur1DayCrc4s OBJECT-TYPE
	SYNTAX  HCPerfCurrentCount
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"A read-only count of CRC-4 errors on the G.Bond/TDIM port in
		the current 1-day performance interval.

		This object is inhibited during Severely Errored Seconds (SES)
		and Unavailable Seconds (UAS)."
	-- 1.3.6.1.2.1.210.1.1.6.1.1.10
	::= { g9983PortPmCurEntry 10 }


g9983PortPmCur1DayCrc6s OBJECT-TYPE
	SYNTAX  HCPerfCurrentCount
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"A read-only count of CRC-6 errors on the G.Bond/TDIM port
		in the current 1-day performance interval.

		This object is inhibited during Unavailable Seconds (UAS)."
	-- 1.3.6.1.2.1.210.1.1.6.1.1.11
	::= { g9983PortPmCurEntry 11 }


g9983PortPmCur1DayCrc8s OBJECT-TYPE
	SYNTAX  HCPerfCurrentCount
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"A read-only count of CRC-8 errors on the G.Bond/TDIM port in
		the current 1-day performance interval.

		This object is inhibited during Unavailable Seconds (UAS)."
	-- 1.3.6.1.2.1.210.1.1.6.1.1.12
	::= { g9983PortPmCurEntry 12 }


-- Port PM history: 15-min buckets

g9983PortPm15MinTable OBJECT-TYPE
	SYNTAX  SEQUENCE OF G9983PortPm15MinEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"This table contains historical 15-minute buckets of Performance
		Monitoring information for a G.Bond/TDIM port (a row for each
		15-minute interval, up to 96 intervals).
		Entries in this table MUST be maintained in a persistent manner."
	-- 1.3.6.1.2.1.210.1.1.6.2
	::= { g9983PM 2 }


g9983PortPm15MinEntry OBJECT-TYPE
	SYNTAX  G9983PortPm15MinEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"An entry in the G.Bond/TDIM Port historical 15-minute PM table.
		Each entry represents Performance Monitoring data for a G.Bond
		TDIM port, indexed by the ifIndex, collected during a particular
		15-minute interval, indexed by the
		g9983PortPm15MinIntervalIndex."
	INDEX {
		ifIndex,
		g9983PortPm15MinIntervalIndex }
	-- 1.3.6.1.2.1.210.1.1.6.2.1
	::= { g9983PortPm15MinTable 1 }


G9983PortPm15MinEntry ::= SEQUENCE {

	g9983PortPm15MinIntervalIndex    Unsigned32,
	g9983PortPm15MinIntervalMoniTime HCPerfTimeElapsed,
	g9983PortPm15MinIntervalCrc4s    HCPerfIntervalCount,
	g9983PortPm15MinIntervalCrc6s    HCPerfIntervalCount,
	g9983PortPm15MinIntervalCrc8s    HCPerfIntervalCount,
	g9983PortPm15MinIntervalValid    TruthValue }


g9983PortPm15MinIntervalIndex OBJECT-TYPE
	SYNTAX  Unsigned32 (1..96)
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"Performance data interval number.  1 is the most recent
		previous interval; interval 96 is 24 hours ago.
		Intervals 2..96 are OPTIONAL.

		This object partially maps to the TR-159 attribute
		aGroupPerf15MinIntervalNumber."
	REFERENCE
		"[TR-159], Section 5.5.1.57"
	-- 1.3.6.1.2.1.210.1.1.6.2.1.1
	::= { g9983PortPm15MinEntry 1 }


g9983PortPm15MinIntervalMoniTime OBJECT-TYPE
	SYNTAX  HCPerfTimeElapsed
	UNITS	"seconds"
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"A read-only count of seconds over which the performance data
		was actually monitored.  This value will be the same as the
		interval duration (900 seconds), except in a situation where
		performance data could not be collected for any reason."
	-- 1.3.6.1.2.1.210.1.1.6.2.1.2
	::= { g9983PortPm15MinEntry 2 }


g9983PortPm15MinIntervalCrc4s OBJECT-TYPE
	SYNTAX  HCPerfIntervalCount
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"A read-only count of CRC-4 errors on the G.Bond/TDIM port
		during the 15-minute performance history interval.

		This object is inhibited during Severely Errored Seconds (SES)
		and Unavailable Seconds (UAS)."
	-- 1.3.6.1.2.1.210.1.1.6.2.1.3
	::= { g9983PortPm15MinEntry 3 }


g9983PortPm15MinIntervalCrc6s OBJECT-TYPE
	SYNTAX  HCPerfIntervalCount
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"A read-only count of CRC-6 errors on the G.Bond/TDIM port
		during the 15-minute performance history interval.

		This object is inhibited during Unavailable Seconds (UAS)."
	-- 1.3.6.1.2.1.210.1.1.6.2.1.4
	::= { g9983PortPm15MinEntry 4 }


g9983PortPm15MinIntervalCrc8s OBJECT-TYPE
	SYNTAX  HCPerfIntervalCount
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"A read-only count of CRC-8 errors on the G.Bond/TDIM port
		during the current 15-minute performance interval.

		This object is inhibited during Unavailable Seconds (UAS)."
	-- 1.3.6.1.2.1.210.1.1.6.2.1.5
	::= { g9983PortPm15MinEntry 5 }


g9983PortPm15MinIntervalValid OBJECT-TYPE
	SYNTAX  TruthValue
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"A read-only object indicating whether or not this history
		bucket contains valid data.  A valid bucket is reported as
		true(1) and an invalid bucket as false(2).
		If this history bucket is invalid, the BTU-C MUST NOT produce
		notifications based upon the value of the counters in this
		bucket.
		Note that an implementation may decide not to store invalid
		history buckets in its database.  In such a case, this object
		is not required, as only valid history buckets are available
		while invalid history buckets are simply not in the database.






		This object partially maps to the TR-159 attribute
		aGroupPerf15MinIntervalValid."
	REFERENCE
		"[TR-159], Section 5.5.1.58"
	-- 1.3.6.1.2.1.210.1.1.6.2.1.6
	::= { g9983PortPm15MinEntry 6 }


-- Port PM history: 1-day buckets

g9983PortPm1DayTable OBJECT-TYPE
	SYNTAX  SEQUENCE OF G9983PortPm1DayEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"This table contains historical 1-day buckets of Performance
		Monitoring information for a G.Bond/TDIM port (a row for each
		1-day interval, up to 7 intervals).
		Entries in this table MUST be maintained in a persistent manner."
	-- 1.3.6.1.2.1.210.1.1.6.3
	::= { g9983PM 3 }


g9983PortPm1DayEntry OBJECT-TYPE
	SYNTAX  G9983PortPm1DayEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"An entry in the G.Bond/TDIM Port historical 1-day PM table.
		Each entry represents Performance Monitoring data for such a
		port, indexed by the ifIndex, collected during a particular
		1-day interval, indexed by the g9983PortPm1DayIntervalIndex."
	INDEX {
		ifIndex,
		g9983PortPm1DayIntervalIndex }
	-- 1.3.6.1.2.1.210.1.1.6.3.1
	::= { g9983PortPm1DayTable 1 }


G9983PortPm1DayEntry ::= SEQUENCE {

	g9983PortPm1DayIntervalIndex    Unsigned32,
	g9983PortPm1DayIntervalMoniTime HCPerfTimeElapsed,
	g9983PortPm1DayIntervalCrc4s    HCPerfIntervalCount,
	g9983PortPm1DayIntervalCrc6s    HCPerfIntervalCount,
	g9983PortPm1DayIntervalCrc8s    HCPerfIntervalCount,
	g9983PortPm1DayIntervalValid    TruthValue }


g9983PortPm1DayIntervalIndex OBJECT-TYPE
	SYNTAX  Unsigned32 (1..7)
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"Performance data interval number.  1 is the most recent
		previous interval; interval 7 is 7 days ago.





		Intervals 2..7 are OPTIONAL.

		This object partially maps to the TR-159 attribute
		aGroupPerf1DayIntervalNumber."
	REFERENCE
		"[TR-159], Section 5.5.1.62"
	-- 1.3.6.1.2.1.210.1.1.6.3.1.1
	::= { g9983PortPm1DayEntry 1 }


g9983PortPm1DayIntervalMoniTime OBJECT-TYPE
	SYNTAX  HCPerfTimeElapsed
	UNITS	"seconds"
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"A read-only count of seconds over which the performance data
		was actually monitored.  This value will be the same as the
		interval duration (86400 seconds), except in a situation where
		performance data could not be collected for any reason.

		This object partially maps to the TR-159 attribute
		aGroupPerf1DayIntervalMoniSecs."
	REFERENCE
		"[TR-159], Section 5.5.1.64"
	-- 1.3.6.1.2.1.210.1.1.6.3.1.2
	::= { g9983PortPm1DayEntry 2 }


g9983PortPm1DayIntervalCrc4s OBJECT-TYPE
	SYNTAX  HCPerfIntervalCount
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"A read-only count of CRC-4 errors on the G.Bond/TDIM port
		during the 1-day performance history interval.

		This object is inhibited during Severely Errored Seconds (SES)
		and Unavailable Seconds (UAS)."
	-- 1.3.6.1.2.1.210.1.1.6.3.1.3
	::= { g9983PortPm1DayEntry 3 }


g9983PortPm1DayIntervalCrc6s OBJECT-TYPE
	SYNTAX  HCPerfIntervalCount
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"A read-only count of CRC-6 errors on the G.Bond/TDIM port
		during the 1-day performance history interval.

		This object is inhibited during Unavailable Seconds (UAS)."
	-- 1.3.6.1.2.1.210.1.1.6.3.1.4
	::= { g9983PortPm1DayEntry 4 }


g9983PortPm1DayIntervalCrc8s OBJECT-TYPE
	SYNTAX  HCPerfIntervalCount
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"A read-only count of CRC-8 errors on the G.Bond/TDIM port
		during the current 1-day performance interval.

		This object is inhibited during Unavailable Seconds (UAS)."
	-- 1.3.6.1.2.1.210.1.1.6.3.1.5
	::= { g9983PortPm1DayEntry 5 }


g9983PortPm1DayIntervalValid OBJECT-TYPE
	SYNTAX  TruthValue
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"A read-only object indicating whether or not this history
		bucket contains valid data.  A valid bucket is reported as
		true(1) and an invalid bucket as false(2).
		If this history bucket is invalid, the BTU-C MUST NOT produce
		notifications based upon the value of the counters in this
		bucket.
		Note that an implementation may decide not to store invalid
		history buckets in its database.  In such a case, this object
		is not required, as only valid history buckets are available
		while invalid history buckets are simply not in the database.

		This object partially maps to the TR-159 attribute
		aGroupPerf1DayIntervalValid."
	REFERENCE
		"[TR-159], Section 5.5.1.63"
	-- 1.3.6.1.2.1.210.1.1.6.3.1.6
	::= { g9983PortPm1DayEntry 6 }


-- Services PM

g9983SvcPmCurTable OBJECT-TYPE
	SYNTAX  SEQUENCE OF G9983SvcPmCurEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"This table contains current Performance Monitoring information
		for the services of a G.Bond/TDIM port.
		This table contains live data from the equipment and as such is
		NOT persistent."
	-- 1.3.6.1.2.1.210.1.1.6.4
	::= { g9983PM 4 }


g9983SvcPmCurEntry OBJECT-TYPE
	SYNTAX  G9983SvcPmCurEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"An entry in the G.Bond/TDIM Services PM table.
		Each entry represents a service, indexed by the
		g9983SvcIdx, in a G.Bond/TDIM port, indexed by the
		ifIndex."
	INDEX {
		ifIndex,
		g9983SvcIdx }
	-- 1.3.6.1.2.1.210.1.1.6.4.1
	::= { g9983SvcPmCurTable 1 }


G9983SvcPmCurEntry ::= SEQUENCE {

	g9983SvcPmCur15MinValidIntervals   HCPerfValidIntervals,
	g9983SvcPmCur15MinInvalidIntervals HCPerfInvalidIntervals,
	g9983SvcPmCur15MinTimeElapsed      HCPerfTimeElapsed,
	g9983SvcPmCur15MinDowns            HCPerfCurrentCount,
	g9983SvcPmCur1DayValidIntervals    Unsigned32,
	g9983SvcPmCur1DayInvalidIntervals  Unsigned32,
	g9983SvcPmCur1DayTimeElapsed       HCPerfTimeElapsed,
	g9983SvcPmCur1DayDowns             HCPerfCurrentCount }


g9983SvcPmCur15MinValidIntervals OBJECT-TYPE
	SYNTAX  HCPerfValidIntervals
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"A read-only number of 15-minute intervals for which the
		performance data was collected.  The value of this object will
		be 96 or the maximum number of 15-minute history intervals
		collected by the implementation, unless the measurement was
		(re)started recently, in which case the value will be the
		number of complete 15-minute intervals for which there are at
		least some data.
		In certain cases, it is possible that some intervals are
		unavailable.  In this case, this object reports the maximum
		interval number for which data is available.

		This object partially maps to the TR-159 attribute
		aGroupPerf15MinValidIntervals."
	REFERENCE
		"[TR-159], Section 5.5.1.32"
	-- 1.3.6.1.2.1.210.1.1.6.4.1.1
	::= { g9983SvcPmCurEntry 1 }


g9983SvcPmCur15MinInvalidIntervals OBJECT-TYPE
	SYNTAX  HCPerfInvalidIntervals
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"A read-only number of 15-minute intervals for which the
		performance data was not always available.  The value will
		typically be zero, except in cases where the data for some
		intervals are not available.

		This object partially maps to the TR-159 attribute
		aGroupPerf15MinInvalidIntervals."
	REFERENCE
		"[TR-159], Section 5.5.1.33"
	-- 1.3.6.1.2.1.210.1.1.6.4.1.2
	::= { g9983SvcPmCurEntry 2 }


g9983SvcPmCur15MinTimeElapsed OBJECT-TYPE
	SYNTAX  HCPerfTimeElapsed
	UNITS	"seconds"
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"A read-only count of seconds that have elapsed since the
		beginning of the current 15-minute performance interval.

		This object partially maps to the TR-159 attribute
		aGroupPerfCurr15MinTimeElapsed."
	REFERENCE
		"[TR-159], Section 5.5.1.34"
	-- 1.3.6.1.2.1.210.1.1.6.4.1.3
	::= { g9983SvcPmCurEntry 3 }


g9983SvcPmCur15MinDowns OBJECT-TYPE
	SYNTAX  HCPerfCurrentCount
	UNITS	"seconds"
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"A read-only count of seconds in the current 15-minute
		performance interval during which a particular TDIM
		service was 'down', as indicated by the
		g9983OperSvcState object.

		This object is inhibited during Unavailable Seconds (UAS)."
	-- 1.3.6.1.2.1.210.1.1.6.4.1.4
	::= { g9983SvcPmCurEntry 4 }


g9983SvcPmCur1DayValidIntervals OBJECT-TYPE
	SYNTAX  Unsigned32 (0..7)
	UNITS	"days"
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"A read-only number of 1-day performance history intervals for
		which the data was collected.  The value of this object will be
		7 or the maximum number of 1-day history intervals collected by
		the implementation, unless the measurement was (re)started
		recently, in which case the value will be the number of complete
		1-day intervals for which there are at least some data.
		In certain cases, it is possible that some intervals are
		unavailable.  In this case, this object reports the maximum
		interval number for which data is available."
	REFERENCE
		"[TR-159], Section 5.5.1.45"
	-- 1.3.6.1.2.1.210.1.1.6.4.1.5
	::= { g9983SvcPmCurEntry 5 }


g9983SvcPmCur1DayInvalidIntervals OBJECT-TYPE
	SYNTAX  Unsigned32 (0..7)
	UNITS	"days"
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"A read-only number of 1-day performance history intervals for
		which the performance data was not always available.  The value
		will typically be zero, except in cases where the data for some
		intervals are not available."
	REFERENCE
		"[TR-159], Section 5.5.1.46"
	-- 1.3.6.1.2.1.210.1.1.6.4.1.6
	::= { g9983SvcPmCurEntry 6 }


g9983SvcPmCur1DayTimeElapsed OBJECT-TYPE
	SYNTAX  HCPerfTimeElapsed
	UNITS	"seconds"
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"A read-only count of seconds that have elapsed since the
		beginning of the current 1-day performance interval."
	REFERENCE
		"[TR-159], Section 5.5.1.47"
	-- 1.3.6.1.2.1.210.1.1.6.4.1.7
	::= { g9983SvcPmCurEntry 7 }


g9983SvcPmCur1DayDowns OBJECT-TYPE
	SYNTAX  HCPerfCurrentCount
	UNITS	"seconds"
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"A read-only count of seconds in the current 1-day performance
		interval during which a particular TDIM service was
		'down', as indicated by the g9983OperSvcState object.

		This object is inhibited during Unavailable Seconds (UAS)."
	-- 1.3.6.1.2.1.210.1.1.6.4.1.8
	::= { g9983SvcPmCurEntry 8 }


-- Service PM history: 15-min buckets

g9983SvcPm15MinTable OBJECT-TYPE
	SYNTAX  SEQUENCE OF G9983SvcPm15MinEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"This table contains historical 15-minute buckets of Performance
		Monitoring information for the services of a G.Bond/TDIM port
		(a multi-dimensional row for each 15-minute interval, up to 96
		intervals).

		Entries in this table MUST be maintained in a persistent manner."
	-- 1.3.6.1.2.1.210.1.1.6.5
	::= { g9983PM 5 }


g9983SvcPm15MinEntry OBJECT-TYPE
	SYNTAX  G9983SvcPm15MinEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"An entry in the G.Bond/TDIM Service historical 15-minute PM
		table.
		Each entry represents Performance Monitoring data for a
		particular service, indexed by the g9983SvcIdx, in a G.Bond
		TDIM port, indexed by the ifIndex, collected during a particular
		15-minute interval, indexed by the
		g9983SvcPm15MinIntervalIndex."
	INDEX {
		ifIndex,
		g9983SvcIdx,
		g9983SvcPm15MinIntervalIndex }
	-- 1.3.6.1.2.1.210.1.1.6.5.1
	::= { g9983SvcPm15MinTable 1 }


G9983SvcPm15MinEntry ::= SEQUENCE {

	g9983SvcPm15MinIntervalIndex    Unsigned32,
	g9983SvcPm15MinIntervalMoniTime HCPerfTimeElapsed,
	g9983SvcPm15MinIntervalDowns    HCPerfIntervalCount,
	g9983SvcPm15MinIntervalValid    TruthValue }


g9983SvcPm15MinIntervalIndex OBJECT-TYPE
	SYNTAX  Unsigned32 (1..96)
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"Performance data interval number.  1 is the most recent
		previous interval; interval 96 is 24 hours ago.
		Intervals 2..96 are OPTIONAL.

		This object partially maps to the TR-159 attribute
		aGroupPerf15MinIntervalNumber."
	REFERENCE
		"[TR-159], Section 5.5.1.57"
	-- 1.3.6.1.2.1.210.1.1.6.5.1.1
	::= { g9983SvcPm15MinEntry 1 }


g9983SvcPm15MinIntervalMoniTime OBJECT-TYPE
	SYNTAX  HCPerfTimeElapsed
	UNITS	"seconds"
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"A read-only count of seconds over which the performance data
		was actually monitored.  This value will be the same as the
		interval duration (900 seconds), except in a situation where
		performance data could not be collected for any reason."
	-- 1.3.6.1.2.1.210.1.1.6.5.1.2
	::= { g9983SvcPm15MinEntry 2 }


g9983SvcPm15MinIntervalDowns OBJECT-TYPE
	SYNTAX  HCPerfIntervalCount
	UNITS	"seconds"
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"A read-only count of seconds in the 15-minute performance
		history interval during which a particular TDIM service was
		'down', as indicated by the g9983OperSvcState object.

		This object is inhibited during Unavailable Seconds (UAS)."
	-- 1.3.6.1.2.1.210.1.1.6.5.1.3
	::= { g9983SvcPm15MinEntry 3 }


g9983SvcPm15MinIntervalValid OBJECT-TYPE
	SYNTAX  TruthValue
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"A read-only object indicating whether or not this history
		bucket contains valid data.  A valid bucket is reported as
		true(1) and an invalid bucket as false(2).





		If this history bucket is invalid, the BTU-C MUST NOT produce
		notifications based upon the value of the counters in this
		bucket.
		Note that an implementation may decide not to store invalid
		history buckets in its database.  In such a case, this object
		is not required, as only valid history buckets are available
		while invalid history buckets are simply not in the database.

		This object partially maps to the TR-159 attribute
		aGroupPerf15MinIntervalValid."
	REFERENCE
		"[TR-159], Section 5.5.1.58"
	-- 1.3.6.1.2.1.210.1.1.6.5.1.4
	::= { g9983SvcPm15MinEntry 4 }


-- Service PM history: 1-day buckets

g9983SvcPm1DayTable OBJECT-TYPE
	SYNTAX  SEQUENCE OF G9983SvcPm1DayEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"This table contains historical 1-day buckets of Performance
		Monitoring information for the services of a G.Bond/TDIM port
		(a multi-dimensional row for each 1-day interval, up to 7
		intervals).
		Entries in this table MUST be maintained in a persistent manner."
	-- 1.3.6.1.2.1.210.1.1.6.6
	::= { g9983PM 6 }


g9983SvcPm1DayEntry OBJECT-TYPE
	SYNTAX  G9983SvcPm1DayEntry
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"An entry in the G.Bond/TDIM Service historical 1-day PM table.
		Each entry represents Performance Monitoring data for a
		particular service, indexed by the g9983SvcIdx, defined in a
		G.Bond/TDIM port, indexed by the ifIndex, collected during a
		particular 1-day interval, indexed by the
		g9983SvcPm1DayIntervalIndex."
	INDEX {
		ifIndex,
		g9983SvcIdx,
		g9983SvcPm1DayIntervalIndex }
	-- 1.3.6.1.2.1.210.1.1.6.6.1
	::= { g9983SvcPm1DayTable 1 }


G9983SvcPm1DayEntry ::= SEQUENCE {

	g9983SvcPm1DayIntervalIndex    Unsigned32,
	g9983SvcPm1DayIntervalMoniTime HCPerfTimeElapsed,
	g9983SvcPm1DayIntervalDowns    HCPerfIntervalCount,
	g9983SvcPm1DayIntervalValid    TruthValue }


g9983SvcPm1DayIntervalIndex OBJECT-TYPE
	SYNTAX  Unsigned32 (1..7)
	MAX-ACCESS not-accessible
	STATUS  current
	DESCRIPTION
		"Performance data interval number.  1 is the most recent
		previous interval; interval 7 is 7 days ago.
		Intervals 2..7 are OPTIONAL.

		This object partially maps to the TR-159 attribute
		aGroupPerf1DayIntervalNumber."
	REFERENCE
		"[TR-159], Section 5.5.1.62"
	-- 1.3.6.1.2.1.210.1.1.6.6.1.1
	::= { g9983SvcPm1DayEntry 1 }


g9983SvcPm1DayIntervalMoniTime OBJECT-TYPE
	SYNTAX  HCPerfTimeElapsed
	UNITS	"seconds"
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"A read-only count of seconds over which the performance data
		was actually monitored.  This value will be the same as the
		interval duration (86400 seconds), except in a situation where
		performance data could not be collected for any reason.

		This object partially maps to the TR-159 attribute
		aGroupPerf1DayIntervalMoniSecs."
	REFERENCE
		"[TR-159], Section 5.5.1.64"
	-- 1.3.6.1.2.1.210.1.1.6.6.1.2
	::= { g9983SvcPm1DayEntry 2 }


g9983SvcPm1DayIntervalDowns OBJECT-TYPE
	SYNTAX  HCPerfIntervalCount
	UNITS	"seconds"
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"A read-only count of seconds in the 1-day performance history
		interval during which a particular TDIM service was 'down',
		as indicated by the g9983OperSvcState object.

		This object is inhibited during Unavailable Seconds (UAS)."
	-- 1.3.6.1.2.1.210.1.1.6.6.1.3
	::= { g9983SvcPm1DayEntry 3 }


g9983SvcPm1DayIntervalValid OBJECT-TYPE
	SYNTAX  TruthValue
	MAX-ACCESS read-only
	STATUS  current
	DESCRIPTION
		"A read-only object indicating whether or not this history
		bucket contains valid data.  A valid bucket is reported as
		true(1) and an invalid bucket as false(2).
		If this history bucket is invalid, the BTU-C MUST NOT produce
		notifications based upon the value of the counters in this
		bucket.
		Note that an implementation may decide not to store invalid
		history buckets in its database.  In such a case, this object
		is not required, as only valid history buckets are available
		while invalid history buckets are simply not in the database.

		This object partially maps to the TR-159 attribute
		aGroupPerf1DayIntervalValid."
	REFERENCE
		"[TR-159], Section 5.5.1.63"
	-- 1.3.6.1.2.1.210.1.1.6.6.1.4
	::= { g9983SvcPm1DayEntry 4 }


--
-- Conformance Statements
--

g9983Groups OBJECT IDENTIFIER 
	-- 1.3.6.1.2.1.210.2.1
	::= { g9983Conformance 1 }

g9983Compliances OBJECT IDENTIFIER 
	-- 1.3.6.1.2.1.210.2.2
	::= { g9983Conformance 2 }

-- Object Groups

g9983BasicGroup OBJECT-GROUP
	OBJECTS {
		g9983PortConfAdminServices,
		g9983PortStatCrc4Errors,
		g9983PortStatCrc6Errors,
		g9983PortStatCrc8Errors,
		g9983PortCapFecSupported,
		g9983OperSvcIdx,
		g9983OperSvcState,
		g9983SvcIfIdx,
		g9983SvcType,
		g9983SvcSize,
		g9983SvcRowStatus,
		g9983PortStatFltStatus }
	STATUS  current
	DESCRIPTION
		"A collection of objects representing management information
		for G.Bond/TDIM ports."
	-- 1.3.6.1.2.1.210.2.1.1
	::= { g9983Groups 1 }

g9983FecGroup OBJECT-GROUP
	OBJECTS {
		g9983PortCapFecSupported,
		g9983PortConfFecAdminState,
		g9983PortStatFecOperState,
		g9983PortConfFecWordSize,
		g9983PortConfFecRedundancySize,
		g9983PortConfFecInterleaverType,
		g9983PortConfFecInterleaverDepth,
		g9983PortCapFecMaxWordSize,
		g9983PortCapFecMaxRedundancySize,
		g9983PortCapFecInterleaverTypeSupported,
		g9983PortCapFecMaxInterleaverDepth }
	STATUS  current
	DESCRIPTION
		"A collection of objects supporting the OPTIONAL Forward Error
		Correction (FEC) and Interleaver function in G.Bond/TDIM
		ports."
	-- 1.3.6.1.2.1.210.2.1.2
	::= { g9983Groups 2 }

g9983AlarmConfGroup OBJECT-GROUP
	OBJECTS {
		g9983PortConfSvcUpDownEnable }
	STATUS  current
	DESCRIPTION
		"A collection of objects required for configuration of alarm
		thresholds and notifications in G.Bond/TDIM ports."
	-- 1.3.6.1.2.1.210.2.1.3
	::= { g9983Groups 3 }

g9983NotificationGroup NOTIFICATION-GROUP
	NOTIFICATIONS {
		g9983SvcUp,
		g9983SvcDown }
	STATUS  current
	DESCRIPTION
		"This group supports notifications of significant conditions
		associated with G.Bond/TDIM ports."
	-- 1.3.6.1.2.1.210.2.1.4
	::= { g9983Groups 4 }

g9983PerfCurrGroup OBJECT-GROUP
	OBJECTS {
		g9983PortPmCur15MinValidIntervals,
		g9983PortPmCur15MinInvalidIntervals,
		g9983PortPmCur15MinTimeElapsed,
		g9983PortPmCur15MinCrc4s,
		g9983PortPmCur15MinCrc6s,
		g9983PortPmCur15MinCrc8s,
		g9983PortPmCur1DayValidIntervals,
		g9983PortPmCur1DayInvalidIntervals,
		g9983PortPmCur1DayTimeElapsed,
		g9983PortPmCur1DayCrc4s,
		g9983PortPmCur1DayCrc6s,
		g9983PortPmCur1DayCrc8s,
		g9983SvcPmCur15MinValidIntervals,
		g9983SvcPmCur15MinInvalidIntervals,
		g9983SvcPmCur15MinTimeElapsed,
		g9983SvcPmCur15MinDowns,
		g9983SvcPmCur1DayValidIntervals,
		g9983SvcPmCur1DayInvalidIntervals,
		g9983SvcPmCur1DayTimeElapsed,
		g9983SvcPmCur1DayDowns }
	STATUS  current
	DESCRIPTION
		"A collection of objects supporting OPTIONAL current Performance
		Monitoring information for G.Bond/TDIM ports."
	-- 1.3.6.1.2.1.210.2.1.5
	::= { g9983Groups 5 }

g9983Perf15MinGroup OBJECT-GROUP
	OBJECTS {
		g9983PortPm15MinIntervalMoniTime,
		g9983PortPm15MinIntervalCrc4s,
		g9983PortPm15MinIntervalCrc6s,
		g9983PortPm15MinIntervalCrc8s,
		g9983PortPm15MinIntervalValid,
		g9983SvcPm15MinIntervalMoniTime,
		g9983SvcPm15MinIntervalDowns,
		g9983SvcPm15MinIntervalValid }
	STATUS  current
	DESCRIPTION
		"A collection of objects supporting OPTIONAL historical
		Performance Monitoring information for G.Bond/TDIM ports, during
		previous 15-minute intervals."
	-- 1.3.6.1.2.1.210.2.1.6
	::= { g9983Groups 6 }

g9983Perf1DayGroup OBJECT-GROUP
	OBJECTS {
		g9983PortPm1DayIntervalMoniTime,
		g9983PortPm1DayIntervalCrc4s,
		g9983PortPm1DayIntervalCrc6s,
		g9983PortPm1DayIntervalCrc8s,
		g9983PortPm1DayIntervalValid,
		g9983SvcPm1DayIntervalMoniTime,
		g9983SvcPm1DayIntervalDowns,
		g9983SvcPm1DayIntervalValid }
	STATUS  current
	DESCRIPTION
		"A collection of objects supporting OPTIONAL historical
		Performance Monitoring information for G.Bond/TDIM ports, during
		previous 1-day intervals."
	-- 1.3.6.1.2.1.210.2.1.7
	::= { g9983Groups 7 }


-- Compliance Statements

g9983Compliance MODULE-COMPLIANCE
	STATUS  current
	DESCRIPTION
		"The compliance statement for G.Bond/TDIM interfaces.
		Compliance with the following external compliance statements
		is REQUIRED:

		MIB Module             Compliance Statement
		----------             --------------------
		IF-MIB                 ifCompliance3
		GBOND-MIB              gBondCompliance"

	MODULE 
	MANDATORY-GROUPS {
			g9983BasicGroup,
			g9983AlarmConfGroup,
			g9983NotificationGroup }

	GROUP g9983FecGroup
	  DESCRIPTION
		"Support for this group is only required for implementations
		supporting the G.Bond/TDIM FEC and Interleaver function."
	GROUP g9983PerfCurrGroup
	  DESCRIPTION
		"Support for this group is only required for implementations
		supporting Performance Monitoring."
	GROUP g9983Perf15MinGroup
	  DESCRIPTION
		"Support for this group is only required for implementations
		supporting historical Performance Monitoring."
	GROUP g9983Perf1DayGroup
	  DESCRIPTION
		"Support for this group is only required for implementations
		supporting historical Performance Monitoring."
	-- 1.3.6.1.2.1.210.2.2.1
	::= { g9983Compliances 1 }

END
